Victron Pylontech US2000 Manual
Hide thumbs
Also See for Pylontech US2000:
- Manual (16 pages) ,
- Instructions manual (15 pages) ,
- Manual (13 pages)
Advertisement
Victron & Pylontech UP2500, US2000, US3000, US2000C, US3000C, US5000, US5000B, UF5000, Pelio-L, UP5000,
2024-11-19 14:56 1/11
Victron & Pylontech US2000, US3000 and
Phantom-S
The combination of Victron products with Pylontech lithium batteries has been tested and certified by
the Victron and Pylontech R&D departments.
General information about the battery is found in Pylontech's documentation.
This manual is intended to be used in conjunction with the product manual supplied by Pylontech. It
provides additional and specific information regarding integration with Victron systems.
The Pylontech includes a Battery Management System (BMS) with each battery module. This
interfaces with the Victron
1. Product & system compatibility
Battery US2000 (Plus) US3000 Force-L1
Module capacity
1.1 Offgrid, Backup and Energy Storage Systems are possible
Victron + Pylontech can be used for the following system types:
Off-grid
Grid Backup
Energy Storage Systems - Self Consumption
1.2 A GX-device is required, eg Color Control GX (CCGX) or Venus GX (VGX)
It is essential to use the CAN-bus connection of the
the keep-alive signal, communication of charge and discharge limits, error codes and state of charge.
The minimum required firmware version for the
Victron Energy - https://www.victronenergy.com/live/
GX device
and can support multiple battery modules connected in parallel.
2.4 kWh 3.5 kWh 3.55 kWh
(ESS - Start
page)
GX device
(eg CCGX or VGX) with the batteries for
Color Control GX
is v2.15. It is highly recommended to
Phantom-S, Force-L1 & L2
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Victron Pylontech US2000
Summary of Contents for Victron Pylontech US2000
- Page 1 Phantom-S, Force-L1 & L2 Victron & Pylontech US2000, US3000 and Phantom-S The combination of Victron products with Pylontech lithium batteries has been tested and certified by the Victron and Pylontech R&D departments. General information about the battery is found in Pylontech's documentation.
-
Page 2: Minimum Battery Sizing Recommendations
1.4 All 48V VE.direct BlueSolar and SmartSolar MPPT Chargers are compatible For proper operation, the Pylontech battery needs to be able to control the charge current. Therefor it is recommended to use Victron 48V compatible MPPTs models with VE.Direct port for charging. MPPTs with a VE.Direct port MPPTs are controlled via the device. -
Page 3: Can-Bus Wiring
Victron & Pylontech UP2500, US2000, US3000, US2000C, US3000C, US5000, US5000B, UF5000, Pelio-L, UP5000, 2024-11-19 14:56 3/11 Phantom-S, Force-L1 & L2 Inverter Battery Battery peak Number of continuous continuous peak Inverter / Charger Model watts Pylontech watts @ 25 discharge discharge... -
Page 4: Veconfigure Settings
2019-08-22 11:16 Plug the type B cable with the side which is labeled Battery BMS into the Pylontech CAN port of the master battery. Plug the side labeled Victron VE.Can into the device. Then, plug a VE.Can terminator in the other VE.Can socket on the... - Page 5 Victron & Pylontech UP2500, US2000, US3000, US2000C, US3000C, US5000, US5000B, UF5000, Pelio-L, UP5000, 2024-11-19 14:56 5/11 Phantom-S, Force-L1 & L2 4.3 Inverter Settings In the Inverter tab of VEConfigure VEConfigure Inverter Parameter Setting DC input low shut-down DC input low restart DC input low pre-alarm* * The pre-alarm setting is dependant on your preference and on site specific requirements.
- Page 6 Last update: battery_compatibility:pylontech_phantom https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom?rev=1566465362 2019-08-22 11:16 Hardware Protection Points In normal operation, the charge parameter limits are set by the Pylontech battery and communicated through the system by the GX device to the inverter/charger and MPPT. Low Voltage: When the battery discharges to 44.5V or less, battery protection will turn on. High Voltage: If charging voltage above 54V, battery protection will turn on.
-
Page 7: Ve-Direct Mppt Settings
Victron & Pylontech UP2500, US2000, US3000, US2000C, US3000C, US5000, US5000B, UF5000, Pelio-L, UP5000, 2024-11-19 14:56 7/11 Phantom-S, Force-L1 & L2 This parameters page is also a good place to check that all batteries are connected and working properly. In normal working conditions, the current limit is 25A per cell. For example, 75A charge current limit ( 75 / 25 = 3 ) means there are 3 Pylontech battery modules connected. -
Page 8: Troubleshooting
Last update: battery_compatibility:pylontech_phantom https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom?rev=1566465362 2019-08-22 11:16 8. Troubleshooting If the system is not operating correctly, go through these steps. Step 0. If the Inverter/Charger or GX device does not switch on As a safety precaution, the inverter/charger will not switch on if the GX device is not on. - Page 9 If its not visible, check: GX device firmware version (update to latest version, v2.15 or later) CAN-bus communication cabling between Pylontech and Victron system. Make sure that it is in the right way around. Pylontech system is up and running (LEDs are on) Step 2.
- Page 10 Pylontech's BMS will restrict the Charge Current Limit of the battery in cold weather. The precise temperatures and limits are not published by Pylontech, but anecdotally from reports on Victron Community it would appear that batteries begin to be limited below 18 degree C, severely limited below 10 degrees C, and completely restricted from charging below 2 degrees C.
-
Page 11: Further Information
Victron & Pylontech UP2500, US2000, US3000, US2000C, US3000C, US5000, US5000B, UF5000, Pelio-L, UP5000, 2024-11-19 14:56 11/11 Phantom-S, Force-L1 & L2 10. Further Information For information about where to buy or find suitably qualified installers, visit the Where to Buy Page.
Need help?
Do you have a question about the Pylontech US2000 and is the answer not in the manual?
Questions and answers