polti Vaporella EXPRESS VE30.10 / VE30.20 / VE30.30 / VE30.40 Manual
![]()
CORRECT USE OF THE PRODUCT
Polti Vaporella Express is intended for domestic use as steam generator iron, with separate tank in accordance with the descriptions and instructions contained in this manual. Please read these instructions carefully and keep them. This manual is also available on the website www.polti.com. POLTI S.p.A. reserves the right to make the aesthetic, technical and construction changes it deems necessary, without prior notice. Before leaving our factory all our products are rigorously tested. Therefore, Polti Vaporella Express may already contain some residual water in the tank.
Correct use of the product is only as detailed in this instruction manual. Any other use may damage the appliance and invalidate the warranty.
WHICH WATER TO USE
Polti Vaporella Express was designed to operate with a mixture composed of 50% tap water having a hardness up to 20° f and 50% commercially-available demineralised water. If the water used is particularly hard (above 20° f), excessive limescale could accumulate in the appliance, if so use demineralised water only.
![]()
check the hardness of the water at the technical office at your local council or the local water supplier.
Never use rain water or water containing additives (e.g. starch, perfumes), perfumed water or water produced by other domestic appliances, water softeners and filter jugs. Do not add chemical, natural, detergent, or limescale removing substances, etc. Do not use Polti Kalstop.
PREPARATION FOR USE
- Position Polti Vaporella Express on a stable, flat, heat-resistant surface.
- Fill the tank with water (1) up to the MAX line.
![]()
This operation must always be carried out with the power cable disconnected from the mains.
Thanks to the continuous refill system you do not need to stop your ironing and wait for the appliance to cool down because the tank can be refilled as needed. - Release the iron from the rest (see STORAGE).
- Connect the cable plug to an earthed power supply of the correct voltage (2).
![]()
- Make sure you have completely unrolled the water hose.
- To turn on the appliance press ON/OFF button
on the iron handle (3):
![]()
the
light (4)
![]()
and the iron's blue LED will flash. When both lights stop flashing, the appliance is ready to start ironing and produce steam.
The sound emitted on your appliance during use is due to the water refilling system and is quite normal.
STEAM IRONING
Polti Vaporella Express is equipped with an intelligent iron, where the temperature is perfect for ironing every kind of fabric. Polti Vaporella Express has 2 steam settings available with the SET button (5):
![]()
The MAX FUNCTION
- to easily iron even the heaviest fabrics (4).
The ECO FUNCTION - allows you to save energy whilst you iron and enjoy the best possible performance at the same time, even with the most difficult fabrics (cotton/denim/linen) (6).
![]()
Press the steam button on the iron (7) to start the steam coming out of the holes on the soleplate. Start ironing the garments. Releasing the steam button (7), the steam flow stops.
![]()
When first using the steam, there may be some drops of water leaking out of the plate, this is due to thermal stabilization. It is recommended that the first jets of steam are not directed onto the fabric that needs ironing.
![]()
Do not leave the hot plate on any surface. Use the Polti Vaporella Express vertical rest, placing the rear part of the iron directly onto the ironing board or surface on which you are ironing (8).
![]()
The appliance also comes with a handy iron rest mat (fixed) with non-slip pads designed to withstand hot temperatures.
THE STEAM-JET STEAM BOOST FUNCTION
The STEAM BOOST function can be activated for quick and easy ironing by double-clicking the steam button on the iron (7). A powerful blast of steam will allow you to speed up and improve ironing, even on heavy fabrics, and to remove the most difficult creases.
VERTICAL IRONING
The iron may be used in the vertical position to remove creases from fabrics and/or to refresh the fabric fibres, eliminating any residual odours.
Hold the iron in a vertical position, press the steam button (7), and if permissible based on the type of fabric, touch it lightly with the soleplate.
DRY IRONING / DELICATE FABRICS
- Ensure that "PREPARATION FOR USE" section has been followed.
- Continue ironing without pressing the steam button on the iron.
When ironing dry, pay attention not to press the steam button, since water could leak from the soleplate.
AUTOMATIC SHUT- OFF
After 10 minutes of inactivity, the auto shutoff is shown by the flashing of both the blue light and the clock symbol and signalled by an acoustic buzzer repeated 6 times. To reactivate Polti Vaporella Express, press the steam button on the iron (7).
OUT OF WATER
The water level is always visible on the tank. When there is no water in the tank, the red indicator
displays on the iron handle (9).
![]()
ATTENTION: When the tank is empty, the 'no water' light will only flash after the steam button has been pressed continuously for about 40 seconds.
To restart ironing:
- Fill the tank as described in "PREPARATION FOR USE" section.
- Hold down the button on the iron (7) until steam comes out.
CALC CLEANING SYSTEM
The Polti Vaporella Express Calc Cleaning system enables the removal of limescale, thus guaranteeing a better supply of steam, avoiding the leakage of stains or dirt from the holes in the plate.
Running the Calc Cleaning cycle regularly gives your Polti Vaporella better performance and durability over time. Run the cycle whenever the
button lights up (10).
![]()
Before running the cleaning cycle, make sure you have a large receptacle or bowl on hand to collect the water, steam and limescale that will come out from the iron during the process, thus avoiding the wetting of the ironing board or surface on which you are ironing.
How to clean limescale using the "Calc Cleaning" cycle:
- Fill the tank halfway with water.
- Make sure the machine is on.
- Position the iron over a receptacle or bowl;
- Hold down the
(11) button until the light
(10) starts to flash (about 3 seconds).
![]()
- During the cleaning cycle, hot water, steam and limescale particles will start to come out of the iron. The cleaning cycle takes approximately 2 minutes; do not interrupt the flow until it is complete.
- At the end of the cleaning cycle, three beeps will indicate that the procedure has finished; the
(10) light will stop flashing and the MAX function light will turn on
. (4). - After having run the Calc Cleaning procedure, residual water may leak from the plate.
- Dry the iron with a cloth.
![]()
The iron is hot.
- You may now resume normal ironing. If you need to stop before the cleaning cycle finishes, hold down the ON/OFF switch
(3) for 2 seconds. The appliance will turn off, and cleaning will be interrupted.
GENERAL MAINTENANCE
Except when running the Calc Cleaning cycle, always unplug the appliance from the power mains before conducting any maintenance on it, making sure that the product has cooled down before proceeding.
To clean the outside of the appliance, use only a damp cloth. Do not use detergents of any type.
Clean the iron soleplate when it is completely cold with a damp cloth or with a non-abrasive sponge.
STORAGE
- Turn off the appliance and disconnect from the mains electricity.
- Wait for the appliance to cool down completely before storing it.
- Empty the water tank.
- Place the iron onto the mat, securing it with the special locking button on the front of the appliance (12).
![]()
Press the button to unlock it
(13)
![]()
- Place the water tube in its casing (14).
![]()
TROUBLESHOOTING
PROBLEM | CAUSE | SOLUTION |
Steam does not come out from the Iron soleplate. | No power ON/OFF switch is off. | Check that the power is on and that the ON/OFF switch is pressed. |
Water tank is empty. | Fill the water tank. |
Little steam comes from the Iron soleplate. | The steam is dry, so is barely visible, but is present and effective. | This is normal especially in particular environmental conditions. |
You have not kept the steam button continuously pressed. | Keep the iron steam button pressed while ironing. |
You are ironing in Eco mode. | For a more powerful jet of steam, deactivate Eco mode and iron using the Max function. |
Water comes out from the Iron soleplate instead of steam. | The temperature dial is not turned to maximum value. | Rotate the temperature dial to maximum. |
First steam release. | Release onto a cloth until steam comes out from the holes on the solepate. |
The Calc Cleaning system just finished and any remaining water might leak from the plate. | Dry the iron with a cloth and resume normal ironing. |
The Steam Boost function was activated several times. | Always wait for the iron to reach maximum temperature between one activation and the next. |
Calc Cleaning function activated. | End the cleaning cycle. |
Traces of water remain on the garments. | The ironing-board lining is impregnated with water. | Check that the ironing board is suitable (a board with a grill that prevents condensation). |
The 'no water' button does not light up. | The tank is not empty and/or the steam button was not held down continuously for 40 seconds. | If this happens regularly, see "AUTOMATIC SHUT- OFF" Section. |
The steam does not discharge immediately after the steam button has been pressed. | The water in the tank turns into steam in the iron plate. When you press the steam button, it takes 1-2 seconds to generate steam and discharge it. | This is normal, press and hold down the iron steam button while ironing. |
The steam will continue to discharge after the steam button has been released. | The water in the tank turns into steam in the iron plate. When the button is released, the remaining water is turned into steam. | Release the steam button for 2-3 seconds before placing the iron onto the mat or in a vertical position. |
When the iron is placed on the mat or in a vertical position, a strong jet of steam discharges, even after the button on the iron has been released. | When the iron is in the vertical position, the remaining water is collected and converted into steam with an intense delivery. | This is normal. Release the steam button for 2-3 seconds before placing the iron onto the mat or in a vertical position. |
If problems persist or are not listed above, please contact a Polti Authorised Service Centre (www.polti.com for the updated list) or contact Customer Services. |
WARRANTY AND SERVICE
To see the up-to-date list of the Polti Authorised Service Centres, visit the website www.polti.com.
It is covered by a legal warranty against defects existing at the time of delivery for two years from the date of purchase.
To activate the warranty and for further information, visit www.polti.com
The optional accessories are on sale at all the best domestic appliance retailers, an Authorised Polti Service Centre or online at www.polti.com.
ACCESSORIES FOR ALL NEEDS
Visit our site www.polti.com or any of the top household appliance stores, where you will find a range of accessories to enhance the performance and convenience of your appliance and make household tasks even simpler.
To check the compatibility of an accessory with your appliance, search the code PAEUXXXX/FPASXXXX listed next to each accessory. If the accessory code you wish to buy is not listed in this manual, please contact our Customer Service team for more information.
REGISTER YOUR PRODUCT
Visit our website www.polti.com or call our Customer Services department to register your product. You can benefit from a special welcome offer, in participating countries, and keep up to date on all the latest Polti news, as well as buy accessories and consumables.
To register your product, in addition to your personal information, you must enter the serial number (SN) which you will find on the label, located on the box and on the appliance. To save time and have your serial number to hand, write it down.
OFFICIAL YOUTUBE CHANNEL
Want to know more?
Visit our official channel: www.youtube.com/poltispa.
We'll show you the natural power and ecological effectiveness of steam both for ironing and for cleaning, through many videos of Polti Vaporella and of all other products in Polti's world.
Sign up to the official channel to keep yourself updated about our video contents!
ATTENTION: The safety warnings are only shown in this manual.
IMPORTANT PRECAUTIONS FOR USE
Before using the appliance, read all the warnings and instructions provided. This appliance is intended for indoor domestic use only. Polti S.p. A. will consider the warranty void and accept no liability for damages or accidents in cases of commercial use or use which does not comply with the warnings and instructions provided.
SAFETY SYMBOLS
![]()
High temperature. Risk of scalding! If shown on the appliance, do not touch, as parts may be very hot.
![]()
![]()
Steam. Risk of scalding!
This appliance reaches very high temperatures. Incorrect use of the device can cause scalding.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Do not use the appliance at altitudes of greater than 2,000 ma.s.l.
- The iron must not be used if it has been dropped, if there are visible signs of damage or if it leaks.
- The appliance must not be left unattended if plugged in to the mains. Unplug it whenever it is not in use.
- Only pour water or the water mix indicated in the chapter "Which water to use" into the tank and boiler. No additives, detergents or other substances of any type are permitted unless they have been approved by Polti.
- The appliance must be placed on a stable, flat, heat-resistant surface when in use. If using the iron rest, make sure to place it on a stable surface. Do not rest the appliance on soft surfaces like the ironing board cover. Do not use close to containers full of water.
- Whenever possible, use the iron with the iron rest (fixed or removable as provided, or an original replacement).
- Do not rest the iron on its base without the iron rest.
- Do not direct steam towards equipment containing electric and/or electronic components. Do not direct steam at toxic substances, acids, solvents, detergents, corrosive substances or explosive substances. Keep the appliance far from dangerous substances during use.
- Do not direct the steam jet towards the iron rest and/or towards the appliance itself.
- Do not direct the steam jet or the iron itself towards people or animals.
- Do not place the appliance near sources of heat such as fireplaces, stoves and ovens.
- Do not obstruct the openings and grills on the appliance.
- If ironing whilst sitting down, take care to ensure that the steam jet is not angled towards your legs.
- Before connecting the appliance to the mains, ensure that the continuous steam jet button (if present) is not pressed.
- Do not leave the iron unattended when the steam is activated.
- Do not put the appliance away until it has cooled down.
ELECTRICAL SAFETY WARNINGS
- Plug the appliance into a single grounded socket, making sure that the socket is part of an electrical system that complies with applicable laws, with a voltage of between 220-240V and a frequency of 50-60Hz. Do not use multi-socket outlets.
- Make sure that any extension leads used are certified for use at 16 A and have an earth connection.
- Always turn the appliance off before unplugging it (if it has a main power switch).
- Grasp the plug to disconnect it from the socket. Do not pull it out by the cable.
- Unwind cables completely before plugging into the mains.
- Do not pull or tug cables or subject them to tension (by twisting, crushing or stretching). Keep them away from hot and/or sharp surfaces and parts. Avoid contact with the hot iron plate or closing in doors or windows. Do not pull cables tight around corners. Avoid treading on the cables. Do not wrap cables around the appliance.
- Do not touch or use the appliance barefoot and/or with wet body or feet.
- Do not immerse the appliance in water or other liquids.
- Remove the plug from the power socket before filling the tank/boiler with water.
FILLING APPLIANCES WITH A SAFETY CAP
- Immediately after the cap has been opened, while the boiler is still hot, wait before filling the appliance, even if it has been unplugged from the mains. On contact with the hot, empty boiler, cold water will evaporate and produce a spray of steam, which can cause burns where it contacts the skin. Only fill the boiler when it is cold, and always keep your face away from the mouth of the boiler when filling.
- If water runs out during ironing, proceed as follows:
- Turn off the boiler switch (
), if present. - Make sure that there is absolutely no water, and therefore no steam, left by pressing the button on the iron.
- Switch the appliance off and unplug it from the mains.
- Wait 10 minutes and then, keeping your face well away from the cap and the mouth of the boiler, remove the safety cap by unscrewing it without using force. (***)
- Leave the appliance to cool down for at least 10 more minutes.
- Fill the boiler back up with water as described in the instructions, never by placing it directly below running water. - Put the safety cap back on, checking that it is fully tightened.
(***) ATTENTION: If, while unscrewing it, the cap spins freely or if steam is escaping, stop the operation immediately and make sure that the appliance is switched off with the cable unplugged from the mains. Then, wait for the appliance to cool down (at least 2 hours) and unscrew the cap before removal.
- Always use the appliance with the safety cap supplied or an original replacement part.
- Do not plug it into the electrical socket if the cap is not fully tightened.
- Before turning the appliance on, check that there is not hing blocking the mouth of the boiler (filler bottle, funnel, or other objects). Check that the cap is correctly tightened. If steam is escaping from the cap, switch off the boiler, unplug the power cable, wait for 2 hours for the appliance to cool, and then unscrew the cap. Check the condition of the cap and its seal. If the cap is in good condition, screw it back on completely. If steam continues to escape from the cap, take the appliance to the nearest authorised service centre.
- Check the condition of the cap and its seal regularly. Impact and being dropped may compromise the safety of the cap. Replace with an original spare part or replace the seal.
- If the cap spins freely, this indicates that the boiler is still pressurised and, therefore, hot. Never force the cap open, whether the appliance is switched on or the boiler is switched off and the appliance is disconnected from the mains.
- Do not use tools to unscrew the cap. If the cap cannot be removed, even once the appliance has cooled, go to your nearest authorised service centre.
- Using non-original Polti safety caps constitutes improper use and can lead to accidents.
WARNINGS FOR MAINTENANCE
- Never disassemble or carry out maintenance on the appliance apart from that indicated in the warnings and instructions. In the event of a fault or malfunction, do not try and repair the appliance yourself. Incorrect use or nonobservance of the instructions herein may lead to serious accidents. Always contact Authorised Service Centres.
- If the power cable and the iron cord are damaged, they must be replaced by the manufacturer, one of its service centres or a similarly qualified person in order to avoid any risks. Do not use the appliance with damaged cables. Do not change the plug on the power cable. Only use original Polti parts.
- Openings intended to be used for filling, descaling, rinsing o rinspection which are pressurised must not be opened during use or while there is hot water in the boiler (only for irons with pressurised containers).
- Appliances with a safety cap must never be filled while there is still steam or water in the boiler or while it is pressurised.
- In order to carry out maintenance (descaling, rinsing, inspection) on pressurised boilers with hot water inside, unplug the appliance from the electrical socket for at least 2 hours, check that it is cold, and then remove the cap by carefully unscrewing it. For maintenance which requires the appliance to be plugged in, such as the Self-Cleaning function, watch out for jets of steam and hot water and pay attention to the temperature of the iron.
- Keep the appliance and the power cable out of the reach of children under 8 years of age when the appliance is plugged in or is cooling down.
- Keep all the parts of the packaging out of the reach of children; they are not toys. Keep the plastic bag out of the reach of children: danger of suffocation.
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download polti Vaporella EXPRESS VE30.10 / VE30.20 / VE30.30 / VE30.40 Manual
Need help?
Do you have a question about the Vaporella EXPRESS VE30.10 and is the answer not in the manual?
Questions and answers