Advertisement
Quick Links
Advertisement
Related Manuals for MATRIX TECHNOLOGY MPS-3035
Summary of Contents for MATRIX TECHNOLOGY MPS-3035
- Page 1 5CH Programmable Power Supply User Manual MATRIX TECHNOLOGY INC.
- Page 2 Preface Respected users: Thank you for purchasing a brand new MATRIX instrument. In order to use this instrument correctly, please read this manual carefully before using this instrument, especially the section on "Safety Precautions". If you have read the full text of this manual, it is recommended that you keep this manual in a safe place and place it with the instrument or in a place where you can read it at any time for future reference.
-
Page 3: Copyright Information
Products are protected by patents in China or other countries, including patents that have been obtained or are pending. ● MATRIX TECHNOLOGY INC. reserves the right to change product specifications and prices. ● is the registered trademark of MATRIX TECHNOLOGY INC. - Page 4 Verification and Correction Statement The company specifically declares that the instruments and equipment listed in this manual fully conform to the specifications and characteristics stated in the company's technical specifications. This instrument has passed the factory calibration of the company before leaving the factory, and the calibration procedures and steps are in line with the specifications and standards of the electronic inspection center.
-
Page 5: Table Of Contents
CONTENTS CHAPTER I PRODUCT INTRODUCTION......................1 CHAPTER II TECHNICAL SPECIFICATIONS....................2 2.1 Main technical specifications....................,........1 2.2 Supplementary features............................,..2 CHAPTER III QUICK START..........................3 3.1 Introduction to the front and rear panels........................3 3.2 Pre-check...................................4 3.3 If the power does not start............................5 CHAPTER Ⅳ PANEL OPERATION........................5 4.1 Keyboard introduction..............................6 4.2 Front panel basic operation............................6 4.3 Voltage setting...................................7... -
Page 6: Chapter Iproduct Introduction
• OCP, OVP, OTP and other protection functions • Five channels can independently adjust voltage and current ChapterⅡ Technical Specifications 2.1 Main technical specifications Five-channel programmable DC power supply technical specification table: Model MPS-3035 MPS-3055 MPS-6035 Rated input voltage AC220V/110V±5% Rated output voltage... -
Page 7: Supplementary Features
accuracy (25℃± Current ≤0.05%+2mA ≤0.05%+2mA ≤0.05%+2mA 5℃） Readback Voltage resolution Current 0.1mA 0.1mA 0.1mA Readback Voltage ≤0.05%+5 digits ≤0.05%+5 digits ≤0.05%+5 digits accuracy Current ≤0.05%+2mA ≤0.05%+2mA ≤0.05%+2mA (25℃±5℃） Temperature 0 to 40 ℃ ≤ 80 R.H. Operating environment -15 to 70 ℃ ≤ 80 R.H Storage environment Dimensions （W*H*D(mm)）... - Page 8 Picture 3.1 ①, ⑨ standard 19-inch cabinet fixing ears ②, ⑧ five-way programmable DC power supply handle ③ Power switch ④ LCD display, ⑤ Front output terminal, ⑥ From left to right are 0-9 number keys and ESC escape key, function keys, up and down movement keys and Enter key, ⑦...
-
Page 9: Pre-Check
Picture 3.2 Five-way programmable DC power supply rear panel ① Rear output terminal and SENSE (remote range port) "L" is the rear output terminal, "S" is SENSE, ② Heat dissipation hole ③ RS232 communication interface ④ Power input socket 3.2 Pre-check Please follow the steps below to check the power supply to ensure that the power supply can be used normally. -
Page 10: If The Power Does Not Start
3.3 If the power does not start Use the following methods to solve the problems you may encounter when turning on the power. 1. Check whether the power cord is connected properly Model Fuse specifications 230V 115V 2. Replacing the fuse Use a screwdriver to open the small plastic cover under the power input socket on the rear panel of the power supply, and you can see the fuse. -
Page 11: Keyboard Introduction
4.1 Keyboard introduction Key Description Button position Button function description 0-9 : Number key Esc : Number key input and exit I-Set Set the maximum output current V-Set Set power supply output voltage Save Power storage current correlation parameter to a specified storage location set Recall Recall power-related setting parameters from the designated storage... -
Page 12: Voltage Setting
4.3 Voltage setting The voltage setting range is between 0V and the maximum voltage setting value. You can use the following two methods to set the output voltage value through the front panel, and set the voltage to the value of the currently displayed channel. -
Page 13: Memory Recall Function
4.5 Memory Recall function The power supply can save some commonly used parameters in 9 groups of non-volatile memories for users to quickly recall and use. You can use the Save and Recall keys on the front panel to access the storage area (0~9). -
Page 14: Menu Setting
Note: After setting, press "ESC" to exit or wait about 10 seconds to exit automatically. 4.7 Menu setting Press shift and then the number key " 0 " to enter the menu setting function, press the ▲ and ▼ keys to switch options, the screen will display as follows: 1．P-UP ON/OFF ( Enable switch in power-on state, ON is turned on, OFF is turned off, set by the knob, and confirm by the "... - Page 15 3.Key Beep Set ON/OFF (beeper enable switch, ON is turned on, OFF is turned off, the default value is "ON", use the knob to change the setting, press the "Enter" key to save, when the button is set to ON, there is a sound, No sound when set to OFF button,) 4.Baud Rate Select 9600 (Communication baud rate setting, the default value is "9600", change the setting with the knob, press the "Enter"...
-
Page 16: Chapter Vremote Operation Mode
8. Reset Power NO (factory initialization setting, turn the knob left and right to change the selection, press "Enter" key to confirm, NO means no initialization, YES means initialization, all parameters will be set to factory defaults after initialization.) Chapter V Remote operation mode 5.1 Communication between power supply and PC The power supply can be connected to the PC interface through the DB9 plug on the rear panel. -
Page 17: Chapter Vi Scpi Communication Protocol
RXD（accept data） TXD（send data） GND（ground） Chapter VI SCPI communication protocol Command format According to the SCPI command syntax, the short mnemonic uppercase format is supported. 1. The braces ({}) contain the parameter options of the given command string. The braces are not sent with the command string. - Page 18 Calibration: None IEEE 488.2 common demand *IDN? This query command reads the identification string of the power supply. Return parameters: manufacturer name, product model, hardware version No., software version No.. SYSTem command SYSTem Commands are used to set and check system related status. SYSTem: LOCal This command sets the power supply to local operation mode.
- Page 19 APPly: CURRnet? This command check the set current value simultaneously. For example： APP:CURR? Return parameters: CH1 set current (X.XXX), CH2 set current (X.XXX), CH3 set current (X.XXX), CH4 set current (X.XXX), CH5 set current (X.XXX) XXX) APPly:OUTput {<0 |1 |ON|OFF>, <0 |1 |ON |OFF >,<0 |1 |ON|OFF >} This command sets the output status of 5 channels simultaneously.
- Page 20 MEASure: CURRent:ALL? This command simultaneously checks the actual output current values of 5 channels. For example: MEAS:CURR:ALL? Return parameters: CH1 actual current value (X.XXX), CH2 actual current value (X.XXX), CH3 actual current value (X.XXX), CH4 actual current value (X.XXX), CH5 actual current value (X.XXX) XXX) OUTPut command The OUTPut command is used to set and check the output.
-
Page 21: Certification And Quality Assurance
Set power supply CH1 channel as selected channel. INSTrument? This command is used to check which channel is the selected channel. Example: INST? Return parameter: selected channel of power supply (1|2|3|4|5) Safety Do not install substitute parts on the instrument by yourself or perform any unauthorized modification. Please send the instrument to our company's maintenance department for repair to ensure that it can be used safely. - Page 22 Quality Assurance Limits The above guarantee does not apply to damage caused by the following conditions: Customer's incorrect or inappropriate repair of the product; Customers use other software or interfaces; Unauthorized modification or misuse; Operate this product outside the designated environment, or perform configuration and maintenance at a non-designated maintenance place.
Need help?
Do you have a question about the MPS-3035 and is the answer not in the manual?
Questions and answers