Advertisement

Samebike LO26 Manual

Product components

Product components

  1. SADDLE
  2. SEAT POST
  3. MOTOR
  4. WHEEL CHAIN
  5. CRANKSET
  6. PEDALS
  7. SUSPENSlON
  8. FOLDER
  9. BATTERY
  10. MIDDLE LCD DISPLAY WITH USB( LED FOR STANDARD VERSION )
  11. STEM
  12. FRONT LIGHT
  13. SUSPENSlON FRONT FORK
  14. KlCKSTAND
  15. FRONT LIGHT

Folding Method of Product

  1. Adjust the saddle tube and crank, loosen the saddle tube clamp with quick release. Insert the saddle tube down to the bottom and lock the saddle tube clamp with quick release. Adjust the crank Angle to 9 0 'clock and fold the pedals at the same time.
  2. Folding frame. Open the frame folding with safety clasp. Fold the left and right sides of the frame.
  3. Open the folder of the frame, make the front wheel fold nearly parallel to the rear wheel, and finish the folding of bike.

Method of Product assembly

Tools preparation

  1. Tools
  1. Manual
  2. Charger

Packing list (All gifts styles and colors are sent randomly and cannot be used as the reason for return)

Install handlebar and adjust seat tube

  1. Use tools to loosen screws from fasteners
  2. Adjusting the position of handlebar.
  3. Fastening the handlebar
  1. Tighten the screws
  1. Push the saddle down
  2. Open the folder of the seat tube
  3. Adjust and rotate the seat
  1. Finally Lock the folder

Mounting pedal

  1. This bike provides convenient accessories, please Check the L and R marks on pedals.
  1. Take wrench from tool box
  1. R means it should be install in right side, L means it should be install in left side
  2. Tighten the nut counterclockwise

Installing the front wheel

  1. Fixed well front fork.
  1. The front fork is aligned to both ends of the bearing. The disc brake is on the left.
  1. Install the quick release and nut, then tighten well.
  1. After tightening.break the wrench upward and check the operation of the wheel.

Installation of the fenders and headlight

  1. Front and rear fenders.
  1. Fixed the front fender and headlight on the front fork screw hole.
  1. Tighten the screws to position the front fender and headlight,
  1. Place the rear fender at the seat post clip.
  1. Put the Screw in the seat post clip.
  1. Install the quick release and nut, then tighten well.

The method of removing the battery

( The battery of Standard version can't be removed )

  1. Open the folder
  2. Loosen the folder
  1. Insert the key to battery lock
  2. Remove the battery

Product instruction

Charging method

Picture 1 (Charging method of electric bikes with unmovable batteries)

  1. Take out the battery charger
  1. Charger hole is on the left side of the frame and near the folder
  1. Plug the charger into power supply
  1. Red Light shows the battery is charging, green light is full

Picture 2 (Charging method of electric bikes with removable batteries)

  1. Take out the battery charger
  1. You can take battery to your company or home to charge it
  2. Plug one end of the char er into the battery the other Blue into the power supply.
  1. Red Light shows the battery is charging, green light is full

LCD Display ( functional instruction)

Functions

  1. Display
    Speed Display, Battery Level Display, Error Indication, Total Mileage, Single Mileage
  2. Control and Settings
    Power Switch, Front light switch, Wheel Diameter Setting, Maximum speed setting, Idleness Time Setting for Auto-Hibernation, Backlight Brightness Setting, Voltage Level Setting and so on
  3. Communications Protocol: UART
    Display Readings (display at start for 1 second)

    Display Details
    1. Light
    2. Battery Level

    3. Multi-Functions Display
      Total Mileage: ODO,Single Time Mileage: TRIP,Single Riding Time: TIME Current Voltage: VOL,Running current: CUR,DST (Temporary unused)
    4. Vehicle Mode
      Power: Strong Power Mode
    5. Speed Display
      Max Speed: MAX Average Speed: AVG Measuring Unit: MPH or KM/H The speed signal is generated from the Hall signal in the motor and is sent to the panel by the controller. The panel will calculate the actual traveling speed based on the wheel diameter and signal data (number of magnet steel is needed for Hall motors).
    6. Vehicle Status Display
      6 KM/H booster Assist
      Constant speed service
      Electric Assisted mode
      BATT LED
      Brake Indicator
      Controller Failure
      Motor Failure
      Throttle Failure
  1. Introduction of Keys
    Long press ON/OFF to tum off the panel when it's on. Short press the up key + to increase the PAS level, short press the down key - to decrease the PAS level.
    Specific operation
    1. Short press the key "+" to increase the PAS level, short press the down key " - to decrease the PAS level.
      Short press PAS lever increase one lever
      Short press PAS lever decrease one lever
    2. Change the ways of speed display
      Long press change the ways of speed display
  1. The way to open the front light
    Long press open the front light
  2. Turn on / Off the LCD display
    Long press To Turn on / off the display

Notes

  1. Before riding, please read the (User's Manual) carefully. Please check whether the parts in good condition to ensure the safety of your riding.
  2. Please check the status of the vehicle. Please check the brake, wheel, handlebar, folding buckle, quick release part of the electric bike to make sure the electric bike has good status.
  3. Please check the electrical system: To know whether the battery power is enough. if it is not enough, you need charge it as soon as possible.
  4. Please check whether the brake system works properly. If it doesn't work properly, please stop using it, please contact the official customer service person.
  5. Install pedals: if you buy a new products. you need to install pedals by yourself. The pedals are divided into left and right sides. The "R" means the Right pedal. the "L means the Left pedal. and then tighten them counterclockwise-Remember it should be counterclockwise

Important warning

  • This manual include important safety performance information and service information. Please make sure you have read the following warning content before the first time you use our product.
  • If you borrow your electric bicycle to other people, please let the user read this manual, it could help to decrease the risk of accident.
  • Please wear a suitable and safe helmet before riding, please wear the clothes with fluorescent and reflective stripes when you ride at night. Don't exceed speed limit, it is a main reason of traffic accident, we should abide by the traffic rule, we shouldn't exceed the speed limit.
  • Don't touch the charging hole on the bike, or use metal touch it, otherwise, the accident will be caused by the transient short circuit of the current.
  • Zero staring, braking frequent, driving against the wind, carrying people or anything, insufficient air pressure on the tires. All of these will use much electric energy, and then reduce the endurance mileage. If you want the best endurance mileage, please do something as follows:
    1. please use assist mode.
    2. on the premise of safety, don't brake frequently or use zero starting.
    3. Don't overload.
    4. Before riding, please check the pressure of the tire, and supply enough pressure.
  • Our Ebike should avoid prolonged exposure to the sun or rain, avoid storage in places with high temperature or corrosive gas, so as to avoid electroplating parts and paint surface by chemical corrosion and electrical parts damage, resulting in operational failure and accidents
  • Your current insurance business may not cover the situation you may encounter when riding a electric bike, please contact your insurance company or insurance broker for relevant consultation
  • According to the law in China, riding an electric bicycle or a three-wheeled Electric bike must reach the age of 16. If you use this product in other countries, please refer to the local laws and regulations.
  • Bicycles are vehicles with certain risk fact factor, please be sure to abide by the traffic rules.
    At the same time, when emergency braking, brake the rear wheel first, then brake the front wheel, when cycling speed is too fast. There is a danger of tipping over if you brake the front wheel suddenly, please ride carefully.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Samebike LO26 Manual

Advertisement

Need help?

Need help?

Do you have a question about the LO26 and is the answer not in the manual?

Questions and answers

Table of Contents