hager WYT11xQB Quick Start Manual

§
Safety instructions
Electrical equipment must only be installed
and assembled by a qualifi ed electrician in
accordance with the relevant installation
standards, regulations, directives and safety
and accident prevention directives of the
country.
Failure to comply with these instructions
may result in damage to the device, fi re or
other hazards.
Button cells do not belong in children's
hands! If button cells are swallowed, seek
immediate medical assistance.
Danger of explosion! Do not throw batteries
in fi re.
Danger of explosion! Do not recharge batte-
ries.
The radio transmission is not suitable for
safety or alarm applications.
These instructions are an integral compo-
nent of the product and must be retained by
the end user.
1
WYT11xQB, WYT12xQB,
WYT11xQS, WYT12xQS
Radio wall-transmitter
§
1gang/2gang fl at quicklink
Radio wall-transmitter
1gang/2gang fl at solar quicklink
Bouton poussoir RF
¢
1 voie/2 voies quicklink
Bouton poussoir RF solaire
1 voie/2 voies quicklink
Design of the device
(2)
(3)
(6)
(5)
(8)
(2)
(4)
(7)
(5)
Figure 1: Design of the device
(1) Supporting plate
(2) Frame (not in scope of delivery)
(3) Example: radio wall-transmitter 1gang fl at solar
quicklink
(4) Example: radio wall-transmitter 2gang fl at
quicklink
(5) Screw for dismantling protection
(6) Button design cover 1gang
(7) Button design cover 2gang
(8) Transmission status LED
Function
System information
This device is a product of the quicklink system, in
which installation devices communicate via radio
signals.
quicklink stands for a confi guration mode in which
the function-related connection between transmitters
and receivers is set on the device via push-buttons
and displays without further tools.
All devices confi gurable via quicklink can be opera-
ted together in one system.
This device is compliant to the R&TTE-Directive
1999/5/EG. The Declaration of Conformity and fur-
ther system information can be found on our home-
page www.berker.de.
The device may be used in all EU and EFTA coun-
tries.
Correct use
- Flat surface installation and extension of combi-
(1)
- Only suitable for use in indoor areas, no drip or
- The device has been laid out for smaller applica-
Product characteristics
- Functions for remote control, scenes, control cir-
- Transmission status LED as indication of radio
(1)
Operation
Allotted channel input of wall-transmitter
(8)
The push-button operation areas are freely confi gu-
rable; operation is dependent on the confi guration
(Table 3).
 Press a push-button operation area, e.g. 1, to
Transmission status LED display
After operation, the transmission status LED on the
1gang wall-transmitter lights up through a lens and
on the 1gang wall-transmitter and on the 2gang wall-
transmitter, through the gap between the two push-
buttons.
Transmission
status LED
Blinking orange
Blinking green /
blinking green
1 x blinking green Radio command sent to timer
1 x blinking green
/ 1 x blinking red
Red, fl ickering for
2 seconds
nations.
spray water.
tions in which a maximum of 20 devices are allo-
cated.
cuits via radio signals.
reception; where appropriate, indication of low-
battery status or missing confi guration.
1
2
Transmit radio command
send a radio command.
The transmission status LED (8) lights up to con-
fi rm.
Meaning
Button not confi gured
Radio command sent / radio
command received
Radio command sent / radio
command not received (at
least 1 device)
Battery low; replace
Table 1
1 3
2 4