Subscribe to Our Youtube Channel
Related Manuals for Asada BEAVER4 ACTIVE
Summary of Contents for Asada BEAVER4 ACTIVE
- Page 1 BAND SAW BEAVER4 ACTIVE INSTRUCTION 【Read through this manual carefully before using the machine】...
-
Page 2: Table Of Contents
BEAVER4 ACTIVE BAND SAW SAFETY PRECAUTIONS Thank you for choosing our BAND SAW BEAVER 4ACTIVE. *This Instruction Manual must be retained by the user of this machine. *Read this Instruction Manual carefully and completely before use and thoroughly understand the usage, capacity, cautions, and easy repairs for correct operation. -
Page 3: Operating Instructions
BEAVER4 ACTIVE BAND SAW OPERATING INSTRUCTIONS ● Please observe “OPERATING INSTRUCTIONS” to prevent fire, electric shock or inquiry. ● Before using, please understand all the contents of “OPERATING INSTRUCTIONS” and follow the instructions. ● After reading this manual, please keep it so that you can take it out at any time. - Page 4 BEAVER4 ACTIVE BAND SAW WARNING -Wear caps or protective hair covering to contain long hair. Otherwise, you may get caught in moving parts. -When not in use or at servicing, cleaning, checking or replacing parts, turn off and unplug the machine.
- Page 5 BEAVER4 ACTIVE BAND SAW CAUTION -Watch the position of your fingers while lowering frame to avoid pinching of fingers. -Do not leave the machine with a long workpiece set on it. You may tumble and get injured. -Securely install accessories in accordance with this manual. Otherwise, accident or injury may result.
-
Page 6: Components Of The Machine
BEAVER4 ACTIVE BAND SAW COMPONENTS OF THE MACHINE Main Parts Tension Handle Motor Handle Frame Clamp Handle Switch Stopper Pin Blade Guide R Stop Bolt Overload Switch Blade Guide F Saw Blade Back Plate Clamp Lever... -
Page 7: Specifications
BEAVER4 ACTIVE BAND SAW Specifications Item BAND SAW BEAVER 4 ACTIVE Round φ120 ㎜ 0° Square □100 ㎜ Cutting Capacity Round φ50 ㎜ 45° Square □50 ㎜ No Load 75m/min （50/60Hz) Blade speed Cutting 45m/min （50/60Hz) Motor Valtage made to order Dimension（L×W×H）... -
Page 8: Saw Blade Selection Chart
BEAVER4 ACTIVE BAND SAW Saw Blade Selection Chart Under 1.1/4" 〇 Steel Pipe 1.1/2"～2.1/2" 〇 〇 (Size) 3"～4" 〇 Thin wall 〇 Conduit Pipe Thick wall 〇 Under 3.9 〇 Shaped Steel & Rods 4.0～4.9 〇 〇 （Thickness, mm） 5.0～... - Page 9 BEAVER4 ACTIVE BAND SAW...
-
Page 10: Installation
BEAVER4 ACTIVE BAND SAW INSTALLATION Carrying the Machine WARNING -When lifting the machine, bend your knees to avoid a load on your waist. -The machine with chip is slippery. Do not drop the machine on your feet while lifting it. - Page 11 BEAVER4 ACTIVE BAND SAW *1 Confirmation of Earth (Grounding) and Earth Leakage Circuit Breaker Before starting use of the machine, make sure that the power supply to which this machine will be connected is fitted with an earth leakage circuit breaker for prevention of electric shock (earth leakage circuit breaker) which conforms to the occupational safety and health law, electrical equipment technical standard, etc.
-
Page 12: Operation
BEAVER4 ACTIVE BAND SAW OPERATION Preparing for Operation CAUTION -Select a suitable Saw Blade for the workpiece, referring to Saw Blade Selection Chart. -Do not turn on the machine while Saw Blade is put on the workpiece. Otherwise, the machine may get failure. -When start cutting, Lower Saw Blade to the workpiece after Saw Blade has fully rotated. -
Page 13: Setting A Workpiece
BEAVER4 ACTIVE BAND SAW Setting a Workpiece 1. Pull out Frame to 90° and fix the Stopper Pin 90° position with Stopper Pin. Lock Workpiece On Vice 2. Place a workpiece on the vise surface in a stable position. Feed Screw Guide Tilt it 3. -
Page 14: Miter Cutting
BEAVER4 ACTIVE BAND SAW Miter Cutting 1. Turn Clamp Lever counterclockwise to Clamp Lever loosen the vise part. Loosen Clamp Lever 2. Turn the vise part to the desired angle Tighten and fix the position by turning Clamp Lever clockwise. -
Page 15: Cutting
BEAVER4 ACTIVE BAND SAW Cutting 1. Pull out Stopper Pin and unlock Frame. Stopper Pin Un Lock 2. Turn on the machine and check Saw Blade is rotating smoothly. Lower Frame and place Saw Blade on the workpiece. When miter cutting, hold Flame for a while until Saw Blade gets into the workpiece and stable. -
Page 16: Removing Workpiece
BEAVER4 ACTIVE BAND SAW Removing Workpiece 1. After cutting, raise Frame to 90° and Stopper Pin 90° Lock lock it with Stopper Pin. 2. Loosen Clamp Handle and remove the Clamp Handle Loosen workpiece. CAUTION -Immediately after cutting, cut surfaces are hot. Do not touch them with bare hands. -
Page 17: Cleaning After Use
BEAVER4 ACTIVE BAND SAW Cleaning After Use WARNING -Do not blow off chips using compressed air. They may get into eyes and loss of eyesight may result. -Chips are sharp. Do not touch them with bare hands. Always wear gloves. Remove chips scattered on the machine or in the area. -
Page 18: Maintenance & Inspection
BEAVER4 ACTIVE BAND SAW MAINTENANCE & INSPECTION Replacing Saw Blade WARNING -Before replacing Saw Blade, always unplug the machine. The machine may start suddenly, it may lead to injury. -When opening Back Plate, be careful with Saw Blade which may spring out of the machine. - Page 19 BEAVER4 ACTIVE BAND SAW 3. Open Back Plate and remove Saw Blade in the order D → C → B → A as the drawing. Remove 4. Install a new Saw Blade in the order A → B → C → D as the drawing.
-
Page 20: Replacing Pully Rubber
BEAVER4 ACTIVE BAND SAW Replacing Pulley Rubber WARNING -Before replacing Pulley Rubber, always unplug the machine. The machine may start suddenly, it may lead to an accident or injury. -When opening Back Plate, be careful with Saw Blade which may spring out of the machine. -
Page 21: Replacing Carbon Brush
BEAVER4 ACTIVE BAND SAW Replacing Carbon Brush WARNING Unplug the machine to avoid electric shock. CAUTION Do not get oil, chips, etc. on the new Carbon Brush. Do not get dirt of gloves, etc. on the new Carbon Brush. Motor has Carbon Brushes, which are Brush Cap consumable parts. -
Page 22: Daily Inspection And Maintenance
BEAVER4 ACTIVE BAND SAW Daily Inspection and Maintenance CAUTION Do not wet Motor with water. -If Power Plug, Power Cord or the extension cord is damaged, replace it immediately. -Check if Saw Blade get chipped or damaged. If Saw Blade is chipped or damaged, replace Saw Blade. -
Page 23: Before Asking For Repairs
BEAVER4 ACTIVE BAND SAW BEFORE ASKING FOR REPAIRS Trouble Possible Cause Solution When a new Saw Blade is used, it is liable to cut obliquely and test cuts must be required. Once oblique cutting occurred, it easily Test cuts are not enough. - Page 24 BEAVER4 ACTIVE BAND SAW Trouble Possible Cause Solution Saw Blade is chipped. Replace the Saw Blade. Vibration Improper Tension Handle Turn Tension Handle clockwise fully. during setting. cutting Back Plate is not closed Attach Back Plate correctly. correctly. Select Saw Blade matched the workpiece.
-
Page 25: Electrical Wiring Diagram
BEAVER4 ACTIVE BAND SAW ELECTRICAL WIRING DIAGRAM Switch Overload Motor Switch Earth Power Cord... - Page 26 BEAVER4 ACTIVE BAND SAW...
- Page 27 BEAVER4 ACTIVE BAND SAW...
- Page 28 ● Customer Memo Please fill in for your record in the future. The information is helpful for inquiry and ordering parts. Products Number： Date Purchased： Store Purchased the Unit： Ver.2 Code No. IM0617...
Need help?
Do you have a question about the BEAVER4 ACTIVE and is the answer not in the manual?
Questions and answers