Page 1
Technical Support and E-Warranty Certificate www.vevor.com/support BICYCLE CARGO TRAILER MODEL: 20315 We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us.
Page 2
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
SAFETY INSTRUCTIONS ⚠ WARNING Failure to comply with the instructions and warnings in this manual could result in serious injury or death of the rider. The trailer is designed exclusively for transporting cargo on road with a standard bicycle. It is intended for personal use only. Only use the trailer as described in the instructions.
Page 4
If the weight is too low, the rear wheel of the bicycle could lose traction. If it is too high the hitch may be overloaded. MODEL AND PARAMETERS Model 20315 Max. Load 88lbs Storage Bin Size 24*15.7*10.6inch(Plastic Box)...
Page 5
CONTENTS 1 x Main frame 2 x Wheels 1 x Cover 2 x Front reflector kits (white) 1 x Tow bar 2 x Rear reflector kits (red) 2 x Side reflector kits (yellow) 1 x Accessory pack 1 x 11mm Wrench +1 x 4mm Hex key+1 x User Manual - 4 -...
Page 6
How to Assemble 1. Installing the reflectors Push to mount the reflector on the clamp. Insert the anti-slip rubber into the hole of the clamp (Figure Figure 1 Open the clamp and mount the clamp on the trailer (Figure 2). Figure 2 Please be careful not to confuse different positions (Figure 3).
Page 7
2. Installing the Tow Bar Take out the crate (Figure 4). Fix the lower part of tow bar to main frame with 56 mm screws and gasket in the accessory pack (Figure 5). Figure 4 Figure 5 Install the pipe sleeve and combine two parts of tow bar together. Fix two parts with 34 mm screws in the accessory pack (Figure 6).
3. Attaching the Wheels Insert wheel axle into axle receiver underneath the trailer frame until it snaps in place (Figure 8). Pull firmly on wheel to confirm the axle is fully engaged (Figure 9). To remove the wheels, press the buttons on the axle receiver and take the wheels out.
Figure 12 Tighten the safety pin to lock the clamp (Figure 13). Tie the safety strap to the seat tube (Figure 14). Figure 13 Figure 14 5. Attaching the Cover Put the cover on the crate. Tie the hook-and-loop fasteners on both sides to the base frame (Figure 15).
Page 10
6. Releasing the Support leg Release the safety pin. Put down the support leg. Fix the safety pin in the lower hole (Figure 16). The support leg is available only when the trailer is used as hand cart. Please lock back the support leg before the trailer is attached to bicycle.
Before You Ride Check before each use: Wheels are properly secured to the trailer. Tires are inflated to recommended pressure on the tire side wall. Tow bar is properly secured to the trailer. Coupler is properly secured to the bicycle. ...
Page 12
Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom Tel: 01772418127 pooledas123@gmail.com Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 Made In China Technical Support and E-Warranty Certificate www.vevor.com/support...
Need help?
Do you have a question about the 20315 and is the answer not in the manual?
Questions and answers