1. Manuals
  2. Brands
  3. Lippert Manuals
  4. Lawn and Garden Equipment
  5. Solera 3000XL Series
  6. Installation manual

Lippert Solera 3000XL Series Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
3000XL Series Awning
OEM INSTALLATION MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Solera 3000XL Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Lippert Solera 3000XL Series

Summary of Contents for Lippert Solera 3000XL Series

  • Page 1 3000XL Series Awning OEM INSTALLATION MANUAL...

  • Page 2: Table Of Contents

    tABLe oF CoNteNtS System Information Safety Prior to Installation Resources Required Installation Awning Rail Installation (If Needed) Awning Installation Securing the Fabric Option 1 Option 2 Awning Wiring Installation with Speakers — option Installation with LeD — options LED Roll Tube Installation LED Light Rail Installation Seal Wall Penetrations operation...

  • Page 3: Safety

    Lippert Components Limited Warranty. Note: This manual will refer to the “drive side” and “idler side” throughout for various instructions. The “drive side”...

  • Page 4: Prior To Installation

    Prior to Installation All screws supporting the awning assembly must have a backer within the structure of the wall of the unit. Refer to the unit's manufacturer for proper location. Resources Required • 2 - 3 People, depending on task •...

  • Page 5: Awning Installation

    Awning Installation On the awning rail, mark the position of the centerlines of the support arm assemblies. Make sure that the support arm assemblies will not interfere with any lights, vents or other obstructions. Using a non-permanent method of marking, mark a perpendicular line from the awning rail down to the floor line.
  • Page 6 Use a screwdriver to spread open either end of the awning rail channel (Fig. 4A). To protect the fabric from damage during installation, file any sharp edges or burrs from the awning rail channel (Fig. 4B). Fig. 4 Use silicone lubricant and spray the inside of the awning rail channel (Fig. 4B). Remove the tape from the fabric.

  • Page 7: Securing The Fabric

    3000 Series motors come stock with an internal 6A auto reset breaker. If this breaker trips, it will take approximately 30 seconds to reset. Lippert recommends the awning be wired into a 15A circuit breaker. All wire shall be 14 AWG or higher as necessary to provide 11.5V minimum at all times to the Lippert-supplied power cable connection.

  • Page 8: Installation With Speakers - Option

    Installation with Speakers — option Fig. 9 Remove wire covers on both mount arms. Radio Wires At both support arm assemblies there will be a wire Speaker Wires labeled "speakers." Connect these to the unit's radio wires (Fig. 9). Note: Speaker wire is indicated with blue insulation on the wiring.

  • Page 9: Seal Wall Penetrations

    Fig. 12 Fig. 13 operation Extending the Awning with The Power Button Switch Note: Some units may not use the Lippert switch (Fig. 13). Verify the unit battery is fully charged and connected to the electrical system. Note: if the unit is equipped with a locking latch, be sure to unlock the latch prior to extending the awning.
  • Page 10 tying down the roll tube once the awning is extended will not allow the free-floating support arms and the wind sensor to work as designed and may cause damage to the awning or Unit. Set pitch using pitch arms with gas strut (Fig.15A). A.

  • Page 11: Retracting The Awning With The Power Button Switch

    Retracting the Awning with The Power Button Switch Note: Some units may not use the Lippert switch (Fig. 13). Verify the unit's battery is fully charged and connected to the electrical system. Note: The awning can be retracted without resetting the pitch.

  • Page 12: Adjusting Pitch Arm Fasteners

    Adjusting Pitch Arm Fasteners If the pitch arm does not hold position, it can be tightened by adjusting the bolt (Fig. 20A) in the center of the pitch arm. Use a 1/2" wrench to tighten the nut (Fig. 20A) while holding the bolt (37B) on the other side of the pitch arm with a 1/4"...

  • Page 13: Wiring Diagram

    Wiring Diagram Fig. 21 Power 15A Circuit Breaker per RVIA Code (oeM Supplied) Ground Manual Black Battery, Rocker Power Source Switch or Converter Blue White Awning Motor *Jumper wire 1 to 6 *Jumper wire Black 4 to 3 White Blue Fig.
  • Page 14 Lippert representative has been provided.  Any unauthorized use shall void any applicable warranty.  The information contained in this manual is subject to change without notice and at the sole discretion of Lippert.  Revised editions are available for free download from lippert.com.

Table of Contents