Do you have a question about the GT73 and is the answer not in the manual?
Questions and answers
Brandon Brock
April 26, 2025
How do I program a new replacement nfc card to my GT 73
3 comments:
Mr. Anderson
May 13, 2025
To program a new replacement NFC card to the Riding'Times GT73, place the NFC card on the white Riding'Times box below the screen. If it does not work automatically, you may need to manually pair the NFC card with the screen.
This answer is automatically generated
Shawn G
July 11, 2025
@Brandon Brock My two nfc cards were inadvertently dropped in the trash, how do you obtain replacement NFC cards?
Shawn G
July 11, 2025
@Brandon Brock Also I need to replace my battery keys as well do you get them at the same place as the new NFC cards?
John Kovarik
March 29, 2025
hello .....and......just got my GT73 and there is a BEEP that comes from the Display and a Green Arrow points to the Battery. It has two Red Bars showing on the level .....the rest is Green. So, I think It is fully charged.
2 comments:
Mr. Anderson
March 29, 2025
On the Riding'Times GT73, when it shows two red bars, a beep and a green arrow pointing to the battery indicate that the secondary NFC card has been successfully added.
This answer is automatically generated
John Kovarik
March 29, 2025
@Mr. Anderson It is beeping ALL THE TIME . How do I get it to STOP BEEPING ?
Bronson Grace
May 9, 2025
What to do about Error code (E07) Motor Hall Failure?
What do I do to fix this problem?
1 comments:
Mr. Anderson
May 19, 2025
To fix Error Code E07 (Motor Hall Failure) on the Riding'Times GT73:
1. Locate the Hall sensor cable near the motor. 2. Disconnect the Hall sensor cable. 3. Carefully reinsert the cable, making sure it is properly aligned and fully seated. 4. Restart the bike and check if the error code is cleared.
If the issue persists, record a video and contact support. The motor may need replacement under warranty.
This answer is automatically generated
Nieko
April 15, 2025
How to charge battery
1 comments:
Mr. Anderson
April 15, 2025
To charge the battery for the Riding'Times GT73:
1. Switch off all batteries before charging. 2. Choose a charging method: - Option A: Remove the batteries from the bike and connect them individually to the charger. - Option B: Charge the batteries while still attached to the bike by plugging the charger in directly. 3. Plug the charger into a standard power outlet and connect it to the battery charging port. 4. Monitor the charger LED: - Red: Charging - Green: Fully charged 5. After charging, replace the protective caps on the battery ports to prevent dirt and moisture entry.
This answer is automatically generated
Viktor
July 18, 2025
After i restored my bike to the factory settings i can't add NFC card, menu PO7 doesn't react on it. On start menu appeared number 1 it looks like NFC, P and 1 . Tell me please what i should do to fix it
Ian
June 16, 2025
The gt73 is beeping for no particular reason
cash
May 26, 2025
what seat cover can i use for the gt73 e bike
Rasmus Teglgaard-Thers
May 18, 2025
Hi. I have a question concerning the 2000W engine.
We are going to move to United Kingdom and they have a Watt limit on bikes at 250W - Will that be a concern?
What would it cost to get it delivered in UK, Plymouth?
Zachary Coleman
May 17, 2025
I just need to know the battery continuous Amp Discharge or MAX line current
I also need to know the GT73 motor poles
Wgrimes
May 15, 2025
I would like to remove the p position from the controller this has caused the bike to stall at crosswalks and lights and requires multiple brake and power button presses to release
Page 1
Original Instructions User's Manual GT73 electric bike...
Page 2
Welcome 1. Join the Riding'times community of riders wherever you are! This is just the beginning of your adventure with us! We look forward to hearing about your experience and seeing you online on our social networks: Facebook Group Name: Riding'times Global Group Group Link: https://www.facebook.com/groups/1331441984237849...
Page 3
5.Customer Service EN:Our product technology is already very mature, with 20 years of trade, we have distributors all over the world who can provide you with the most localized and professional technical support within 24 hours. DE:Unsere Produkttechnologie ist sehr ausgereift, mit 20 Jahren Handel haben wir weltweit Vertreter, die Ihnen innerhalb von 24 Stunden die bestmögliche lokalisierte und professionelle technische Unterstützung bieten.
Page 4
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TY technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. European Union Compliance Statement Battery recycling information for the European Union Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning batteries and accumulators and waste batteries and accumulators.
Page 5
• Because electric bikes are significantly heavier than regular bikes, they are not intended for large jumps or stunts of any kind. Bike frames and parts have limitations, and extreme riding should not be performed. GT73 assumes no liability for any accident, injuries,or property damage incurred as a result of rider’s use or misuse of GT73 bicycles, including any damages resulting from or arising out of off-road usage.
Page 6
at the same time, as it may generate a large short-circuit current and lead to an accident.Any aftermarket changes or modifications to your bike could void the warranty and create an unsafe riding experience. • Ride at night only if necessary. Wear reflective clothing; if possible, only bike down roads with ample street lighting.
2.Assemble Electric Bike 2.1.Take out of the electric bike from the box 2.2.Assemble the handlebar: Put the handlebar into the center of the vertical bar (Figure 1), fasten the screws by using NO.4 Allen Wrench Figure 2...
Page 11
2.8.Assemble the pedal plate: Take out of the left and right pedal plate, “L “is for left side and “R” is for the right side (Figure 1) , put the pedal plate on the crank, fasten it by using the open spanner (Figure 2) . Figure 2 Figure 1 2.9 Install the left and right cranks into the central axis of the frame.
Page 12
2.10 Schematic diagram of display circuit docking (Note: the corresponding limit of each waterproof head cannot be installed incorrectly to avoid hardware damage).
Page 13
2.11Manage the cable harness: Take out of the winding tube from the accessory box, tie the left and right wire harnesses together.
3.Product Parameters/Features 3.1Product Parameters GT73 electric bike sheet Model GT73 Product name electric bike Configuration NFC card none battery model 48V 18.2AH*2 Battery weight About5.16 KG Motor Motor*1 charger 54.6V/2A*2 Charging time Single charger 9-10H display Digital display instrument LED...
Page 15
3.2.Product Features 3.2.1. Speed mode: 3.2.2.Pure assist mode: factory default 25KM/H. 3.2.3. Throttle and assist coexistence mode: ECO gear 25KM/H, STD gear 35KM/H, TURBO gear 60KM/H. 3.2.4. Braking method: power-off braking. 3.2.5. Tail light: The light is always on when turned on, and highlighted when the brake is applied. 3.2.6.
4.Battery Instructions 4.1Battery charging This bicycle is an external lithium battery, which can be removed for charging. When the battery is low, open the key and take out the battery. Hold the battery tightly with both hands to prevent it from falling, Take out the charger, plug the input end into the power supply,Insert the M16 aviation head of the output terminal into the battery charging hole.
5.Instructions of Dashboard 1.1. Specifications 48V power supply Rated working current 15mA Maximum working current 30mA Leakage current at power-off<1uA Working current at the supply controller end 50mA Working temperature- 2 0 ~ 6 0 ℃ Storage temperature-3 0 ~ 7 0 ℃ 5.2.
Page 18
5.4.Display/Press Function overview and functional area layout 5.4.1Display Function overview and functional area layout 1.NFC 2.Headlight 3.Cruise control 4.Power 5.Single mileage 6.Speed 7.Range 8.Max speed 9.Energy saving mode 10.Nomal 11.Sport mode 12.Push mode 5.4.2Button Function overview and functional area layout 13.Headlight switch 14.Function 15.Tum on/off...
Page 19
5.5.General operation 1. Turn on and off: Press and hold the power button for 2 seconds to turn on/off (Figure 5-1), put the NFC card on the interface (Figure 5-1), unlock it after hearing the beeping sound, and after unlocking, the display (Figure 5-2) will enter the normal mode.
Page 20
4.2. Function menu switching: In the setting interface state, Press to increase the menu options upward; Press to decrease the menu options downward; 4.3. Function menu parameter switching: In the function menu interface state, Press the "S" key to increase the parameters upward;...
Page 21
P04: Brightness adjustment. 1 darkest; 2 normal; 3 brightest; default 3 (Figure 5-10) 5-10 P05: Sleep time setting: 1-60 minutes; default 10 minutes (Figure 5-11) 5-11 P06: Clear total mileage: Long press the "S" key (Figure 5-12) 5-11 P07: Add 2 NFC secondary cards (Figure 5-12), put the card on the display, hear a beep, 0 changes to 1, indicating the addition is successful (Figure 5-13).
6.Considerations Please use it safely, and do not plug or unplug the display when it is powered on. · Please avoid bumping as far as possible. · Please do not alter the background parameter settings of the display at will otherwise normal riding cannot be guaranteed ·...
8.Oil brake maintenance 8.1. Please read the manual before maintenance and do not leave it to inexperienced personnel. 8.2. The upper and lower pumps of this product produce braking function by extrusion through the oil pipe output. The internal oil should be maintained after 10 months under normal use (except for other improper use) to avoid air generated inside the brake pump causing braking.
Page 24
7. Insert the short hose into the oil filling barrel, connect the hose and the oil cylinder with the M4 oil filling nozzle connector, and then tighten the screws by hand. 8. Use another oil filling cylinder to extract 20ml of new engine oil 9.
Page 25
12. During the last pump, a little oil is left in the oil filling barrel. 13. Replace the oil filling cylinder with the exhaust gas cylinder. When pulling out the oil filling barrel, wrap it with a cloth to prevent oil from overflowing. 14.
Page 26
18. Bleed the air from this end of the handbrake lever and extract the air from the tube 19. Repeat extraction several times until no bubbles or very few bubbles are visible in the tube. 20. After the last injection, loosen the interface and tighten the oil seal screw. 21.
9.Troubleshooting Instructions Display error code Fault name Fault name Fault code Fault code Brake failure Throttle Handle failure Lack voltage protection Controller failure Controller/Display communication Motor Hall failure failure 10.Warranty (1). Warranty information For the faults caused by the quality of the product under normal use, the company will be ·...
Need help?
Do you have a question about the GT73 and is the answer not in the manual?
Questions and answers
How do I program a new replacement nfc card to my GT 73
To program a new replacement NFC card to the Riding'Times GT73, place the NFC card on the white Riding'Times box below the screen. If it does not work automatically, you may need to manually pair the NFC card with the screen.
This answer is automatically generated
@Brandon Brock My two nfc cards were inadvertently dropped in the trash, how do you obtain replacement NFC cards?
@Brandon Brock Also I need to replace my battery keys as well do you get them at the same place as the new NFC cards?
hello .....and......just got my GT73 and there is a BEEP that comes from the Display and a Green Arrow points to the Battery. It has two Red Bars showing on the level .....the rest is Green. So, I think It is fully charged.
On the Riding'Times GT73, when it shows two red bars, a beep and a green arrow pointing to the battery indicate that the secondary NFC card has been successfully added.
This answer is automatically generated
@Mr. Anderson It is beeping ALL THE TIME . How do I get it to STOP BEEPING ?
What to do about Error code (E07) Motor Hall Failure? What do I do to fix this problem?
To fix Error Code E07 (Motor Hall Failure) on the Riding'Times GT73:
1. Locate the Hall sensor cable near the motor.
2. Disconnect the Hall sensor cable.
3. Carefully reinsert the cable, making sure it is properly aligned and fully seated.
4. Restart the bike and check if the error code is cleared.
If the issue persists, record a video and contact support. The motor may need replacement under warranty.
This answer is automatically generated
How to charge battery
To charge the battery for the Riding'Times GT73:
1. Switch off all batteries before charging.
2. Choose a charging method:
- Option A: Remove the batteries from the bike and connect them individually to the charger.
- Option B: Charge the batteries while still attached to the bike by plugging the charger in directly.
3. Plug the charger into a standard power outlet and connect it to the battery charging port.
4. Monitor the charger LED:
- Red: Charging
- Green: Fully charged
5. After charging, replace the protective caps on the battery ports to prevent dirt and moisture entry.
This answer is automatically generated
After i restored my bike to the factory settings i can't add NFC card, menu PO7 doesn't react on it. On start menu appeared number 1 it looks like NFC, P and 1 . Tell me please what i should do to fix it
The gt73 is beeping for no particular reason
what seat cover can i use for the gt73 e bike
Hi. I have a question concerning the 2000W engine. We are going to move to United Kingdom and they have a Watt limit on bikes at 250W - Will that be a concern? What would it cost to get it delivered in UK, Plymouth?
I just need to know the battery continuous Amp Discharge or MAX line current I also need to know the GT73 motor poles
I would like to remove the p position from the controller this has caused the bike to stall at crosswalks and lights and requires multiple brake and power button presses to release