Page 1
Monitor Service Manual Model: VG249Q1A Version no.: 0 Release date: 2024/4/8...
Page 2
ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement. This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.
Page 4
1. Safety Precautions FOR PRODUCTS CONTAINING LASER: DANGER- Invisible laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM. CAUTION- Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION- The use of optical instruments with this product will increase eye hazard. TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF THIS SERVICE MANUAL...
Page 5
2. Exploded View Item Description Q'ty MIDDLE FRAME PANEL #SCREW MACH FLATM3*0.5P*4.5L ZN MAIN BOARD POWER BOARD SPEAKER REAR CASE RUBBER VESA #SCREW FPHM4*10L(7.7/1.6)B-ZNNY #SCREW FH M3*3.5L B-ZN BASE ASSY STAND ASSY KEY BOARD #SCREW TAP-P PH W/FL M3*6L B-ZN SCREW TAP FPH M2.5*4.5L B-NI ASSY SHIELDING #SCREW PH INT/TOO M3*9TP-S C-ZN...
Page 6
3. Disassembly and Assembly Procedures 3.1 Disassembly SOP Preparation before disassemble 1. Clean the room for disassemble 2. Identify the area for monitor 3. Check the position that the monitors be placed and the quantity of the monitor; prepare the area for material flow; according to the actual condition plan the disassemble layout 4.
Page 7
3. Disassemble Rear Case from panel. 4. Take off Key Board FFC from Main Board. 5. Take off Speaker wire from Main Board. 1. Tear off the tapes from the Rear Case. 2. Unlock 3 screws on Rear Case. Screw P/N: 8F.00608.6R0 (#SCRW TAP-P PH W/FL M3*6L B-ZN Y) Screw...
Page 8
1. Remove the tapes. from pane and Shielding 2. Take off light wire from Main Board and panel. 3. Take off conductive tape from Shielding. 4. Pull out the LVDS wire and wire from panel. 5. Disassemble LED BD from Middle frame. 6.
Page 9
11. Disassemble Mylar from Shielding. mylar Main Board 12. Disassemble 7 screw Power on Shielding. Board Main Board Screw P/N: 8F.VC434.9R0 (#SCRW PH INT/TOO M3*9TP-S C-ZN) Power Main Board Board 13. Disassemble Main Board & Power Board from Shielding. 14. Take off the wires from Main Board &...
Page 10
3.2 Assembly SOP Preparation before assemble 1. Clean the room for work 2. Identify the area for material 3. Prepare the implement, equipment and materials as bellow: 1) Working table 2) Screw-driver 3) Glove 4) Cleaning cloth 5) ESD protection After unplugging the power cord, the power Board still have power energe.
Page 11
6. Assemble Lens Board on the Middle frame. 7. Assemble Lamp wire to Panel connector then paste 1 tape. 8. Assemble Middle frame to panel. 9. Lock 9 screws on Middle frame. Screw P/N: 8F.5A224.4R5 (#SCRW MACH FLATM3*0.5P*4.5L ZN) 10. Locate Shielding to panel.
Page 12
1. Assemble Speaker to Rear Case. 2. Stick tapes to Rear Case to fix the wire. 5±0.5Kg/c 3. Assemble the Key Screw driver Board to Rear Case then lock 3pcs screws on Rear Case. Screw P/N: 8F.00608.6R0 (#SCRW TAP-P PH W/FL M3*6L B-ZN Y) 4.
Page 13
5. Assembly stand to Rear Case. 6. Lock 4 screws on Rear Case. Screw P/N: 8F.00729.011 (#SCRW FPHM4*10L(7.7/1.6)B- ZNNY)
Need help?
Do you have a question about the VG249Q1A and is the answer not in the manual?
Questions and answers