Subscribe to Our Youtube Channel
Related Manuals for Vacon CX
Summary of Contents for Vacon CX
- Page 1 V A C O N C X / C X L / C X S F R E Q U E N C Y C O N V E R T E R S I / O - e x p a n d e r b o a r d i n s t a l l a t i o n m a n u a l ( Va c o n C X / C X L - r a n g e ) Subject to changes without notice.
-
Page 2: Table Of Contents
I/ O - ex pa nder boa rd insta lla tion (Va con CX/ CXL- ra nge) V a con Page 1 (1 0 ) CO N TEN TS 1 G EN ERA L........... 2 1.1 Vacon CX1 0 0 O PT ....... 2 1.2 Vacon CX1 0 1 O PT ....... -
Page 3: Era L
V a con G EN ERA L Va con CX1 0 0 O PT The available I/ O can be increased by using the Vacon CX1 0 0 O PT I/ O -expander board: - 5 digital inputs (standard signals) -
Page 4: Vacon Fieldbus Boards
- Vacon CX 2 0 3 O PT (Lo nW o rks) The LonW orks fieldbus board (Vacon CX 2 0 3 O PT) must be installed in a separate external option board box. M ore information can be found in the I/ O -expander board installation manual for CXS range. -
Page 5: N Sta Llati O N
I/ O - ex pa nder boa rd insta lla tion (Va con CX/ CXL- ra nge) Page 4 (1 0 ) V a con I N STA LLATI O N 3.1. G enera l Check that your have received all the required parts (figure 3 -1 ):... -
Page 6: Installation
Install the jumper removed from terminal X4 of the control board on terminal X9 of the I/ O - expander board. N ote: the jumper can be connected in O N or O FF position, see Vacon CX/ CXL/ CXS User's M anual, Chapter 6 .2 .2 . Tighten up the earthing screw (5 ) . - Page 7 I/ O - ex pa nder boa rd insta lla tion (Va con CX/ CXL- ra nge) Page 6 (1 0 ) V a con M ount the terminal strip (8) on the same bus bar as the control strip according to the figure on the right.
-
Page 8: Co N Tro Lco N N Ectio N S
I/ O - ex pa nder boa rd insta lla tion (Va con CX/ CXL- ra nge) V a con Page 7 (1 0 ) CO N TRO L CO N N ECTIO N S Va con CX1 0 0 O PT... -
Page 9: Vacon Cx 1 0 1 O Pt
I/ O - ex pa nder boa rd insta lla tion (Va con CX/ CXL- ra nge) Page 8 (1 0 ) V a con 4 . 2 Va con CX1 0 1 O PT T erminal Signal Description +24V Control voltage output Voltage for switches, etc. -
Page 10: Vacon Cx 1 0 2 O Pt
I/ O - ex pa nder boa rd insta lla tion (Va con CX/ CXL- ra nge) V a con Page 9 (1 0 ) 4 . 3 Va con CX1 0 2 O PT T erminal Signal Description +1 0 V Reference output Voltage for a potentiometer, etc. -
Page 11: Vacon Cx 1 0 3 O Pt
I/ O - ex pa nder boa rd insta lla tion (Va con CX/ CXL- ra nge) Page 1 0 (1 0 ) V a con 4 . 4 Va con CX1 0 3 O PT T erminal Signal Description... - Page 12 V ACON PLC P.O. Box 25 Runsorintie 5 FIN-65381 VAASA FINLAND Phone: +358-201 2121 Distributor: Fax: +358-201 212 205 Service: +358-40-8371 150 E-mail: vacon@vacon.com http://www.vacon.com...
Need help?
Do you have a question about the CX and is the answer not in the manual?
Questions and answers