Advertisement
JGS524E_IG_11Oct10.fm Page 2 Tuesday, October 12, 2010 11:44 AM
Specifications
Technical Specifications
Standards
IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u 100BASE-TX
compatibility
Fast Ethernet, IEEE 802.3x Flow Control, IEEE 802.1p and
TOS priority, WRR queuing with four queues
Network interface
RJ-45 connector for 10BASE-T, 100BASE-TX, or 1000BASE-T
Power Consumption
13.5W max
AC Power
100-240VAC 50-60Hz,0.9A max.
Weight
1.73 Kg (3.79 lbs)
Dimensions
330 mm x 173 mm x 43 mm
(W x D x H)
13 in x 6.8 in x 1.7 in
Operating
0 to 40° C (32 to 104° F)
temperature
Operating humidity
10% t0 90% relative humidity, non-condensing
Electromagnetic
CE Class A, included EN55022 (CISPR 22) and EN55024,
compliance
FCC part 15 Class A, VCCI Class A, C-Tick Class A, CCC
Power adapter safety
CE mark, Commercial UL listed (UL 60950-1), C-Tick, CCC,
agency approvals
CB
Performance Specifications
Frame filter rate
14800 frames/sec max for 10M port; 148,800 frames/sec max
for 100M; 1,488,000 frames/sec max for 1000M port
Frame forward rate
14,800 frames/sec max for 10M port; 148,800 frames/sec max
for 100M port; 1,488,000 frames/sec max for 1000M port
Performance Specifications (continued)
Network latency
1000 Mbps to 1000 Mbps: 6.0 μs max.
(using 64-byte
packets)
Address database
up to 8K MAC addresses
size
MAC Address
Automatically updated
Learning
Queue buffer
512 KB
NETGEAR Green
• Auto power-down mode saves energy when ports are unused
features
• Power-saving per port if the cable length is less than 32.8 feet
(10 meters)
Troubleshooting Tips
Problem
Action
Power light is not lit
The switch has no power. Make sure that:
• The power cord is properly connected to the switch.
• The power cord is properly connected to a functioning power
outlet. If it is in a power strip, make sure the power strip is turned
on. If the socket is controlled by a light switch, make sure the
switch is in the on position.
Port number light is
There is a hardware connection problem.
not lit for a connected
• Make sure the cable connectors are securely plugged in at the
device, or stays on
switch and the device.
continuously
• Make sure the connected device is turned on.
• If the Ethernet cable is connected to a NIC or other Ethernet
adapter, make sure the card or adapter is installed correctly and
is working.
• Make sure the cable is less than 328 feet (100 meters).
October 2010
Technical Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and
use it to register your product at
http://www.NETGEAR.com/register
required before you can use the telephone support service. Registration via our
website is strongly recommended.
Go to
http://kbserver.netgear.com
for product updates and Web support
For additional information about setting up, configuring, and using your 5-port
Enhanced Switch, see the User Manual
.
For complete DoC please visit the NETGEAR EU Declarations of Conformity
website at:
http://kb.netgear.com/app/answers/detail/a_id/11621/
© 2010 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks of
NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or
registered trademarks of their respective holders. Information is subject to change without notice.
. Registration is
.
Advertisement
