Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Phenix Manuals
  4. Inverter
  5. 184600
  6. Instruction manual

Phenix 184600 Instruction Manual

Universal mini inverter
Hide thumbs
1
2
3
4
5

Advertisement

Quick Links

Download this manual
184600
INSTRUCTION MANUAL
UNIVERSAL MINI INVERTER
PURE SINUSOIDAL AC OUTPUT
OUTPUT VOLTAGE AUTO SETTING EQUAL TO INPUT VOLTAGE
AUTO DIMMING (0-10V) OF CONNECTED LOAD UP TO 360W
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. To prevent electric shock, switch off the mains power supply until installation is complete and AC
input power is supplied to this product.
2. This product requires an unswitched AC power supply of 120-277V, 50/60Hz.
3. Make sure all connections are in accordance with the National or Canadian Electrical code and
any local regulations.
4. To reduce the risk of electrical shock, disconnect both normal power, emergency power supplies
and unit connector of this product before servicing.
5. For emergency operation of LED, incandescent, fluorescent fixtures and screw-base lamps.
6. Use this product in 0°C minimum, 50°C maximum ambient temperatures (Ta). It can provide
minimum 90 minutes illumination under the emergency mode.
7. This product is suitable for use in dry or damp locations. Do not use outdoors. Do not mount
it near gas, heaters, air outlets or other hazardous locations.
8. Do not attempt to service the batteries. A sealed, non-maintenance battery is used that is not
field replaceable. Contact the manufacturer for information or service.
9. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition and void warranty.
10. Do not use this product for other than intended use.
11. Installation and service should be performed by qualified service personnel.
12. This product should be mounted in locations and at heights where it will not readily be subjected
to tampering by unauthorized personnel.
THIS PRODUCT CONTAINS A RECHARGEABLE LI-ION BATTERY.
THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
Li-ion
WWW.PHENIXLIGHTING.COM
SAVE THIS INSTRUCTIONS
27E21

Advertisement

loading
Need help?

Need help?

Do you have a question about the 184600 and is the answer not in the manual?

Questions and answers

Related Manuals for Phenix 184600

Summary of Contents for Phenix 184600

  • Page 1 184600 INSTRUCTION MANUAL 27E21 UNIVERSAL MINI INVERTER PURE SINUSOIDAL AC OUTPUT OUTPUT VOLTAGE AUTO SETTING EQUAL TO INPUT VOLTAGE AUTO DIMMING (0-10V) OF CONNECTED LOAD UP TO 360W IMPORTANT SAFEGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1.

  • Page 2: Installation

    With dimmable or non-dimmable load 277V/60Hz 277V/60Hz 2. INSTALLING THE 184600 The 184600 can be mounted inside or outside (nearby or on top of) the luminaire. INSIDE THE LUMINAIRE OUTSIDE THE LUMINAIRE OUTSIDE THE LUMINAIRE One 7/8" (22mm) hole for...
  • Page 3 CAUTION: DO NOT MATE UNIT CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. 1. The 184600 requires an unswitched AC power supply of 120-277 volt, 50/60Hz. 2. Refer to the wiring diagrams below. Make connections in the following order 1 2 3 4 5 6 7 3.

  • Page 4: Operation / Testing / Maintenance

    1. Initial Auto Test When the system is connected properly and powered on, the 184600 will perform an initial Auto Test. If any abnormal conditions exist, the LTS will blink quickly. Once the abnormal condition is corrected, the LTS will function correctly.
  • Page 5 LUMINAIRE LUMINAIRE LUMINAIRE FOR EMERGENCY FOR EMERGENCY * The installer must set the 0-10V dimmer's dimming level to ensure the total output power of 184600 does not exceed 36 Watts in emergency mode. 0-10V BLACK 0-10V DIMMER ② DIM IN GRAY (-) DIMMER ②...