Boss Super Overdrive SD-1 Manual
![]()
Main Features
Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (supplied on a separate sheet). After reading, keep the document(s) where it will be available for immediate reference.
- Unlike earlier fuzz units, the SD-1 can faithfully express the picking dynamics and subtle nuances of your playing. Regardless of the type of guitar you're using, the true character of its tone will come through.
- This unit generates a soft and clear distortion like that of an overdriven tube amp.
- In addition, you can use the tone control to boost or cut the high-frequency range, creating a versatile range of effects.
- When the effect is on, the LED is lit, showing at a glance whether the effect is on or off.
Panel Descriptions
![Boss - Super Overdrive - Panel Descriptions Panel Descriptions]()
Precautions When Connecting
- To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units before making any connections.
- Once everything is properly connected, be sure to follow the procedure below to turn on their power. If you turn on equipment in the wrong order, you risk causing malfunction or equipment failure. When powering up: Turn on the power to your guitar amp last. When powering down: Turn off the power to your guitar amp first.
- Before turning the unit on/off, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when switching the unit on/off. However, this is normal and does not indicate a malfunction.
Use of Battery
- A battery was installed in the unit before it left the factory. The life of this battery may be limited, however, since its primary purpose was to enable testing.
- If you handle batteries improperly, you risk explosion and fluid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (supplied on a separate sheet).
- When operating on battery power only, the unit's indicator will become dim when battery power gets too low. Replace the battery as soon as possible.
- Batteries should always be installed or replaced before connecting any other devices. This way, you can prevent malfunction and damage.
Operating the Unit
- After connecting all cords required, set all knobs on the panel as illustrated.
![]()
- Depress the pedal switch. Check LED lights to indicate "EFFECT ON" and extinguishes to indicate "EFFECT OFF."
* This check LED is also used to check battery. If LED fails to light or becomes dim, the battery should be replaced.
![]()
- Turn DRIVE knob to proper position.
![]()
- While switching pedal ON and OFF, turn LEVEL knob to proper position so no volume difference between Normal and Effect modes is noticed.
![]()
- Turn TONE knob to proper position.
![]()
Changing the Battery
![]()
- Hold down the pedal and loosen the thumbscrew, then open the pedal upward.
* The pedal can be opened without detaching the thumbscrew completely. - Remove the old battery from the battery housing, and remove the snap cord connected to it.
- Connect the snap cord to the new battery, and place the battery inside the battery housing.
* Be sure to carefully observe the battery's polarity (+ versus -). - Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing. - Finally, insert the thumbscrew into the guide bush hole and fasten it securely.
Main Specifications
Nominal Input Level | -20 dBu |
Input Impedance | 1 MΩ |
Nominal Output Level | -20 dBu |
Output Impedance | 1 kΩ |
Recommended Load Impedance | 10 kΩ or greater |
Power Supply | Carbon-zinc battery (9 V, 6F22) or Alkaline battery (9 V, 6LR61) AC adaptor (PSA series: sold separately) |
Current Draw | 10 mA * Expected battery life under continuous use: Carbon: 60 hours Alkaline: 90 hours These figures will vary depending on the actual conditions of use. |
Dimensions | 73 (W) x 129 (D) x 59 (H) mm 2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches |
Weight | 360 g / 13 oz (including battery) |
Accessories | Leaflet ("USING THE UNIT SAFELY," "IMPORTANT NOTES," and "Information") Carbon-zinc battery (9 V, 6F22) |
Options (sold separately) | AC adaptor (PSA-series) |
* 0 dBu = 0.775 Vrms
* This document explains the specifications of the product at the time that the document was issued. For the latest information, refer to the Roland website.
Documents / ResourcesDownload manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Boss Super Overdrive SD-1 Manual
Need help?
Do you have a question about the Super Overdrive and is the answer not in the manual?
Questions and answers