Asus ROG STRIX G15DS Service Manual
Asus ROG STRIX G15DS Service Manual

Asus ROG STRIX G15DS Service Manual

Hide thumbs Also See for ROG STRIX G15DS:

Advertisement

Quick Links

Desktop ROG STRIX G15DS
Service Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ROG STRIX G15DS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Asus ROG STRIX G15DS

  • Page 1 Desktop ROG STRIX G15DS Service Manual...
  • Page 2 INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR INTHIS MANUAL OR PRODUCT.
  • Page 3 ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement. This limit also applies to ASUS' suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.
  • Page 4 Disclaimer ASUS is not responsible for direct, indirect, intentional or unintentional damages resulting from improper installation and operation. Safety precautions • Before handling components, use a grounded wrist strap or touch a safely grounded object to avoid damaging them due to static electricity.
  • Page 5: Table Of Contents

    Table of Contents ⚫ ASUS Desktop ROG STRIX G15DS Overview ⚫ Components Top View ⚫ Components Bottom View ⚫ Components top View (For Glass version) ⚫ Appropriate Tools ⚫ Disassembly steps : • SLIDE DOOR • VGA CARD • DDR CARD •...
  • Page 6: Asus Desktop Rog Strix G15Ds Overview

    ASUS Desktop ROG STRIX G15DS Overview Rear Panel View Front & Top View ❶ Power button ❶ PS/2 keyboard/mouse combo port ❷ Headphone port ❷ HDMI® port (optional) ❸ Microphone port ❸ DisplayPort ❹ USB 3.2 Gen 1 Type-C® port ❹...
  • Page 7: Components Top View

    Components Top View ♦ VGA Card ♦ D700TA M2 ♦ LED CR BD ♦ RFCABLE ASSEMBLY SMA ♦ POWER SW CABLE ♦ POWER SWITCH HOLDER ♦ FIO CABLE RUBBER ♦GA15DH_PSU_GASKET PAD 25X20X7 (Contained in SUB ASSY) CABLE CONDUCTIVE CLOTH ♦ USB CABLE ACETATE ♦...
  • Page 8 Components Top View ♦ AMD RETENTION KITS ♦ GA15DH TOP LED BD ♦ GA15DH SIDE LED BD ♦ D640MB STAND OFF M2*4.6H*4.75D ♦ GLASS LED CABLE ♦ TOP LED BD CAB Back...
  • Page 9: Components Bottom View

    Components Bottom View ♦ VGA Card ♦ WIFI Card ♦ DDR ♦ MAIN BOARD ♦ FRONT IO BD ♦SSD ♦ INTEL RETENTION ♦ LED CR BD KITS Back...
  • Page 10: Appropriate Tools

    Appropriate Tools Please prepare and select the appropriate tools to disassemble/assemble for the ROG Strix (G15DS) desktop. ♦ Screwdriver ♦ Alcohol 95% ♦ Glove ♦ Dust-free Cloth Please accord to different screw specification to choose different screwdriver and head. #1 #2 ♦...
  • Page 11: Slide Door

    SLIDE DOOR Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove screws *4pcs. Screws Spec Torque (kgf-cm) Step 2 : Pull the side doors *2pcs. SCREW #6-32*6.3L (7.3,2.45) 8.0± 0.5 Pull SLIDE DOOR (L) Pull SLIDE DOOR (R) Back...
  • Page 12: Vga Card

    VGA CARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect cables *2pcs (Yellow mark). Screws Spec Torque(kgf-cm) Step 2 : Remove screws *4pcs (Red and Blue mark). SCREW M3*4L (6.3,2.05) (B) #2 6.0±...
  • Page 13: Ddr Card

    DDR CARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Unlock then remove DDR *4pcs. Assembly Notice Please follow the below criteria to assemble DDR. Memory slot 1pcs 2pcs 4pcs DIMM_A1 ● DIMM_A2 ●...
  • Page 14: Cpu Cooler Am4 65W

    CPU COOLER AM4 65W Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect (yellow mark) FAN connector *1pc. Step 2 : Remove GL10DH CPU COOLER AM4 65W. Unlock Loose Remove Back...
  • Page 15: 105W Cooler

    105W COOLER Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Screws Spec Torque (kgf-cm) Step 1: Disconnect (yellow mark) FAN connector *1pc. Step 2: Remove (blue mark) screw *1pc and COOLER FAN. 105W COOLER 6.0± 0.5 Step 3: Remove (red mark) screws *4pcs and G15DS 105W COOLER.
  • Page 16: Sys Fan

    SYS FAN Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect (yellow mark) FAN connector *1pc. Screws Spec Torque (kgf-cm) Step 2 : Remove screws *4pcs on the outside of iron grid. M5*10L (K) B-NI TAPPING 8.0±...
  • Page 17: Front Cover And Led Board

    FRONT COVER AND LED BOARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Tear the (yellow mark) CABLE CONDUCTIVE CLOTH and loose the POWER SW CABLE. Screws Spec Torque (kgf-cm) Step 2 : Pull the latch slightly away. Step 3 : Tear off (red mark) Mylar *2pcs and disconnect the (yellow mark) connectors *3pcs.
  • Page 18: Power Switch

    POWER SWITCH Disassembly Notice Please be sure to pull out AC POWER CORD. Assembly Notice Please follow the steps below to assemble POWER SWITCH HOLDER and Step 1 : Remove POWER SWITCH HOLDER with POWER SW CABLE from front case. Step 2 : Release hooks (green mark) then take out POWER SW CABLE from POWER SWITCH HOLDER.
  • Page 19: Front Bezel Assy

    FRONT BEZEL ASSY FRONT BEZEL Assembly Notice NOTE! Before assembling the FRONT BEZEL ASSY, please carefully read the following assembly instructions . When assembling the LED board, USB cable and power cord on the FRONT BEZEL ASSY, please make sure that the USB cable and power cord do not touch the PIN HEADER of the LED board, otherwise it may cause a short circuit and overheating.
  • Page 20 FRONT BEZEL ASSY FRONT BEZEL Assembly Notice Step-3 After connecting the POWER and USB cable to the LED board, please tidy up the cables in the direction of the yellow arrow and be careful to avoid the PIN HEADER (marked in red). PIN HEADER PIN HEADER Step-4 Check that the cable direction must follow the yellow arrow, paste...
  • Page 21 FRONT COVER AND LED BD FRONT COVER and LED BD Assembly Notice For FRONT COVER and LED BD assembly notice the following. Can't see cables GA15DH FRONT LENS FOIL GA15DH GLASS LED CABLE L:125 Make sure the hook and power button click into place GA15DH USB2.0 CABLE L:750MM G15CX CR BD POWER CABLE Back...
  • Page 22: Main Board With Io Cover & Ssd

    MAIN BOARD with IO Cover & SSD Please be sure to pull out adapter and disconnect the battery. Disassembly Notice Screws Spec Torque (kgf-cm) Step 1 : Disconnect (yellow mark) connectors *6pcs. Step 2 : Remove SSD1/SSD2 screws *4pcs and take out the SSD M2_C HS*2pcs. SCREW M2*7.5L (4.5,0.8) #1 2.0±...
  • Page 23: Main Board

    MAIN BOARD Assembly Notice Please follow the below image to Add sponge *4pcs (red mark)on motherboard DIMM Area(EN-0402703). D700TD MB SPONGE L35 W8 T8//L35 W8 T8...
  • Page 24 MAIN BOARD with Cables Assembly Notice Please follow the instructions to assemble the MB. Back...
  • Page 25: Main Board With Cpu

    MAIN BOARD with CPU Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove the CPU. Step 2 : Remove the BATT-LI CR2032. Lift up Remove Back...
  • Page 26 MAIN BOARD with CPU COOLER & CPU CPU COOLER Disassembly Notice Assembly Notice If the CPU COOLER is hard to disassemble, Please follow the instructions to assemble the CPU. please move the COOLER left and right to separate CPU triangle must be aligned to MB triangle Pin facing down on Processor packaging to protect the CPU.
  • Page 27 MAIN BOARD with CPU COOLER & CPU Assembly Notice Please be sure to pull out adapter and disconnect the battery. Please make sure that re-smear thermal material on CPU Die, if thermal module have to be reassembled. Step-1 : Using dust-free cloth with 95% alcohol to clean up the residual thermal grease on CPU& GPU Die. Step-2 : Please use plastic tool (Plastic stick) to get Thermal Grease, and smear over CPU around 0.2~0.3mm thick.
  • Page 28: Main Board With Wlan

    MAIN BOARD with WLAN Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove screws *2pcs and take out SHIELDING FOR Z690 WIFI. Screws Spec Torque (kgf-cm) Step 2 : Remove screw *1pc and take out the SHIELDING. SCREW M2*4L 2.0±...
  • Page 29: Top Cover

    TOP COVER Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Use the Plastic Blade to Remove the Handle case. Screws Spec Torque (kgf-cm) Step 2 : Remove screws *2pcs located on the end of the Handle. SCREW M2.5*6L (5.5,0.8) (K) #1 3.0±...
  • Page 30: Front Io Board

    FRONT IO BOARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove screws *2pcs. Screws Spec Torque (kgf-cm) Step 2 : Disconnect the USB 3.0 cable and Audio cable. M2.5*4L (K) B-ZN NY #1 3.0±...
  • Page 31: Hdd

    Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove screws *4pcs. Screws Spec Torque (kgf-cm) Step 2 : Disconnect the connectors *2pcs Step 3 : Take out the HDD. SCREW #6-32*6L(7.1,2.3) (B) #2 6.5±...
  • Page 32: Power Supply

    POWER SUPPLY Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect the connector *1pc. Screws Spec Torque (kgf-cm) Step 2 : Remove screws *4pcs. SCREW #6-32*L6 (B)B-NI-ZN NY 8.0± 0.5 Step 3 : Take out the POWER SUPPLY. Unscrew Disconnect Back...
  • Page 33: Led Board

    LED BOARD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove screw*2pcs and then disconnect cable *1pc. Screws Spec Torque (kgf-cm) Step 2 : Remove screw*3pcs and then disconnect cable *1pc. SCREW M2.5*4L (K) B-ZN NY 2.5±...
  • Page 34: Cable Assembly

    CABLE ASSEMBLY Assembly Notice Please be sure to pull out adapter and disconnect the battery. Tidy up the cable of the back mainframe as illustrated. Back...

Table of Contents