Vestil EHLTT Series Instructions Manual

Double scissor electric-hydraulic lift tables
Hide thumbs Also See for EHLTT Series:

Advertisement

TABLE OF CONTENTS
EHLTT & EHLTTS-Series Double Scissor Electric-Hydraulic Lift Tables
Receiving Instructions
After delivery, remove the packaging from the product. Inspect the product closely to determine
whether it sustained damage during transport. If damage is discovered, record a complete description of
it on the bill of lading. If the product is undamaged, discard the packaging.
NOTE: The end-user is solely responsible for confirming that product design, use, and maintenance comply
with laws, regulations, codes, and mandatory standards applied where the product is used.
Technical Service & Replacement Parts
For answers to questions not addressed in these instructions and to order replacement parts, labels,
and accessories, call our Technical Service and Parts Department at (260) 665-7586. The Department can
also be contacted online at https://www.vestil.com/page-parts-request.php.
Electronic Copies of Instruction Manuals
Additional copies of this instruction manual may be downloaded from
manuals.php.
Signal
Words..........................................................................................................................
Safety Instructions and Notice about Proper Use and
Complete Unit Exploded Views and Bills of
Electric Circuit
Diagrams: 115VAC; 203-230VAC; 3-Phase..........................................................
Motor Lead
Connections........................................................................................................
Control Voltage
Transformer...................................................................................................
Power Unit
Subassemblies:
Installing the
Table.................................................................................................................
Record of Satisfactory
Condition............................................................................................
Operating the
Table...............................................................................................................
Inspecting and Maintaining the
Solenoid Valve
Maintenance................................................................................................
Bleeding Air from the Hydraulic
Troubleshooting
Guide...........................................................................................................
Labeling
Diagram.........................................................................................................................
Limited
Warranty...................................................................................................................
TABLE OF CONTENTS
Rev. 6/5/2024
Vestil Manufacturing Company
2999 North Wayne Street, P.O. Box 507, Angola, IN 46703
Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868
Web:
www.vestil.com
Table of Contents
Materials................................................................
Power
Unit;
Manifold Assembly; Corresponding Hydraulic
Table.....................................................................................
Cylinder(s)..............................................................................
Copyright 2024 Vestil Manufacturing Co.
Fax: (260) 665-1339
e-mail:
EHLTT Shown
Maintenance............................................
EHLTD MANUAL
info@vestil.com
https://www.vestil.com/page-
Page
12 - 17
Schematic.
19 - 25
25
27
29 - 30
Page 1 of 35
2
2
-
3
4
-
11
18
18
-
27
27
-
29
31
32
33
34
35

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EHLTT Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Vestil EHLTT Series

  • Page 1 For answers to questions not addressed in these instructions and to order replacement parts, labels, and accessories, call our Technical Service and Parts Department at (260) 665-7586. The Department can also be contacted online at https://www.vestil.com/page-parts-request.php. Electronic Copies of Instruction Manuals Additional copies of this instruction manual may be downloaded from https://www.vestil.com/page-...
  • Page 2: Signal Words

    SAFETY INSTRUCTIONS Vestil strives to identify all hazards associated with the use of our products. However, material handling is dangerous and no manual can address every risk. The most effective way to avoid injury is for the end-user to exercise sound judgment whenever using this product.
  • Page 3: Specifications

     Contact the manufacturer for SDS (Safety Data Sheet) documentation SPECIFICATIONS Documents that provide specifications for EHLTT series portable scissor lift tables are available online to anyone who visits Vestil’s website. Specifications include dimensions, net weight, and capacity information. To access the appropriate specifications document, navigate to the EHLTT webpage at https://www.vestil.com/product.php?FID=209.
  • Page 4 TABLE OF CONTENTS Rev. 6/5/2024 EHLTD MANUAL EXPLODED VIEW: EHLTT-3648-1/2/3/4-47 (02-006-333) TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 4 of 35...
  • Page 5 LIMIT SWITCH W/ROLLER ARM 27560 #10-32 x 3/4 LG SLOTTED MACHINE SCREW 36030 10-32 HEX NUT, GRADE 2 01-515-015 SUB-ASSEMBLY, TOE GUARD, 36" X 48", INCLUDES HARDWARE & SWITCHES TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 5 of 35...
  • Page 6 TABLE OF CONTENTS Rev. 6/5/2024 EHLTD MANUAL EXPLODED VIEW: EHLTT-4848-1/2/3/4-47 (02-006-330) TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 6 of 35...
  • Page 7 LIMIT SWITCH W/ROLLER ARM 27560 #10-32 x 3/4 LG SLOTTED MACHINE SCREW 36030 10-32 HEX NUT, GRADE 2 SUB-ASSEMBLY, TOE GUARD, 36" X 48", INCLUDES HARDWARE 01-515-015 & SWITCHES TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 7 of 35...
  • Page 8 TABLE OF CONTENTS Rev. 6/5/2024 EHLTD MANUAL EXPLODED VIEW: EHLTTS-3654-2-48 (02-006-211-001) TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 8 of 35...
  • Page 9 #11 HITCH PIN CLIP, Ø1/8" X 2 5/8 LG 68021 EXTERNAL RETAINING RING, PHOSPHATE FINISH, 1-1/8" 01-022-001 LIMIT SWITCH W/ROLLER ARM SUB-ASSEMBLY, TOE GUARD, 38" X 54", INCLUDES HARDWARE 01-515-044 & SWITCHES TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 9 of 35...
  • Page 10 TABLE OF CONTENTS Rev. 6/5/2024 EHLTD MANUAL EXPLODED VIEW: EHLTTS-3654-4-48 (02-006-221-001) TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 10 of 35...
  • Page 11 #11 HITCH PIN CLIP, Ø1/8" X 2 5/8 LG 68021 EXTERNAL RETAINING RING, PHOSPHATE FINISH, 1-1/8" 01-022-001 LIMIT SWITCH W/ROLLER ARM SUB-ASSEMBLY, TOE GUARD, 38" X 54", INCLUDES HARDWARE 01-515-044 & SWITCHES TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 11 of 35...
  • Page 12: Electric Circuit Diagrams

    115 VAC, Single-Phase without Remote Control Electric Circuit Diagram (02124012 Rev. D) Note: Overcurrent & short circuit protection and disconnect must be provided by end user. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 12 of 35...
  • Page 13 Rev. 6/5/2024 EHLTD MANUAL 115 VAC, Single-Phase with Remote Control Electric Circuit Diagram (02124021) Note: Overcurrent & short circuit protection and disconnect must be provided by end user. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 13 of 35...
  • Page 14 TABLE OF CONTENTS Rev. 6/5/2024 EHLTD MANUAL 208-230 VAC, Single-Phase Electric Circuit Diagram (24124013 Rev. A) Note: Overcurrent & short circuit protection and disconnect must be provided by end user. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 14 of 35...
  • Page 15 Rev. 6/5/2024 EHLTD MANUAL 208-230 VAC, Single-Phase with Remote Control Electric Circuit Diagram (02124022) Note: Overcurrent & short circuit protection and disconnect must be provided by end user. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 15 of 35...
  • Page 16 TABLE OF CONTENTS Rev. 6/5/2024 EHLTD MANUAL 460VAC, 3-Phase Electric Circuit Diagram (02124014 Rev. D) Note: Overcurrent & short circuit protection and disconnect must be provided by end user. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 16 of 35...
  • Page 17 Rev. 6/5/2024 EHLTD MANUAL 460VAC, 3-Phase with Remote Control Electric Circuit Diagram (02124014 Rev. A) Note: Overcurrent & short circuit protection and disconnect must be provided by end user. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 17 of 35...
  • Page 18 Polarity across the thermostat leads is not important. When changing the motor voltage configuration, you must also change the configuration of the control transformer to match the motor voltage. Control Voltage Transformer (01-129-003 Rev. B). TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 18 of 35...
  • Page 19 VALVE, CARTRIDGE, 2 99-153-017 POS., 3 WAY VALVE, PRESSURE 99-153-006 RELIEF, 210 BAR COIL WITH DIN 99-034-008 CONNECTOR O-RING, MANIFOLD, 10 99-144-008 1/2" OD O-RING, MANIFOLD, 11 99-144-009 3/4" OD TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 19 of 35...
  • Page 20 LOCK WASHER, HI COLLAR, 5/16" 33004 FLAT WASHER, USS, ZINC PLATED, Ø1/4" 99-116-030 FITTING, HYDRAULIC, 06MJ-06MORB STRAIGHT 99-116-033 FITTING, HYDRAULIC, 06MJ-06MAORB 90° ELBOW 99-116-044 FITTING, HYDRAULIC, 08MJ-08MORB STRAIGHT TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 20 of 35...
  • Page 21 HYDRAULIC, DO3, 99-153-090 MOTOR CENTER, SOLENOID OPERATED SCREWS, MODIFIED, 5/16"-18 x 1/4" HEX 99-119-012 DRIVE CUP, SOCKET SET SCREW RESERVOIR, FILTER, HYDRAULIC, SPIN-ON, 22-031-007 1"-12 THREAD, 10 MICRON TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 21 of 35...
  • Page 22 VALVE, CARTRIDGE, 2 99-153-017 POS., 3 WAY VALVE, PRESSURE 99-153-006 RELIEF, 210 BAR COIL WITH DIN 99-034-008 CONNECTOR O-RING, MANIFOLD, 10 99-144-008 1/2" OD O-RING, MANIFOLD, 11 99-144-009 3/4" OD TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 22 of 35...
  • Page 23 LOCK WASHER, HI COLLAR, 5/16" 33004 FLAT WASHER, USS, ZINC PLATED, Ø1/4" 99-116-030 FITTING, HYDRAULIC, 06MJ-06MORB STRAIGHT FITTING, HYDRAULIC, 06MJ-06MAORB 90° 99-116-033 ELBOW 99-116-044 FITTING, HYDRAULIC, 08MJ-08MORB STRAIGHT TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 23 of 35...
  • Page 24 LOCK WASHER, HI COLLAR, 5/16" 33004 FLAT WASHER, USS, ZINC PLATED, Ø1/4" FITTING, HYDRAULIC, 06MJ-06MORB 99-116-030 STRAIGHT FITTING, HYDRAULIC, 06MJ-06MAORB 99-116-033 90° ELBOW FITTING, HYDRAULIC, 08MJ-08MORB 99-116-044 STRAIGHT TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 24 of 35...
  • Page 25 Electrical connections shall be performed by a qualified electrician. Before You Begin. The Electric Hydraulic Scissors Lift Table must be anchored to a smooth, level, and adequately strong concrete surface. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 25 of 35...
  • Page 26 DO NOT place a lift table in service if either of these devices isn’t functioning properly. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 26 of 35...
  • Page 27: Operating The Table

    It is intended to lift stable, evenly- distributed, nonhazardous materials loads having a size or footprint approximately the same size as the platform. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 27 of 35...
  • Page 28 (pump motor does not run). Release the pushbutton to stop the descent of the platform. If the perimeter toe guard is activated as the platform descends, the TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 28 of 35...
  • Page 29 Technical Service can be contacted by calling (260) 665-7586 and asking for the Service and Parts Department or by submitting your questions through Vestil’s online parts and service portal at https://www.vestil.com/page-parts-request.php.
  • Page 30 150 SUS at 100°F (ISO 32 cSt @ 40°C) or Dexron transmission fluid. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 30 of 35...
  • Page 31 (illustration). Reinstall the solenoid valve, tightening to 20 lb-ft of torque. Reattach the solenoid coil and the retaining nut. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 31 of 35...
  • Page 32 Bleeder valve Lower the platform until the ends of the maintenance props are 1”-1 ” away from the corners of the base frame. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 32 of 35...
  • Page 33: Troubleshooting Guide

    Flow control valve spool sticking. “Inspecting and Maintaining” section. Platform lowers too Remove and inspect valves. Clean per instructions Flow control valve spool sticking. quickly. “Inspecting and Maintaining” section. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 33 of 35...
  • Page 34: Labeling Diagram

    TECHNICAL SERVICE AND REPLACEMENT PARTS DEPARTMENT online at http://www.vestilmfg.com/parts_info.htm. Alternatively, you may request replacement parts and/or service by calling (260) 665-7586 and asking the operator to connect you to the Parts Department. TABLE OF CONTENTS Copyright 2024 Vestil Manufacturing Co. Page 34 of 35...
  • Page 35: Limited Warranty

    The warranty period for original dynamic components is 1 year. For wearing parts, the warranty period is 90 days. Both warranty periods begin on the date Vestil ships the product to the Warrantee. If the product was purchased from an authorized distributor, the periods begin when the distributor ships the product.

Table of Contents