Subscribe to Our Youtube Channel
Related Manuals for Veigel e LiVe RV1001
Summary of Contents for Veigel e LiVe RV1001
- Page 1 Installation Rehamotive Programming instructions Wheelchair loading e LiVe Item no.: RV1001 www.veigel-automotive.de...
- Page 2 No part of this publication may be reproduced in any form or by any means without the Version 01 prior permission of Veigel GmbH + Co. KG...
-
Page 3: Table Of Contents
Installation Content Content .......................1-3 Revision history ....................1-4 Symbols used ....................1-5 Blank page for notes..................1-6 Programming the wheelchair loading system eLiVe .......... 1-7 Basic programming ...................1-8 Enhanced programming..................1-9 Description of the programming box..............1-10 Preparations for the programming process............1-13 Basic programming..................1-14 Programode: basic, save position 0 ............... -
Page 4: Revision History
Installation Revision history Edition Changes Chapter 01 / 15.11.2023 First edition... -
Page 5: Symbols Used
This sign indicates danger of injury and/or the risk of crushing. Some of the drawings used in these operating instructions may differ from the driving aid you have received! Veigel Hotline Veigel GmbH + Co. KG Telefon: +49 (0) 7941 60585-0 Verrenberger Weg 36 Fax: +49 (0) 7941 60585-20 D-74613 Öhringen... - Page 6 Installation This page is intentionally left blank for notes...
-
Page 7: Programming The Wheelchair Loading System Elive
Installation Programming the wheelchair loading system eLiVe Setup and programming functions: We deliver every eLiVe with a program that includes a preinstalled default loading curve. The default curve is so programmed that the system moves to the maximum end position of the respective actuators. The program is designed so that only the end and intermediate positions need to be changed for individual programming. -
Page 8: Basic Programming
Installation Two different programming levels are available • Basic programming • Enhanced programming Basic programming: In this mode the positions 0 - A - B can be programmed. 0 Comfort setting, here the eLiVe retracts to its smallest overall dimension (smallest overall dimension, e.g. -
Page 9: Enhanced Programming
Installation 2. Enhanced programming: In this mode, positions C - D - E are programmed. If a wheelchair is too large to fit through the door opening or if the door height itself is too low, then additional points must be entered during programming. The positions C- D- E are stop and start points that are additionally inserted into the tilting and lifting phases of the loading curve. -
Page 10: Description Of The Programming Box
Installation Description of the programming box: 1-10... - Page 11 Installation CAN connection cable and power supply: This cable supplies the box with power and connects it to the eLiVe via the CAN interface. 2. On/off switch: Switch on to start the programming process. A short beep will sound after switching on and the orange LED flashing lights on the eLiVe will light up continuously.
- Page 12 Installation 7. Program mode (selector switch): The required program mode can be selected by turning the rotary switch. The selected program mode is then displayed by a control lamp above the switch. basic = 3 point settings enhanced = 6 point settings reset = return to default settings 8.
-
Page 13: Preparations For The Programming Process
Installation Preparations for the programming process: Important: All assembly and adjustment work (except for attaching the securing flanges) on the eLiVe should be completed before programming. Repositioning the tilt arm limit switch requires at least the zero position to be reprogrammed. Caution: Controlling the motors individually by means of the rotary switch or extending or retracting the eLiVe using the pre-installed program poses a... -
Page 14: Basic Programming
Installation Basic programming: In this mode, only the end and intermediate points 0 - A - B will be programmed. 0 Comfort setting, here the eLiVe retracts to its smallest dimension. (smallest dimension, e.g. for installation/removal or for using the seat if the wheelchair loading system hinders its use when the eLive is in the transport position). -
Page 15: Programode: Basic, Save Position 0
Installation Programode: basic, save position 0 End setting 0: Comfort position In this position, the loading system is retracted to its smallest dimension so that the single seat on the right is free and the left door can be closed without collision. •... -
Page 16: Programode: Basic, Save Position A
Installation Programode: basic, save position A End setting A: Loading and unloading position The end and intermediate positions for the extension motor, the tilt motor and the lift plate motor are saved collectively. In this position the wheelchair can be docked on and off. •... -
Page 17: Programode: Basic, Save Position B
Installation Programode: basic, save position B End setting B / transport position: This is the position the wheelchair should be in during transport. The wheelchair is fully loaded into the vehicle so that the left door can close without collision and the wheelchair is not being crushed. -
Page 18: Completing The Basic Programming
Installation Completing the basic programming When the eLiVe is programmed to your satisfaction, switch off the programming box and unplug the cable connecting it to the service connector. Then plug the adapter plug (120 ohm resistor) back into the eLiVe‘s service connection. Programming additional loading curves: In order to program additional loading curves, the loading system must be equipped with the wheelchair recognition system. -
Page 19: Enhanced Programming
Installation Enhanced programming: In this mode, positions C - D - E will be programmed. If the wheelchair is large or the door height is low so that the wheelchair does not fit through, additional points must be added to the programme. The positions C- D- E are stop and start points that are additionally inserted into the tilting and lifting phases of the loading curve. -
Page 20: Programode: Enhanced, Save Position C
Installation Programode: enhanced, save position C Intermediate setting C / Stopping point In this position, the stopping point is saved at which the wheelchair stops with the large wheels in front of the axle. This is necessary in vehicles with little overhead space so that the wheelchair does not get stuck in the door opening when rolling over the axle. -
Page 21: Programode: Enhanced, Save Position D
Installation Programode: enhanced, save position D Intermediate settings D: 2 x stopping points In this position, stopping points for unloading and loading are set. There are two different variants for this; However, the programme automatically recognises during programming which variant you have chosen. - Page 22 Installation Programode: enhanced, save position D Intermediate settings D: Stopping points 1 and 2 Variante 1: (This is necessary if the wheelchair has to be tilted in order to be unloaded). • Tilt arm must be raised (min. 5°) so that the wheelchair can pass under the door. Carriage must be extended so far that the wheelchair can be tilted back into the •...
- Page 23 Installation Programode: enhanced, save position D There are 2 variants in this position. Variante 1: (This is necessary if the wheelchair has to be tilted in order to be unloaded). • Raise the tilt arm (min. 5°) so that the wheelchair can pass under the door. •...
-
Page 24: Programode: Enhanced, Save Position E
Installation Programode: enhanced, save position E Intermediate setting E: path marker point This position saves the starting point from which the tilt arm and lift plate assembly can continue unloading the wheelchair. To do this, the wheelchair must be driven far enough out of the vehicle that it cannot be trapped in the door opening when it is tilted out further. -
Page 25: Completing The Enhanced Programming
Installation Completing the enhanced programming Run and check the saved programme as you unload and load the wheelchair. Make sure that the wheelchair cannot get stuck. If you want to correct a value, go back to enhanced programming and save the position again. -
Page 26: Securing The Wheelchair
Installation Securing the wheelchair Mount the supplied catch hooks on the flanges provided. Now attach the flanges with their attached hooks to the rear mounting brackets on the left and right sides. Adjust the height of the catch hooks to the same height as the holes for the securing cylinders on the side flanges of the lift plate. -
Page 27: Trouble Shooting
Installation Trouble Shooting 1-27... - Page 32 Veigel GmbH + Co. KG Verrenberger Weg 36 D - 74613 Öhringen tel +49 7941 60585 0 fax +49 7941 60585 20 info@veigel-automotive.de www.veigel-automotive.de A SOLUTION FOR EVERY VEHICLE...
Need help?
Do you have a question about the e LiVe RV1001 and is the answer not in the manual?
Questions and answers