Table of Contents
Advertisement
Quick Links
184600/3
INSTRUCTION MANUAL
EMERGENCY POWER E QUIPMENT
UNIVERSAL MINI INVERTER
PURE SINUSOIDAL AC OUTPUT
OUTPUT VOLTAGE AUTO SETTING EQUAL TO INPUT VOLTAGE
AUTO DIMMING (0-10V) OF CONNECTED LOAD
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. To prevent electric shock, switch off the mains power supply until installation is complete and AC
input power is supplied to this product.
2. This product requires an unswitched AC power supply of 120-277V, 50/60Hz.
3. Make sure all connections are in accordance with the National or Canadian Electrical code and
any local regulations.
4. To reduce the risk of electrical shock, disconnect both normal power, emergency power supplies
and unit connector of this product before servicing.
5. For emergency operation of LED, incandescent, fluorescent fixtures and screw-base lamps.
6. The product is UL Listed for field installation, and use with grounded, Listed, damp location rated
fixtures.
7. Use this product in 0°C minimum, 50°C maximum ambient temperatures (Ta). It can provide
minimum 90 minutes illumination under the emergency mode.
8. This product is suitable for use in dry or damp locations. Do not use outdoors. Do not mount
it near gas, heaters, air outlets or other hazardous locations.
9. Do not attempt to service the batteries. A sealed, non-maintenance battery is used that is not
field replaceable. Contact the manufacturer for information or service.
10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition and void warranty.
11. Do not use this product for other than intended use.
12. Installation and service should be performed by qualified service personnel.
13. This product should be mounted in locations and at heights where it will not readily be subjected
to tampering by unauthorized personnel.
THIS PRODUCT CONTAINS A RECHARGEABLE LI-ION BATTERY.
THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
Li-ion
WWW.PHENIXLIGHTING.COM
SAVE THIS INSTRUCTIONS
21L21
Advertisement
Table of Contents
Related Manuals for Phenix 184600
Summary of Contents for Phenix 184600
- Page 1 184600/3 INSTRUCTION MANUAL 21L21 EMERGENCY POWER E QUIPMENT UNIVERSAL MINI INVERTER PURE SINUSOIDAL AC OUTPUT OUTPUT VOLTAGE AUTO SETTING EQUAL TO INPUT VOLTAGE AUTO DIMMING (0-10V) OF CONNECTED LOAD IMPORTANT SAFEGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1.
- Page 2 With dimmable or 277V/60Hz 277V/60Hz non-dimmable load 2. INSTALLING THE 184600/3 The 184600/3 can be mounted inside or outside (nearby or on top of) the luminaire. INSIDE THE LUMINAIRE OUTSIDE THE LUMINAIRE OUTSIDE THE LUMINAIRE One 7/8" (22mm) hole for...
- Page 3 CAUTION: DO NOT MATE UNIT CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. 1. The 184600/3 requires an unswitched AC power supply of 120-277 volt, 50/60Hz. 2. Refer to the wiring diagrams below. Make connections in the following order 1 2 3 4 5 6 7 3.
- Page 4 20% (Reprogrammed to 30%) of rated luminaire power (max. 180W (PST @ 2 Vdc) or 120W (PST @ 3 Vdc) using Power Share Technology. The 184600 can also be used as a stand alone 36W inverter when used with lighting loads less than or equal to 36 watts.
Need help?
Do you have a question about the 184600 and is the answer not in the manual?
Questions and answers