WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. — 2 —...
SECTION 1 SERVICING NOTE ALL CLEAR Adjustment of OSD Screen Position Mode which erases all the user memories registered in this unit and The position of the screen can be adjusted freely to correct the de- sets to setting at shipment. viation of the OSD screen caused by the monitor type that users are using.
5-11. IC PIN FUNCTIONS • IC103 Mode Controller (MB90673PF-G-226-BND) Pin No. Pin Name Function AC MUTE Mute signal output to Rear power amp D. LAT Latch output to Dolby surround processor T. LAT Latch output to Tone controller S. CLK Serial clock output to Dolby surround processor S.
Page 37
Pin No. Pin Name Function MODE 0 Mode setting pin (Fixed at “H”) MODE 1 Mode setting pin (Fixed at “H”) MODE 2 Mode setting pin (Fixed at “L”) STANDBY Standby signal input of hardware STOP STOP signal input LEANING LED LEARNING LED drive signal output —...
Page 38
• IC205 OSD (MB90095PF-G-186-BND) Pin No. Pin Name Function Luminous signal input for superimpose displays (Not used) Chroma signal input for superimpose displays (Not used) Composite signal input for superimpose displays AVCC – Power supply (+5V) (Analog) FSCO Color burst phase signal output VBLK Vertical blanking period output (Not used) –...
Page 39
• IC209 OSD Controller (MB90672PF-G-125-BND) Pin No. Pin Name Function 1, 2 AD14, AD15 Address bus and data bus input/output 3 to 6 A16 to A19 Address bus output Chip Enable output to RC controller (For communication using personal computers) PCLK Clock output to RC controller (For communication using personal computers) Data output to RC controller (For communication using personal computers)
Page 40
Function Pin No. Pin Name Mode setting (Fixed at “H”) MODE 0 Mode setting (Fixed at “L”) MODE 1 Mode setting (Fixed at “L”) MODE 2 Hardware standby (Fixed at “H”) HSTX Request input of reset interrupt STOP IR sensor remote control input (Not used) IR-IN (A6) Not used 47, 48...
Page 41
• IC215 RC Controller (LC86F5864A-5F53) Pin No. Function Pin Name P70/INT0 Chip enable input from OSD controller P71/INT1 Chip enable input (For on-board) (Not used) P72/INT 2/TOIN Not used (Connector to ground) P73/INT 3/TOIN SIRCS signal input Power supply normality signal input Infrared rays transmission data status signal output to OSD controller “L”...
Page 42
Pin No. Pin Name Function P10/SOO Serial data output to OSD controller P11/SI0/SB0 Serial data input to OSD controller P12/SCKO Serial clock input from OSD controller P13/SO1 – Ground P14/SI1 Serial data input (For on-board) (Not used) P15/SCK1 Serial clock input (For on-board) (Not used) P16/BUZ Not used P17/PWM...
SECTION 6 EXPLODED VIEWS NOTE: The components identified by mark ! • Abbreviation • Items marked “*” are not stocked since they are or dotted line with mark ! are critical : German model seldom required for routine service. Some delay for safety.
SECTION 7 5.1 IN ELECTRICAL PARTS LIST Note: • SEMICONDUCTORS • Due to standardization, replacements in the parts list The components identified by mark ! In each case, u: µ , for example: may be different from the parts specified in the or dotted line with mark ! are critical uA...: µ...
Need help?
Do you have a question about the TA-VE810G and is the answer not in the manual?
Questions and answers