ThermoWorks RFX MEAT Operating Instructions

This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
This equipment complies with the FCC RF radiation
exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator
and your body.
This device complies with Industry Canada Licence-exempt
RSSs. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.
Special Notice
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:\
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician
for help.
FCC ID: 2AI67-TX5630 / IC ID: 22116-TX5630
www.thermoworks.com
741 E. Utah Valley Dr.
American Fork, UT 84003
For service or warranty:
1-800-393-6434
1-801-756-7705
techsupport@thermoworks.com
P-22-010-02-b
RFX MEAT
Operating Instructions
Getting Started:
RFX MEAT comes charged and ready to use.
Once you have added your RFX GATEWAY to
your account via the ThermoWorks App, click on
+Device on the bottom right of the devices screen
and follow the in-app instructions to attach your
RFX MEAT to your account.
Please Note: RFX GATEWAY will need to be added
to your account before your RFX MEAT can be
added.
What's included:
RFX MEAT, charging block, silicone probe rings,
1xAAA battery (installed), and this instruction
card. Calibration certificate can be downloaded
from ThermoWorks App.
Charging:
When placing RFX MEAT into the charging block,
make sure the reduced-tip penetration probe is
facing toward the rounded side of the charging
block (away from the LED charging light.)
When placed back into the charging block, the
LED will flash red and it will stop transmitting
temperatures. When the flashing stops, RFX MEAT
is fully charged (LED light will not turn green). RFX
MEAT fully charges in approximately 20 minutes
and will be 80% charged in approximately 10
minutes.
Please Note: The AAA battery in the charging
block will need to be replaced at least once per
year, even if it is not low. The ThermoWorks App
will automatically remind you when it is time to
change the battery.
™