Features - D-Link xStack DES-3528P Hardware Installation Manual

®
xStack DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch User Manual
routers, switches and other networking devices. The dual speed ports use standard twisted-pair cabling and are ideal
for segmenting networks into small, connected sub networks for superior performance. Each 10/100 port can support
up to 200 Mbps of throughput in full-duplex mode.
In addition, the Switch has 2 SFP combo ports. These two-gigabit combo ports are ideal for connecting to a server or
network backbone. This stackable Switch enables the network to use some of the most demanding multimedia and
imaging applications concurrently with other user applications without creating bottlenecks. The built-in console
interface can be used to configure the Switch's settings for priority queuing, VLANs, and port trunk groups, port
monitoring, and port speed.

Features

•
IEEE 802.3 10BASE-T compliant
•
IEEE 802.3u 100BASE-TX compliant
•
IEEE 802.1p Priority Queues
•
IEEE 802.3x flow control in full duplex mode
•
IEEE 802.3ad Link Aggregation Control Protocol
support.
•
IEEE 802.1X Port-based and MAC-based Access
Control
•
IEEE 802.1Q VLAN
•
IEEE 802.1D Spanning Tree, IEEE 802.1W Rapid
Spanning Tree and IEEE 802.1s Multiple Spanning
Tree support
•
Access Control List (ACL) support
•
Single IP Management support
•
Access Authentication Control utilizing TACACS,
XTACACS and TACACS+
•
Dual Image Firmware
•
Simple Network Time Protocol support
•
MAC Notification support
•
Asymmetric VLAN support
•
System and Port Utilization support
•
System Log Support
•
Support port-based enable and disable
•
Address table: Supports up to 16K MAC addresses
per device
•
Supports a packet buffer of up to 1 Mbyte
•
High performance switching engine performs forwarding and filtering at full wire speed, maximum 14, 881 packets/sec on
each 10Mbps Ethernet port, and maximum 148,810 packet/sec on 100Mbps Fast Ethernet port.
•
Full- and half-duplex for both 10Mbps and 100Mbps connections. Full duplex allows the switch port to simultaneously
transmit and receive data. It only works with connections to full-duplex-capable end stations and switches. Connections to a
hub must take place at half-duplex
•
Support broadcast storm filteringF
•
Non-blocking store and forward switching scheme capability to support rate adaptation and protocol conversion
•
Supports by-port Egress/Ingress rate control.
•
Supports IP-MAC Port Binding.
•
Efficient self-learning and address recognition mechanism enables forwarding rate at wire speed
•
Supports STP Loopback Detection
•
Safeguard Engine Support
•
Supports Port-based VLAN Groups
•
Port Trunking with flexible load distribution and fail-
over function
•
IGMP Snooping support
•
SNMP support
•
Secure Sockets Layer (SSL) and Secure Shell
(SSH) support
•
Port Mirroring support
•
MIB support for:
•
RFC1213 MIB II
•
RFC1493 Bridge
•
RFC1907 SNMPv2 MIB
•
RFC1757, 2819 RMON
•
RFC2021 RMONv2
•
RFC1643, 2358, 2665 Ether-like MIB
•
RFC2233, 2863 Interface MIB
•
Private MIB
•
RFC2674 for 802.1p
•
RFC2618 RADIUS Authentication Client
•
RFC2620 RADIUS Accounting Client
•
RFC2925 Ping & Traceroute
•
IEEE 802.1X MIB
•
RS-232 DCE console port for Switch management
•
Provides parallel LED display for port status such as
link/act, speed, etc.
2