Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Panduit DP4X00H-CUT
Summary of Contents for Panduit DP4X00H-CUT
- Page 1 Instructions Cutter DP4X00H-CUT MADE IN GERMANY...
- Page 2 Edition: 09/2024 - Part No. DP4X00H-CUT-EN Copyright This documentation as well as translation hereof are property of Panduit Corporation. The replication, conversion, duplication or divulgement of the whole manual or parts of it for other intentions than its original intended purpose demand the previous written authorization by Panduit Corporation.
-
Page 3: Table Of Contents
Table of Contents Introduction ..................4 Instructions ..................4 Intended Use ...................5 Safety Instructions ................6 Environment ..................6 Mounting ..................7 Operation ..................9 Preparation ..................9 Standard Operation .................9 Cutting on Demand ................10 Adjusting Cutter Settings with Printer LCD ......11 Cleaning ..................13 Error Messages ................13 Licenses ..................14... -
Page 4: Introduction
Introduction Instructions Important information and instructions in this documentation are designated as follows: Danger! Draws attention to an exceptionally great, imminent danger to your health or life due to hazardous voltages. Danger! Draws attention to a danger with high risk which, if not avoided, may result in death or serious injury. -
Page 5: Intended Use
Introduction Intended Use • The device is intended exclusively as an option for the printers of the DP4300H, DP4600H, and DP4300HD series for cutting suitable materials that have been approved by the manufacturer. Any other use or use going beyond this shall be regarded as improper use. The manufacturer/supplier shall not be liable for damage resulting from unauthorized use;... -
Page 6: Safety Instructions
Introduction Safety Instructions • Disconnect the printer from the electrical outlet before mounting or removing the cutter. • The cutter may only be operated when it is mounted on the printer. • Risk of injury, particularly during maintenance, the cutter blades are sharp. •... -
Page 7: Mounting
Mounting Removing Covers Loosen screw (1) and remove cover (2). Mounting Cutter Tray Attention! For cutter operation there has to be mounted a tear-off plate or a dispense plate on the printer, to lead the material through the blades of the cutter. ... - Page 8 Mounting Mounting Cutter Attention! Disconnect the printer from the electrical outlet before mounting or removing the cutter. Insert the pins (3) of the cutter (5) into the holes (1) of the printer. Press the cutter against the printer. That way the plug of the cutter will be connected to the peripheral port (2) of the printer.
-
Page 9: Operation
Operation Preparation Insert labels for tear-off mode Refer to operation manual for more details. Place the media strip between the printhead and the drive roller, so that the front edge of the strip reaches through the cutter. Standard Operation ... -
Page 10: Cutting On Demand
Operation Cutting on Demand In the "Cut on Demand" mode the print job will be split into steps, which can be released separately. Choose Printing > Print on demand = On. 4. Adjusting Cutter Settings with Printer LCD. ... -
Page 11: Adjusting Cutter Settings With Printer Lcd
Adjusting Cutter Settings with Printer LCD Note! Cutter settings are for a specific printer and cutter combination. Changing the cutter may require re-adjustment to the cutter settings. Cutter control is handled by printing from Easy-Mark Plus labeling software. Cut Parameters ... - Page 12 Adjusting Cutter Settings with Printer LCD Print on demand Start menu. Select Setup > Printing. Parameter Meaning Default Print on Behavior between the cuts demand On: After cutting a label the next one will be printed and cut after touching Off: All labels will be printed and cut nonstop...
-
Page 13: Cleaning
Cleaning Warning! Disconnect the printer from the electrical outlet. Attention! Risk of injury. The cutter blades are sharp. 1. Remove the cutter from the printer. 2. Clean cutter with PTR-CLN cleaning kit. 3. Reattach cutter to printer. Error Messages Error message Cause Remedy... -
Page 14: Licenses
Licenses Reference to the EU Declaration of Conformity and other approvals: https://www.panduit.com/DP4X00H NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Need help?
Do you have a question about the DP4X00H-CUT and is the answer not in the manual?
Questions and answers