Table of Contents
Related Manuals for Vacon CXS Series
Summary of Contents for Vacon CXS Series
- Page 1 V A C O N C X / C X L / C X S F R E Q U E N C Y C O N V E R T E R S I / O - e x p a n d e r b o a r d i n s t a l l a t i o n m a n u a l ( V a c o n C X S - r a n g e ) Subject to changes without notice.
-
Page 2: Table Of Contents
1.4 Vacon CX103OPT ...... 2 1.5 Vacon CX104OPT ...... 3 1.6 Vacon fieldbus boards ....3 2 S P E C I F I C AT I O N S ......4 3 I N S TA L L AT I O N ......... 5 3.1 General ........ -
Page 3: E N E R A L
I/O-expander board installation (Vacon CXS-range) G E N E R A L Due to the compact frame size of the Vacon CXS series all I/O-expander boards need to be installed in a separate box (Vacon CXSOPTBKIT), except the smaller, specifically for Vacon CXS designed boards (Vacon CX104OPT, CX105OPT, CX107OPT, CX108OPT). -
Page 4: Vacon Cx104Opt
Typical use: Closed Loop Vector Control Fieldbus boards Vacon fieldbus boards can be installed in the Vacon CXS range frequency converters as I/O-expander boards. The needed information to install/commission fieldbus boards can be found in the respective Vacon fieldbus manual. -
Page 5: P E C I F I C At I O N S
Va c o n Page 4 (15) I/O-expander board installation (Vacon CXS-range) SPECIFICATIONS Safety Fulfills EN50178, C-UL and EN60204-1 standards ≥ 200 kΩ Control Analogue voltage, input 0—± 10 V, R = 250 Ω connections Analogue current, input 0(4)—20 mA, R 24 V: "0"... -
Page 6: N S Ta L L At I O N
Before doing any commissioning, carefully read the safety instructions in the "USER'S MANUAL, VACON CX/CXL/CXS", Chapter 1, SAFETY. Disconnect the frequency converter from the mains. NOTE: Also the control circuits! Wait further 5 minutes before opening the cover of the frequency converter. Verify by measuring that the frequency converter is safe to touch. -
Page 7: Installation
Va c o n Page 6 (15) I/O-expander board installation (Vacon CXS-range) INSTALLATION I/O-repeater board (1) should be installed above the control board inside the frequency con- verter. The I/O-expander board (10) and I/O-interface board (11) should be installed in the option box. - Page 8 Va c o n Page 7 (15) I/O-expander board installation (Vacon CXS-range) Connect the shielded data cable for I/ O-repeater board (2) to the control board terminal X14. Install the control panel cover with 4 screws. Set the protection foil (6) above the I/O-repeater board as shown in the picture. Make sure that the protection foil is correctly located, push the "arms"...
- Page 9 Close the cover of the frequency converter. Install the jumper removed from the control board X4 terminal into the I/O-expander board terminal X9. Note: the jumper can be connected in ON or OFF position,see Vacon CX/CXL/ CXS User's manual, Chapter 6.2.2.
- Page 10 Before connecting the mains make sure that the cover of the option box and frequency con- verter are closed. Set the parameters of I/O-expander board according to the Vacon "Five in One+" -applica- tion manual (parameter group 3). Table 3-2.
- Page 11 Va c o n Page 10 (15) I/O-expander board installation (Vacon CXS-range) Figure 3-2. Frequency converter and external I/O-expander box installation (unit sizes M3 and M4B). I/O-expander box can also be installed beside the frequency converter (unit sizes M3, M4B and M5B).
-
Page 12: Control Connections
RO4/1 Relay output 4 RO4/2 RO5/1 Relay output 5 FAULT RO5/2 Figure 4-1 Control connections of Vacon CX100OPT. *) NOTE! Thermistor input (terminals 221 and 222) must be shorted if not used. Vacon Plc Tel: +358-201 2121 Fax: +358-201 212 205... -
Page 13: Vacon Cx101Opt
Thermistor input motor thermistors *) T I + RO4/1 Relay output 4 RO4/2 Figure 4-2 Control connections of Vacon CX101OPT. *) NOTE! Thermistor input (terminals 221 and 222) must be shorted if not used. Vacon Plc Tel: +358-201 2121 Fax:... -
Page 14: Vacon Cx102Opt
RO4/1 Relay output 4 RO4/2 RO5/1 Relay output 5 FAULT RO5/2 Figure 4-3 Control connections of Vacon CX102OPT. *) NOTE! Thermistor input (terminals 221 and 222) must be shorted if not used. Vacon Plc Tel: +358-201 2121 Fax: +358-201 212 205... -
Page 15: Vacon Cx103Opt
RO4/1 Relay output 4 RO4/2 RO5/1 Relay output 5 FAULT RO5/2 Figure 4-4 Control connections of Vacon CX103OPT. *) NOTE! Thermistor input (terminals 221 and 222) must be shorted if not used. Vacon Plc Tel: +358-201 2121 Fax: +358-201 212 205... -
Page 16: Vacon Cx104Opt
Va c o n Page 15 (15) I/O-expander board installation (Vacon CXS-range) Vacon CX104OPT More information on the Vacon CX104OPT encoder option board you will find in a separate manual (ud318). Ask your distributor for more information. Terminal Signal Description... - Page 17 V ACON PLC P.O. Box 25 Runsorintie 7 FIN-65381 VAASA FINLAND Phone: +358-201 2121 Distributor: Fax: +358-201 212 205 Service: +358-40-8371 150 E-mail: vacon@vacon.com http://www.vacon.com...
Need help?
Do you have a question about the CXS Series and is the answer not in the manual?
Questions and answers