Advertisement

Quick Links

2019-02-19 08:06
Victron & Pylontech US2000B and Phantom-S
The combination of Victron products with Pylontech lithium batteries has been tested and certified by
the Victron and Pylontech R&D departments.
General information about the battery is found in Pylontech's documentation.
This manual is intended to be used in conjunction with the product manual supplied by Pylontech. It
provides additional and specific information regarding integration with Victron systems.
The Pylontech includes a Battery Management System (BMS) with each battery module. This
interfaces with the Victron
parallel.
1. Product & system compatibility
Battery US2000B US2000B Plus US3000 Plus
Module capacity
2.4 kWh
1.1 Offgrid, Backup and Energy Storage Systems are possible
Victron + Pylontech can be used for the following system types:
Off-grid
Grid Backup
Energy Storage Systems - Self Consumption
1.2 A Venus-device is required, eg Color Control GX (CCGX) or Venus GX (VGX)
It is essential to use the CAN-bus connection of the
for the keep-alive signal, communication of charge and discharge limits, error codes and state of
charge.
The minimum required firmware version for the
use the latest firmware version on all connected devices, including CCGX/VGX, Inverter/Charger and
Victron Energy - https://www.victronenergy.com/live/
1/10
Venus-device
and can support multiple battery modules connected in
2.4 kWh
3.5 kWh
(ESS - Start
page)
Venus-device
(eg CCGX or VGX) with the batteries
Color Control GX
is v2.15. It is highly recommended to
Victron & Pylontech US2000B and Phantom-S

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Pylontech US2000B and is the answer not in the manual?

Questions and answers

Summary of Contents for Victron Pylontech US2000B

  • Page 1 Victron & Pylontech US2000B and Phantom-S Victron & Pylontech US2000B and Phantom-S The combination of Victron products with Pylontech lithium batteries has been tested and certified by the Victron and Pylontech R&D departments. General information about the battery is found in Pylontech's documentation.
  • Page 2: Minimum Battery Sizing Recommendations

    1.4 All 48V VE.direct BlueSolar and SmartSolar MPPT Chargers are compatible For proper operation, the Pylontech battery needs to be able to control the charge current. Therefor it is recommended to use Victron 48V compatible MPPTs models with VE.Direct port for charging. MPPTs with a VE.Direct port MPPTs are controlled via the Venus-device.
  • Page 3: Can-Bus Wiring

    The battery with the empty link port 0 is the master battery. Using the VE.Can to CAN-bus BMS type B Cable, part number ASS030720018, Plug the side which is labeled Battery BMS into the Pylontech CAN port of the master battery. Plug the side labeled Victron VE.Can into the Venus-device. Victron Energy - https://www.victronenergy.com/live/...
  • Page 4: Veconfigure Settings

    Last update: battery_compatibility:pylontech_phantom https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom 2019-02-18 22:06 Then, plug a VE.Can terminator in the other VE.Can socket on the Venus-device. Two VE.Can terminators are included with the package of the Venus-device as an accessory, only one is used. Keep the other one as a spare. More information about the cable can be found in manual.
  • Page 5 2019-02-19 08:06 5/10 Victron & Pylontech US2000B and Phantom-S VEConfigure Inverter Parameter Setting DC input low shut-down DC input low restart DC input low pre-alarm* 48.5V * The pre-alarm setting is dependant on your preference and on site specific requirements. You may wish for this to be activated earlier in an off...
  • Page 6: Venus-Device Settings

    Last update: battery_compatibility:pylontech_phantom https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom 2019-02-18 22:06 High Voltage: If charging voltage above 54V, battery protection will turn on. Working discharge temperature range is from -10 to 50 degrees celsius. Charging temperature range is from 0 to 50 degrees celsius. Discharge Current Limit set to 0A at 47V, inverter will turn off. Over-charge and Over-discharge Current Limit 102A for 15 seconds, 200A for 0.1 seconds and 400A short circuit current.
  • Page 7: Ve-Direct Mppt Settings

    2019-02-19 08:06 7/10 Victron & Pylontech US2000B and Phantom-S This parameters page is also a good place to check that all batteries are connected and working properly. In normal working conditions, the current limit is 25A per cell. For example, 75A charge current limit ( 75 / 25 = 3 ) means there are 3 Pylontech battery modules connected.
  • Page 8: Troubleshooting

    Last update: battery_compatibility:pylontech_phantom https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom 2019-02-18 22:06 8. Troubleshooting If the system is not operating correctly, go through these steps. Step 0. If the Inverter/Charger or Venus-device does not switch on As a safety precaution, the inverter/charger will not switch on if the Venus-device is not on.
  • Page 9 If its not visible, check: Venus-device firmware version (update to latest version, v2.15 or later) CAN-bus communication cabling between Pylontech and Victron system. Make sure that it is in the right way around. Pylontech system is up and running (LEDs are on) Step 2.
  • Page 10: Further Information

    10. Further Information For information about where to buy or find suitably qualified installers, visit the Where to Buy Page. Further community discussion about installing and using Pylontech and Victron can found at Victron Community, use the topic label 'Pylontech'.

This manual is also suitable for:

Pylontech phantom-s

Table of Contents