MARANTZ DESIGN AND SERVICE Using superior design and selected high grade components, company has created the ultimate in stereo sound. MARANTZ Only original MARANTZ parts can insure that your MARANTZ which it is famous. Parts for your equipment are generally available to our National Subsidiary or Agent.
1. TECHNICAL SPECIFICATIONS Power output (20 Hz – 20 kHz simultaneous drive of both Maximum allowed PHONO input (1kHz) channels) ..........MC ................. 15 mV ............MM ..............150 mV Headphone rated output (When speaker rated output set RIAA deviation (20Hz ~ 20kHz) ......±0.5 dB ........
Page 4
2. "+" of Connect Digital Voltage is connected to the No.1 ピンを"+"、 3 番ピンを"-" に接続します。 pin and connected "-" to No.3 pin of J609 (J709). 3. PM-15S2のフ ァンクシ ョ ンはCDにして、 ボ リ ュームは-∞に、 入力端子には何も接続しないでく ださい。 anything with the input terminal.
Page 5
Digital Voltmeter Digital Voltmeter PHONO F.C.B.S. PRE OUT SPEAKER SYSTEMS P.DIRECT BI.AMP PHONO STEREO SPEAKER IMPEDANCE : 4 - 8 OHMS R CH L CH LINE 2 RECORDER 2 DC オフセット電圧調整 DC Offset Voltage Adjustment 5. First, adjust the DC offset voltage with the variable resistor 5.
4. SERVICE MODE DISPLAY button DISPLAY ATT button POWER ON/OFF button 1. To enter the Service Mode, press the POWER ON/OFF 1. 本 体 の DISPLAY ボ タンと ATT ボ タン を 押し な が ら button with pressing the DISPLAY and ATT buttons to POWER ON/OFFボタンを押します。...
2. Press DISPLAY button, the display will be the following. 2. DISPLAYボタンを押します。下記の表示になり ます。 3. Press DISPLAY button, the display will be the following. 3. DISPLAYボタンを押します。下記の表示になり ます。 4. Turn off power to quit service mode. 4. POWER ON/OFFボタンを押し、 電源を切り ます。サービ Service mode can be ended if turn off power from every スモー...
5. PROTECTION 動作について 5. PROTECTION MODE Explanation of microprocessor (QU01) [PROT-1 (pin54) and マイコン(QU01)のPROT-1 (pin54) とPROT-2 (pin53)の説明。 PROT-2 (pin53)]. [A] PROT-1(pin54) は、 パワーアンプの下記の異常動作を検 [A] The PROT-1(pin54) is the port to detect the 出するポー ト following abnormalities of the Power AMP 1.
Page 9
To check if the amp is in order, switch off the unit and switch [B] PROT-2 (pin53) は、 電源回路の異常を検出するポー ト it on again one minute later. This action will deactivate 1. パワーアンプ用電源回路の異常を検出。 the protection operation. If the PROT-1 (pin54) remains パワーアンプ用電源の...
6. MAIN MICROPROCESSOR (QU01) 6. MAIN MICROPROCESSOR (QU01) UPDATE アップデート方法 PROCEDURE Necessary Equipment 必要機器 Windows PC (OS:Windows2000 または WindowsXP) COM port でCOM port のあるもの RS232Cス ト レー トケーブル (9pinメ ス- 9pinメ ス) female) マイコンア ッ プデー トディ スク (90M-PM15S2CDR) マイコンア ッ プデー トキッ ト ( 部品番号...
Page 11
The explanation drawing 説明図について The explanation drawings are using PM-11S1 in this 説明図は PM-11S1 を使用しています。 図中に PM-11S1 section. Please replace with PM-15S2 the portion と記載されている箇所は PM-15S2と置き換えて操作して currently mentioned as PM-11S1, and operate it. く ださい。 1. Open the CD-ROM (90M-PM15S2CDR) Disc, and double 1.
Page 16
6.3. 書き込みソフトウェアの設定 6.3. The writing software setup procedure. Launch up the writing software. ソフ ト ウ ェ アの起動 1. Click Start / Programs / Renesas / Flash Development 1. Start / Programs / Renesas / Flash Development Toolkit 3.0 / Flash Development Toolkit 3.0. Toolkit 3.0 / Flash Development Toolkit 3.0 をク...
Page 17
3. Check Create a new project workspace, and click OK. 3. Create a new project workspace にチェ ッ クを入れ、 OK をク リ ッ ク します。 4. PM-15 is inputted into the Workspace name. 4. Workspace Name に PM-15と入力します。 (It is simultaneously inputted into Project Name.) ( 同時に...
Page 18
6. Choose the Serial port No. in the Select Port. 6. Select Portから接続するSerial Port 番号を選び、 ク リ ッ ク Click Next. します。Nextをク リ ッ ク します。 7. 8.0 is inputted into the "Enter the CPU crystal frequency 7. "Enter the CPU crystal frequency for the selected for the selected device:".
Page 19
9. Check the Automatic in Protection. 9. ProtectionからAutomaticにチェ ッ クを入れます。 Check the Advanced in Messaging. MessagingからAdvancedにチェ ッ クを入れます。 Click Finish. Finishをク リ ッ ク します。 以上で設定は完了です。...
Page 20
6.4. 書き込み方法 6.4. Writing procedure 1. Click Start / Programs / Renesas / Flash Development 1. Start / Programs / Renesas / Flash Development Toolkit3.0 / Flash Development Toolkit3.0. Toolkit3.0 / Flash Development Toolkit3.0 をク リ ッ ク します。 2. Click OK. (This window appears at every starting) 2.
Page 21
5. Open the CD-ROM (90M-PM15S2CDR) and double click 5. ア ッ プデー トディ スク (90M-PM15S2CDR) の softフ ォルダ soft folder. をダブルク リ ッ ク します。 6. Select V090507.mot, and Click Add. 6. V090507.motを選択し、 Addをク リ ッ ク します。 7. The holder of V090507.mot is made. 7.
Page 22
8. It checks that PM-15S2 and the COM port are connected 8. PM-15S2とWindows PC の COM ポー トの接続を確認し by RS232C cable. ます。 9. Press POWER Button to turn on the unit. 9. POWERボタンを押し、 Power On 状態にします。 The unit is in the boot mode.( LED and LCD display on (この状態より、...
Page 23
12. The Main microprocessor (QU01) has been Update. 12. 以上で、 書き込み作業は終了です。 13. Turn off Power switch, then disconnect FFC cable from 13. PM-15S2 の電源を切り、 FFC ケーブルを外します。 PM-15S2. 14. VERSION の確認を します。 4ページの "4. SERVICE MODE"で確認します。 Refer to "4. SERVICE MODE" on page 4.
+22V PRE AMP MAIN TRANS P-ON AC IN P-ON RELAY MUTE RELAY RELAY +24V LCD DISPLAY +15V DISPLAY μ -COM. SUB TRANS P-ON RELAY IR SENSOR DRIVER LED, RELAY IR SENSOR F.C.B.S. to PM-15S2 CONTROL POWER SW μ -COM. EEPROM...
Page 41
P209 A P211 A P211 B C991 B2 J871 B3 C992 A1 J872 B2 J991 A3 J992 A1 R991 A1 R992 A1 W991 B1 P209 B P212 A P212 B P210 A P210 B C891 A3 P213 A P213 B J891 A2 S891 B2 鉛フリー半田...
Page 47
SIDE ESC.(L/BL) 001D 00M04AJ257520 TOP COVER ASSY GOLD TOP COVER ASSY (GL) 029B 00M10AJ063140 ESCUTCHEON R GOLD ESCUTCHEON R GL PM-15S2 27AJ 001D 00M04AJ257520 TOP COVER ASSY GOLD TOP COVER ASSY (GL) 029B 00M10AJ063140 ESCUTCHEON R GOLD ESCUTCHEON R GL PM-15S2 27AJ...
Page 48
L001 101710040000M #POWER TRAN FOR PM-15S2 (230V) #POWER TRAN FOR PM-15S2 (230V) L001 101710040000M 101710040000M # POWER TRAN FOR PM-15S2 (230V) # POWER TRANS FOR PM-15S2 (230V) L001 101710040000M 101710040000M # POWER TRAN FOR PM-15S2 (230V) # POWER TRANS FOR PM-15S2 (230V)
12. MICROPROCESSOR AND IC DATA PD01 / QU01 : H8/3687...
Page 50
PD01 /QU01:H8/3687 SIGNAL PORT Functions Description NAME PB6_AN6 Left key A/D pin PB7_AN7 Model select AVcc AVCC Analog power supply Internal step-down power supply /RES Reset pin TEST TEST Test pin Connect to GND OSC2 OSC2 Main clock output OSC1 OSC1 Main clock input 8MHz...
Page 51
SIGNAL PORT Functions Description NAME P16_/IRQ2 PROT_2 Power supply error detect Active L(POW_OFF) P17_/IRQ3_TRGV PROT_1 DC/over current/Temp detect L_CS LCD-Controler(ST7032) CE Active L L_SCL LCD-Controler(ST7032) Serial Clock Out L_RS LCD-Controler(ST7032) Register Select H/L = Data/Instruction L_RES LCD-Controler(ST7032) Reset Active L(Reset) PB3_AN3 TEST1 PCB mode setting 1...
Page 53
P101 / Q501 : MAS6116 SO16 AGND AVCC ROUT LGND RGND RGND DGND ZERO PEAK DVCC CCLK CROSSING DETECTOR DATA XMUTE DATA CCLK CONTROL XMUTE ZERO PEAK CROSSING DETECTOR LOUT LGND AGND MAS6116 AVCC DVCC DGND Pin Name Type Function SO16 QFN 4x5 AVCC...
Page 54
PD01 / QU02 : AT24C08 PD01 / QU04 : 74HC4094 P101 / Q121, Q122 : 74HC4094 Q121 74HC4094 Port Name Function Description STOROBE DATA DATA CLOCK LINE_2 Line_2 input relay ON Active H REC_1 Recorder_1input relay ON Active H REC_2 Recorder_2 input relay ON Active H BI-AMP...
13. ELECTRICAL PARTS LIST NOTE ON SAFETY FOR FUSIBLE RESISTOR : PARTS INFORMATION The suppliers and their type numbers of fusible resistors RESISTORS are as follows; 1) 00MGD05 × × × 1. KOA Corporation 2) 00MGD05 × × × Part No. (MJI) Type No.
Page 56
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) HDAM-SA3 PWB(00MWG22AJ501-) 5501 DN01 00MHZ2001499Y 00MHZ2001499Y KDS122 TAPING 5501 DN02 00MHZ2001499Y 00MHZ2001499Y KDS122 TAPING 5501 DN03 00MHZ2001499Y 00MHZ2001499Y KDS122 TAPING 5501 DN04 00MHZ2001499Y 00MHZ2001499Y KDS122 TAPING 5501 JN01 00MYP07005670...
Page 57
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) P101 Q135 00D2690206908 00D2690206908 KRC102M KRC102M-AT/P (10K-10K) P101 Q161 00MHC10309030 00MHC10309030 LC78212 IC LC78212:CMOS LOGIC SANYO IC NJM2068DD:MONO ANA SHINNIHON P101 Q162 00MHC10053090 00MHC10053090 NJM2068DD MUSEN P101 Q163...
Page 58
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) TONE PWB(00MWG27AJ307-) P251 C251 00MOA22505021 00MOA22505021 2.2 UF M 50V RA-2 2.2 UF M 50V RA-2 P251 C252 00MOA22505021 00MOA22505021 2.2 UF M 50V RA-2 2.2 UF M 50V RA-2 P251 C253...
Page 59
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) LCH POWER AMP PWB(00MWA27AJ201-) P601 D601 00MHD20002001 00MHD20002001 1SS133 T-77 1SS133 T-77 P601 D602 00MHD20002001 00MHD20002001 1SS133 T-77 1SS133 T-77 P601 D603 00MHD20002001 00MHD20002001 1SS133 T-77 1SS133 T-77 P601 D604...
Page 60
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) P601 R645 00MGG0510216X 00MGG0510216X 1K OHM ± 5% 1/6W 1K OHM ± 5% 1/6W P601 R646 00MGG0510216X 00MGG0510216X 1K OHM ± 5% 1/6W 1K OHM ± 5% 1/6W P601 R647 00MGG0547216X 00MGG0547216X 4.7K OHM ±...
Page 61
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) P701 R733 00MGG0510116X 00MGG0510116X ! 100 OHM ± 5% 1/6W 100 OHM ± 5% 1/6W P701 R734 00MGG0510014X 00MGG0510014X ! 10 OHM ± 5% 1/4W 10 OHM ±...
Page 62
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) P851 C857 00MOA10605021 00MOA10605021 10 UF M 50V RA-2 10 UF M 50V RA-2 P851 C858 00MOA10605021 00MOA10605021 10 UF M 50V RA-2 10 UF M 50V RA-2 P851 C859 00MOA10605021...
Page 63
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) SPK OUT PWB(00MWA27AJ204-) P951 C901 00MOF55103581 0.01UF 100V ± 5% FNS 0.01UF 100V ± 5% FNS P951 C901 00MOF55103581 00MOF55103581 0.01UF 100V ± 5% FNS 0.01UF 100V ±...
Page 64
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) P991 R991 00MGG0547016X 00MGG0547016X 00MGG0547016X 47 OHM ± 5% 1/6W P991 R992 00MGG0547016X 00MGG0547016X 00MGG0547016X 47 OHM ± 5% 1/6W FCBS PWB(00MWG27AJ306-) PB01 CB01 00MDK9810420Y GRM39F104Z16 0.1UF MURATA GRM39F104Z16 0.1UF MURATA PB01...
Page 65
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) PD01 CU67 00MDK9610330Y 0.01UF ±10% 50V C1608JB1H103K 0.01UF ±10% 50V C1608JB1H103K PD01 CU71 00MDK9610330Y 0.01UF ±10% 50V C1608JB1H103K 0.01UF ±10% 50V C1608JB1H103K PD01 CU72 00MEG10601651 00MEG10601651 10UF/ 16V 10UF/ 16V...
Page 66
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) PD01 QU72 00MBA2130300Y 00MBA2130300Y DTC124EU RN1303 UMT TYPE DTC124EU RN1303 UMT TYPE PD01 QU73 00MBA2130300Y 00MBA2130300Y DTC124EU RN1303 UMT TYPE DTC124EU RN1303 UMT TYPE PD01 RD02 00MNN0533061Y 33 OHM ±...
Page 67
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) IR SENSOR PWB(00MWG27AJ302-) PD31 CD01 00MDK9810420Y GRM39F104Z16 0.1UF MURATA GRM39F104Z16 0.1UF MURATA PD31 CD02 00MDK9610230Y 1000 PF ± 10 % B 50V GR36 1000 PF ± 10 % B 50V GR36 PD31 CD03 00MDK9610230Y...
Page 68
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) PS01 C107 00MOF15101541 100PF J 100V APSV 100PF J 100V APSV PS01 C107 00MOF15101541 00MOF15101541 100PF J 100V APSV 100PF J 100V APSV PS01 C107 00MOF15101541 00MOF15101541 100PF J 100V APSV...
Page 69
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) PS01 C355 00MOA10605021 00MOA10605021 10 UF M 50V RA-2 10 UF M 50V RA-2 PS01 C356 00MOA10605021 00MOA10605021 10 UF M 50V RA-2 10 UF M 50V RA-2 PS01 C403 00MOF55102581...
Page 70
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) PS01 C509 00MOA226025Z1 00MOA226025Z1 ROS-25V 220M - F3#PE - T2 (22UF 25V) ROS-25V 220M - F3#PE - T2 (22UF 25V) PS01 C510 00MOA226025Z1 00MOA226025Z1 ROS-25V 220M - F3#PE - T2 (22UF 25V) ROS-25V 220M - F3#PE - T2 (22UF 25V) PS01 C511...
Page 71
VERS. PART NO. PART NO. POS. NO. PART NAME DESCRIPTION NAME COLOR (FOR EUR) (MJI) PS01 J608 00MYP07005670 00MYP07005670 IMSA-6065B-06Z065-PT1 IMSA-6065B-06Z065-PT1 PS01 J609 00MYP0600383X 00MYP0600383X B3B-EH-TS (LF)(SN) 3P RADIAL TAPING B3B-EH-TS (LF)(SN) 3P RADIAL TAPING PS01 J701 00MYP06003850 00MYP06003850 B2B-EH B2B-EH PS01 J705...
14. AFTER REPLACEMENT OF U-PRO OR FLASH ROM Pos. After PWB Name Description Remark replaced PD01 QU01 HD64F3687H FLASH After replaced A : Mask ROM (With software). No need write-in of software to the microprocessor. B : Flash ROM (With software). Usually, no need write-in of software. But, when the software was updated, you should be Refer to "Update procedure"...
Need help?
Do you have a question about the PM-15S2 and is the answer not in the manual?
Questions and answers