Related Manuals for Hyundai HM12V2A
Summary of Contents for Hyundai HM12V2A
- Page 1 CORDLESS GRINDER HM12V2A ORIGINAL INSTRUCTIONS WARNING: READ THE FOLLOWING INSTRUCTIONS BEFORE USING THIS MACHINE.
-
Page 2: Table Of Contents
CONTENTS 1. INTENDED USE 2. SAFETY INSTRUCTIONS 3. EXPLANATION OF SYMBOLS 4. YOUR PRODUCT 5. TECHNICAL DETAILS 6. OPERATION 7. CLEANING AND MAINTENANCE 8. STORAGE 9. DISPOSAL 10. DECLARATION OF CONFORMITY 11. WARRANTY 12. PRODUCT FAILURE 13. WARRANTY EXCLUSIONS... -
Page 3: Safety Instructions
1. INTENDED USE The tool is designed to cut and cut wood or other materials in straight cutting lines while resting firmly on the workpiece. It is not designed for commercial use. WARNING! For your own safety, read this manual and the general safety instructions carefully before using the appliance. - Page 4 c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on.
-
Page 5: Safety Instructions For All Operations
g) Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire. 6) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. -
Page 6: Further Safety Instructions For All Operations
k) Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory. l) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control. -
Page 7: Additional Safety Instructions For Cutting-Off Operations
of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter. e) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges. - Page 8 are required. If a guard is supplied with the tool never use the tool without such a guard. For tools intended to be fitted with threaded hole wheel, ensure that the thread in the wheel is long enough to accept the spindle length. Ensure that ventilation openings are kept clear when working in dusty conditions.
-
Page 9: Explanation Of Symbols
sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning ... -
Page 10: Your Product
4. YOUR PRODUCT On / OFF switch Wheel guard for cutting 11. Direction of rotation arrow Hand grip area Cutting discs on motor Battery release button Clamp bolt with washer 12. Speed controls Li-ion battery pack Hexagon tool 13. battery level indicator Shaft lock button 10. -
Page 11: Technical Data
15. Charger indicator light 5. TECHNICAL DATA Rated voltage (direct current) 12V d.c. Rotation speed 12000-19500/min Max. disc diameter: Ø 85mm Drive spindle thread: Battery type DC33, 12V d.c. 2000mAh, 24Wh Li-ion battery Charger type DC122400, Input 220-240V~, 50-60Hz, 50W, output 12V d.c., 2.4A Pression acoustique =75.6 dB(A), K= 3 dB(A) Puissance acoustique... - Page 12 This will extend the life of your batteries. 6.2 INSTALLING THE BATTERY PACK (FIG. D2) Warning! Always remove battery pack from your tool when you are assembling parts, making adjustments, cleaning, carrying, transporting or when not in use. Removing battery pack will prevent accidental starting that could cause serious personal injury.
- Page 13 Hold the handle firmly and switch on. Avoid blocking the ventilation slots with your hand, as this may cause the grinder to overheat. Let the disc reach full speed at horizontal and vertical. Apply the grinder to the item. Maximum effect is achieved when the grinder is held at an angle of 15-30°in relation to the item.
-
Page 15: Cleaning And Maintenance
7. CLEANING AND MAINTENANCE Always disconnect the battery pack from the angle grinder before making any adjustment or attaching any accessories. 6.1 Cleaning Keep the ventilation slots of the machine clean to prevent overheating of the engine. Regularly clean the machine housing with a soft cloth, preferably after each use. ... -
Page 16: Disposal
10. DELARATION OF CONFORMITY BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux - France, declares that, Product: Cordless Grinder Trade mark: HYUNDAI Model: HM12V2A Serial number: 20210629808-20210632932 is in conformity with the essential requirements and other relevant provisions of the applicable European Directives, based on the application of European harmonized standards. -
Page 17: Warranty
11. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 18: Product Failure
12. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 19: Warranty Exclusions
13. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...
Need help?
Do you have a question about the HM12V2A and is the answer not in the manual?
Questions and answers