Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Naicon ELSIST FLEXIBLE 6000
Summary of Contents for Naicon ELSIST FLEXIBLE 6000
- Page 1 Rack-Tower Conversion Single Phase UPS Electrical System for Continuity...
-
Page 2: Table Of Contents
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE Contents 1．Safety ..........................3 1.1 Safety notes ..........................3 1.2 Symbols used in this guide ......................3 2．Main Features ........................ 3 2.1 Summarization ..........................3 2.2 Functions and Features ........................ 3 3．Installation ........................4 3.1 Unpack checking ........................... -
Page 3: 1．Safety
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE 1. Safety Important safety instructions – Save these instructions There exists dangerous voltage and high temperature inside the UPS. During the installation, operation and maintenance, please abide the local safety instructions and relative laws, otherwise it will result in personnel injury or equipment damage. -
Page 4: 3．Installation
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE -stage: Constant Voltage In order to vitalize battery and make sure batteries are fully charged stage: Floating mode. With this 3-stage charging method, it extends the life of the batteries and guarantees fast charging. LCD Display ◆... -
Page 5: Lcd Control Panel
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE Side View 3.3 LCD control panel LCD control panel introduction (1) INVERTER LED (2) BATTERY LED (3) BYPASS LED (4) ALARM LED (5) LCD display (6) UP button (7) DOWN button (8) ESC /OFF button (9) ENTER/ON button 3.4 Installation notes ◆Please place the UPS in a clean, stable environment, avoid the vibration, dust, humidity, flammable gas and liquid, corrosive objects. -
Page 6: External Protective Devices
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE ◆Batteries should be mounted in an environment where the temperature is within the required specs. Temperature is a major factor in determining battery life and capacity. In a normal installation, the battery temperature is maintained between 15°C and 25°C. Keep batteries away from heat sources or main air ventilation area, etc. -
Page 7: Power Cables
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE 3.6 Power Cables ◆ The cable design shall comply with the voltages and currents provided in this section, Kindly follow local wiring practices and take into consideration the environmental conditions (temperature and physical support media) . -
Page 8: Battery Connection
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE WARNING If the load equipment is not ready to accept power on the arrival of the commissioning engineer then ensure that the system output cables are safely isolated at their ends CAUTION The earthing and neutral bonding arrangement must be in accordance with local and national codes of practice. -
Page 9: Ups Multi－Module Installation
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE 3.9 UPS Multi - Module Installation The basic installation procedure of a parallel system comprising of two or more UPS modules is the same as that of single module system. The following sections introduce the installation procedures specified to the parallel system. -
Page 10: Requirement For The Parallel System
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE 3.9.3 Requirement for the parallel system A group of paralleled modules behave as one large UPS system but with the advantage of presenting higher reliability. In order to assure that all modules are equally utilized and comply with relevant wiring rules, please follow the requirements below: 1) All UPS must be of the same rating and be connected to the same bypass source. -
Page 11: 4．Operation
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE 4. Operation 4.1 Operation Modes The UPS is a double-conversion on-line UPS that may operate in the following alternative modes: ◆ Normal mode The rectifier/charger derives power from the AC Mains and supplies DC power to the inverter while floating and boosting charge the battery simultaneously. -
Page 12: Black(Cold) Start Procedure
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE 4.2.2 Black (Cold) start procedure CAUTION Follow these procedures when the input AC Utility Failure, but battery is normal. ◆ Turn on the battery switch. The battery will feed the Auxiliary power board. ◆... -
Page 13: Lcd Display Instruction
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE 4.3 LCD Display instruction NOTICE! The display provides more functions than those described in this manual. Below the available interfaces in the LCD display: ITEM INTERFACE DESCRIPTION CONTENT DISPLAYED Input Voltage & Frequency Output Voltage &... -
Page 14: Parameters Setting
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE Press “DOWN” button, the UPS goes to next page as shown below. (2) Input voltage (3) Output voltage (4) Bat + voltage (Positive) (5) Bat – voltage (Negative) (6) Load (7) PFC/ Ambient temperature up, only shows the high temperature Internal temperature (down) (8) Bus voltage... -
Page 15: Mode Setting
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE 4.4.1 Mode setting Mode setting (Note: Inside the broken-line is the flashing part) After ENTERing the setting menu, it’s mode setting defaulted, and the mode setting line flashing as in above picture. • Use button ENTER /ON to choose different mode. -
Page 16: Battery Capacity Setting
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE To change the Output frequency before you need to change the Mode setting (4.4.1) following this instruction: UPS must stay in By-pass mode (press OFF key for 1-2 sec to Turn OFF the inverter) 1) Press together UP and DOWN for 2 sec to open the Menu 2) Scroll the Menu with UP or DOWN keys to select 01 (MOD) and press ENTER. -
Page 17: Bypass Volt-Hi Setting
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE • Press ESC/OFF button to exit the battery quantity setting (save the battery quantity setting) and goes to battery capacity setting or bypass voltage upper limit setting. 4.4.6 Bypass Volt-Hi setting Bypass voltage upper limit setting (Note: Inside the broken-line is the flashing part) When under the battery quantity setting press DOWN or when under bypass voltage lower setting press UP, it goes to the bypass upper limit setting. -
Page 18: Battery Test Setting
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE Press DOWN under bypass voltage lower limit setting or press UP under the parallel ID setting can ENTER the buzzer setting. Now the setting status is flashing as the Figure shows (note: on=mute; off= no mute). When press, it shows the mute cycle setting, the selection includes ON and OFF. -
Page 19: Parallel Id Setting
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE 4.4.10 Parallel ID setting Parallel ID setting (Note: Inside the broken-line is the flashing part) When under the bypass voltage lower limit setting press DOWN or when under parallel quantity setting press UP, it goes to the parallel ID setting. -
Page 20: Appendix 1 Specifications
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE Appendix 1 Specifications MODEL FLEXIBLE 6000 FLEXIBLE 10000 Phase Single phase with ground Capacity (VA/Watts) 6000VA / 5400W 10000VA / 9000W INPUT Nominal Voltage 208/220/230/240VAC 187Vac±5% @ 100%-80%load 160Vac±5% @ 80%-70%load 140Vac±5% @ 70%-60%load Low line transfer Operating 120Vac±5% @ 60%-50%load... -
Page 21: Battery Pack
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE EPO (optional) Shut down UPS immediately Audible & Visual alarms Line Failure, Battery Low, Overload, System Fault Comunication interface USB / RS232, SNMPcard (optional), Relay card (optional) ENVIRONMENTAL Operating temperature 0°C~40°C Storage temperature -25°C~55°C Humidity range 20-90 % RH @ 0- 40°C (non-condensing) -
Page 22: Appendix 4 Ups Message Table
FLEXIBLE 6K●10K SINGLE PHASE – SINGLE PHASE Appendix 4 UPS message table This section lists the alarm messages that the UPS might display. This section is listed with each alarm message to help you troubleshoot problems. 4.1 Alarm Information ITEM UPS ALARM WARNING BUZZ Rectifier Fault... - Page 24 Naicon srl Via il Caravaggio, 25 Trecella I-20060 Pozzuolo Martesana - Milano (Italy) Tel. +39 02 95.003.1 Fax +39 02 95.003.313 www.naicon.com e-mail: naicon@naicon.com...
Need help?
Do you have a question about the ELSIST FLEXIBLE 6000 and is the answer not in the manual?
Questions and answers