Icom IC-F4060 Series Service Manual Addendum page 4

November 2012
6-3 TRANSMIT ADJUSTMENT
Select an adjustment item using [↑] / [↓] keys, then set to the specifi ed value using [←] / [→] keys on the connected PC's keyboard.
ADJUSTMENT ADJUSTMENT CONDITION
OUTPUT 1 • Channel
POWER
• Transmitting
[Power (Hi)]
[Power (L2)] 2 • Channel
• Transmitting
[Power (L1)] 3 • Channel
• Transmitting
MODULATION 1 • Channel
BALANCE
• Preset [MOD Narrow]
[BAL (Narrow)]
• No audio applied to the JIG cable.
• Set an FM deviation meter as;
HPF
LPF
De-emphasis
Detector
• Push [P0] key while transmitting.
1 • Frequency
FM
DEVIATION
• Connect an audio generator to the JIG
(NARROW)
cable and set as;
[MOD N C]
Frequency
Level
• Set the FM deviation meter to the same
condition as "MODULATION BALANCE."
• Transmitting
2 • Channel
(NARROW)
[MOD N L] • Transmitting
3 • Channel
(NARROW)
[MOD N H]
• Transmitting
4 • Channel
(WIDE)
[MOD W C] • Transmitting
5 • Channel
(WIDE)
[MOD W L]
• Transmitting
6 • Channel
(WIDE)
[MOD W H] • Transmitting
(MIDDLE) †
7 • Frequency
[MOD M C]
• Transmitting
(MIDDLE) †
8 • Frequency
[MOD M L] • Transmitting
(MIDDLE) †
9 • Frequency
[MOD M H] • Transmitting
1 • Frequency
DIGITAL
DEVIATION*
• Preset [Digital Mode]
[MOD D C]
• Set the FM deviation meter to the same
condition as "MODULATION BALANCE."
• Transmitting
2 • Channel
[MOD D L]
• Transmitting
3 • Channel
[MOD D H]
• Transmitting
1 • Channel
CTCSS/DTCS
DEVIATION • CTCSS
[CTCSS/DTCS]
• No audio applied to the JIG cable.
• Set the FM deviation meter to the same
condition as "MODULATION BALANCE."
• Transmitting
1 • Channel
2/5 TONE
DTMF** • No audio applied to the JIG cable.
[S.Tone]
• Set the FM deviation meter to the same
condition as "MODULATION BALANCE."
• While holding down [P3], Transmit.
†
; [EUR-01] only.
*; Necessary only when the optional UT-119H or UT-126H is installed.
**; For F4160 series.
(Replacement page)
UNIT
: 5 Top
panel
: 6
: 2
: 2 Top
panel
: 80
: OFF
: 20 kHz
: OFF
: (P–P)/2
: 7
Top
panel
: 1.0 kHz
: 150 mV rms
: 8
: 9
: 2
: 1
: 3
: 10
: 11
: 12
: 13
Top
panel
: 7
: 14
: 15
: 16
Top
: 151.4 Hz panel
: 17
Top
panel
6 - 5
MEASUREMENT
OPERATION
Connect an RF power meter to
the antenna connector.
Connect the FM deviation me-
ter to the antenna connector
through an attenuator.
Connect the FM deviation me-
ter to the antenna connector
through an attenuator.
Connect an FM deviation meter to
the antenna connector, through
an attenuator.
Connect an FM deviation meter to
the antenna connector, through
an attenuator.
Connect an FM deviation meter to
the antenna connector, through
an attenuator.
VALUE
5.0 W
2.0 W
1.0 W
As flat as possible.
No over or under shoot.
±2.05 to ±2.15 kHz
±4.05 to ±4.15 kHz
±3.2 to ±3.3 kHz
±1.35 to ±1.39 kHz
±0.68 to ±0.72 kHz
±1.50 kHz