Braun 7 Series, 5694 Manual
Also See for 7 Series:

Advertisement

Braun 7 Series, 5694 Manual

Description

Overview

Clean & Renew station

  1. Cleaning fluid display
  2. Lift button for cartridge exchange
  3. Station-to-shaver contacts
  4. Start button
  5. Cleaning program indicators
  6. Station power socket
  7. Cleaning cartridge

Shaver

  1. Foil & Cutter cassette
  2. Cassette «release» button
  3. Shaver head «lock» switch
  4. Pop-out long hair trimmer
  5. On/off switch
  6. (–) setting button (sensitive)
  7. (+) setting button (intensive)
  8. Reset button
  9. Shaver display
  10. Shaver-to-station contacts
  11. Shaver power socket
  12. Travel case
  13. Special cord set

Before shaving

Prior to first use you must connect the shaver to an electrical outlet using the special cord set or alternatively proceed as below.

Installing the Clean&Renew station

  • Using the special cord set , connect the station power socket to an electrical outlet.
  • Press the lift button to open the housing.
  • Hold the cleaning cartridge down on a flat, stable surface (e.g. table).
  • Carefully remove the lid from the cartridge.
  • Slide the cartridge into the base of the station as far as it will go.
  • Slowly close the housing by pushing it down until it locks.

The cleaning fluid display will show how much fluid is in the cartridge:

up to 30 cleaning cycles available
up to 7 cleaning cycles remaining
new cartridge required

Charging and cleaning the shaver

Insert the shaver head down into the cleaning station. The contacts on the back of the shaver will align with the contacts in the cleaning station.

The shaver needs to be dry and free from any foam or soap residue!

If required, the Clean&Renew station will automatically charge the shaver. The hygiene status of the shaver will also be analyzed and one of the following cleaning program indicators 5 will light up:

shaver is clean
short economical cleaning required
normal level of cleaning required
high intensive cleaning required

If the station selects one of the required cleaning programs, it will not start unless you press the start button . For best shaving results, we recommend cleaning after each shave.

Whilst cleaning is in progress, the respective cleaning program indicator will blink. Each cleaning program consists of several cycles, where cleaning fluid is flushed through the shaver head and a heat drying process dries the shaver. Depending on the program selected the total cleaning time will range from 32 to 43 minutes.

The cleaning programs should not be interrupted. Please note that whilst the shaver is drying, the shaving head may be hot and wet. When the program is fi nished, the blue indicator will light up. Your shaver is now clean and ready for use.

Stand-by mode

10 minutes after completing the charging or cleaning session, the Clean&Renew station switches to the stand-by mode: The indicators of the Clean&Renew station turn off.

Shaver display

The green indicator fl ashes when the shaver is being charged or when in use.
When the battery is fully charged, the charge segment will light up continuously provided that the shaver is switched on or connected to an electrical outlet.

Some minutes after completing the charging, the shaver switches to the stand-by-mode: The display turns off.

Low charge indicator:
The red indicator fl ashes when the battery capacity has dropped below 20%, provided the shaver is switched on. The remaining capacity will then be sufficient for 2 to 3 shaves.

Charging information

  • A full charge provides up to 50 minutes of cordless shaving time. This may vary according to your beard growth.
  • Recommended ambient temperature for charging is 5°C to 35°C. The battery may not charge properly or at all under extreme low or high temperatures. Recommended ambient temperature for shaving is 15°C to 35°C. Do not expose the appliance to temperatures higher than 50°C for extended periods of time.

Using your shaver

Personalizing your shaver

With the (–) and (+) buttons you can choose the best setting for shaving different areas of your face and as per your specific needs.
The different settings are indicated by the pilot light incorporated in the on/off switch :

  • dark blue (powerful shave)
  • light blue (normal)
  • white (for a thorough comfortable shave in sensitive areas of your face such as neck)

For a thorough and fast shave we recommend the «+» setting.
When switching on next time, the last used setting will be activated.

How to use

Press the on/off switch to operate the shaver:

  • The pivoting shaver head and floating foils automatically adjust to every contour of your face.
  • To shave hard to reach areas (e.g. under the nose) slide the shaver head «lock» switch the back position to lock the pivoting head at an angle.
  • To trim sideburns, moustache or beard, slide the pop-out long hair trimmer upwards.

Tips for the perfect dry shave

For best shaving results, Braun recommends you follow 3 simple steps:

  1. Always shave before washing your face.
  2. At all times, hold the shaver at right angles (90°) to your skin.
  3. Stretch your skin and shave against the direction of your beard growth.

Shaving with the cord

If the shaver has run out of power (discharged), and you do not have the time to recharge it in the Clean&Renew station, you may also shave with the shaver connected to an electrical outlet via the special cord set.

Cleaning

Automatic cleaning

After each shave, return the shaver to the Clean&Renew station and proceed as described above in the section «Before shaving». All charging and cleaning needs are then automatically taken care of. With daily use, a cleaning cartridge should be sufficient for about 30 cleaning cycles.
The hygienic cleaning cartridge contains alcohol, which once opened will naturally evaporate slowly into the surrounding air. Each cartridge, if not used daily, should be replaced after approximately 8 weeks.
The cleaning cartridge also contains lubricants, which may leave residual marks on the outer foil frame after cleaning. However, these marks can be removed easily by wiping gently with a cloth or soft tissue paper.

Manual cleaning

Rinsing the shaver head under running water is an alternative way to keep the shaver clean, especially when travelling:

  • Switch on the shaver (cordless) and rinse the shaver head under hot running water until all residues have been removed. You may use liquid soap without abrasive substances. Rinse off all foam and let the shaver run for a few more seconds.
  • Next, switch off the shaver, press the «release» button to remove the Foil & Cutter cassette and let it dry.
  • If you regularly clean the shaver under water, then once a week apply a drop of light machine oil on top of the Foil & Cutter cassette.

Alternatively, you may clean the shaver using a brush:

  • Switch off the shaver. Remove the Foil & Cutter cassette and tap it out on a fl at surface. Using the brush, clean the inner area of the pivoting head. However, do not clean the cassette with the brush as this may damage it.

Cleaning the housing

From time to time clean the housing of the shaver and the Clean&Renew station with a damp cloth, especially inside the cleaning chamber where the shaver rests.

Replacing the cleaning cartridge

After having pressed the lift button to open the housing, wait for a few seconds before removing the used cartridge to avoid any dripping.
Before discarding the used cartridge, make sure to close the openings using the lid of the new cartridge, since the used cartridge will contain contaminated cleaning solution.

Keeping your shaver in top shape

Replacing the Foil & Cutter cassette/reset
To maintain 100% shaving performance, replace the Foil & Cutter cassette , when the replacement symbol lights up on the shaver display after about 18 months or when cassette is worn.

The replacement symbol will remind you during the next 7 shaves to replace the Foil & Cutter cassette. Then the shaver will automatically reset the display.

After you have replaced the Foil & Cutter cassette, use a ball-pen to push the reset button for at least 3 seconds to reset the counter. While doing so, the replacement light blinks and goes off when the reset is complete. The manual reset can be done at any time.

Accessories
Available at your dealer or Braun Service Centres:

  • Foil & Cutter cassette 70S
  • Cleaning cartridge Clean&Renew CCR


Your shaving system is provided with a special cord set, which has an integrated Safety Extra Low Voltage power supply. Do not exchange or tamper with any part of it, otherwise there is risk of an electric shock. Only use the special cord set provided with your appliance.
Do not shave with a damaged foil or cord.
The shaver head is suitable for cleaning under running tap water. Detach the shaver from the power supply before cleaning the shaver head in water.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the safe use of the appliance and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 years and supervised.
To prevent the cleaning fluid from leaking, ensure that the Clean&Renew station is placed on a fl at surface. When a cleaning cartridge is installed, do not tip, move suddenly or transport the station in any way as cleaning fluid might spill out of the cartridge. Do not place the station inside a mirror cabinet, nor over a radiator, nor place it on a polished or lacquered surface.
The cleaning cartridge contains a highly flammable liquid so keep it away from sources of ignition. Do not smoke near the station. Do not expose to direct sunlight for long periods of time.
Do not refill the cartridge and use only original Braun refill cartridges.

VICTORIA & TASMANIA
Statewide Services Pty Ltd trading
as J A Appliances
17-19 Hossack Avenue
Coburg North, VIC 3058
Tel. (03) 8371 9100
Fax. (03) 9355 8644
Email: jaappliances@statewideservices.com.au

QUEENSLAND

Walters Import trading as Brisbane
Appliance Service Centre
449 Beaudesert Road
Moorooka QLD 4105
Tel. (07) 3277 0360
Fax. (07) 3274 2909
Email: basc@waltersimport.com.au

WESTERN AUSTRALIA

Mark 1 Appliances
Unit 1, 46 Abernethy Road
Belmont, WA 6104
Tel. (08) 9475 0911
Fax. (08) 9475 0922
Email: mark1app@iinet.net.au

NEW SOUTH WALES & ACT
Faulder Appliance Services Pty Ltd
Shop 4,
9 Evans Road,
Rooty Hill, NSW 2766
Tel. (02) 9625 3064
Fax. (02) 9625 3037
Email: fas16@bigpond.com

SOUTH AUSTRALIA & NT
Adelaide Service Centre
Shop B2,
Parkholme Shopping Centre
319 Oaklands Road, Parkholme
Adelaide, SA 5043
Tel. (08) 8357 5800
Fax. (08) 8357 5833
Email: ascpkh@adam.com.au

NEW ZEALAND
Key Service Ltd
7D Echelon Place East Tamaki
Manukau City
Auckland, New Zealand
(PO Box 38569, Howick, Auckland, New Zealand)
Tel. (09) 916 0960
Fax. (09) 916 0970
Email: key-service-ltd@xtra.co.nz

www.braun.com

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Braun 7 Series, 5694 Manual

Advertisement

Need help?

Need help?

Do you have a question about the 7 Series and is the answer not in the manual?

Questions and answers

Table of Contents