Revised: September 2, 2024 Cisco IW-PWRADPT-MFIT Series Power Supply Installation Guide This document describes the Cisco IW-PWRADPT-MFIT series Power Supply (referred to as the power supply in this document) and provides instructions for mounting the unit. Product Overview The Cisco power supply models IW-PWRADPT-MFIT4P= and IW-PWRADPT-MFITIN= are an outdoor single-phase AC/DC, 60-Watt output external wide temperature range power supply with the DC voltage output of 48V.
Page 3
SST FLAT WASHER (4X) SST SPLIT LOCK WASHER (4X) 6-32 NUT (4X) If any item is missing or damaged, contact your Cisco representative or reseller. AC Cable Assembly Connect the corresponding phase of wire of AC cable with power system.
Page 4
Plug Type Country Plug Type Country European, Morocco Korea, Russia China, Australia, Argentina India, South Africa DC Cable Assembly The power adapter is pre-terminated with a Molex Microfit 3.0 Receptacle with two contacts populated. The remaining positions are unused. The following table shows the pinouts. Output cable length shall be one meter +/- 5%. Figure 2: Output Connector Molex Microfit Microfit 3.0 receptacle front view Molex Microfit...
Receptacle Header/Plug: 4 Pin Microfit 3.0 compatible Plug Molex Microfit 3.0 430250400, crimp terminal,female, 430300040 Technical Specifications This table lists specifications for the power supply: Table 3: Technical Specifications Specification IW-PWRADPT-MFIT4P= IW-PWRADPT-MFITIN= Input-voltage range and frequency AC input: 100-240V, 50-60Hz (nominal) DC input: 35 to 370 VDC Output voltage and current 48 VDC, 1.25A, 60 W Max...
Specification IW-PWRADPT-MFIT4P= IW-PWRADPT-MFITIN= Altitude Operating altitude: -500 to 17,000 feet from sea level Non-operating altitude:-1,000 to 30,000 feet from sea level Reliability MTBF: 300,000 hrs @ 40ºC Mechanical Specifications All measurements in the following figures are in mm. Figure 3: Adapter Dimensions (Top View) Figure 4: Adapter Dimensions (Side View)
You can attach the power adapter to the IW9167EH access point on a pole using the mounting bracket AIR-ACCPMK3700= or AIR-ACCPMK3700-2=. For detailed information on mounting procedures, see Attaching a Power Adapter Cisco Catalyst IW9167E Heavy Duty Access Point Hardware Installation Guide.
Page 8
Figure 6: Exploded View Power Supply Split lock washer (SST) Insulator spacer integrated onto power adapter Flat washer (SST) 6-32, M3.5 or equivalent sized hardware, Not Supplied Nylon insulating washer Procedure Step 1 Using slots in Power Adapter or dimensions from detailed drawing, drill through holes or tapped holes depending on mounting surface type and hardware used to attach.
Page 9
Figure 7: Exploded View Power Supply Flat washer (SST) Insulator spacer integrated onto power adapter Nylon insulating washer 6-32 Nut 6-32UNC-2A threaded post Split lock washer (SST) Before you begin Note You may skip steps 1-3 when installing the power adapter on the mounting bracket AIR-ACCPMK3700= or AIR-ACCPMK3700-2= as these posts are integrated into these brackets.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...
Page 12
Americas Headquarters Asia Pacific Headquarters Europe Headquarters Cisco Systems, Inc. CiscoSystems(USA)Pte.Ltd. CiscoSystemsInternationalBV San Jose, CA 95134-1706 Singapore Amsterdam,TheNetherlands Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/offices.
Need help?
Do you have a question about the IW-PWRADPT-MFIT Series and is the answer not in the manual?
Questions and answers