Related Manuals for Asada BEAVER 10
Summary of Contents for Asada BEAVER 10
- Page 1 BEAVER 10 Band Saw INSTRUCTION MANUAL [Read through this manual carefully before using the machine]...
- Page 2 BEAVER 10 SAFETY PRECAUTIONS Thank you for choosing our Band Saw Beaver 10. *This Instruction Manual must be retained by the user of this machine. *Read this Instruction Manual carefully and completely before use and thoroughly understand the usage, capacity,cautions, and easy repairs for correct operation.
- Page 3 BEAVER 10 OPERATING INSTRUCTIONS -Always ground the machine to avoid electric shock or resultant death. -Do not touch the plug with wet hands. -Do not expose the machine to rain and water and do not use it in damp or wet locations.
- Page 4 BEAVER 10 -Before plugging the machine in, always make sure that the switch is OFF. If the machine remains plugged in, it will start suddenly, leading to unexpected accident or injury. -During operation, keep your hands and face away from the moving parts. You may be caught in the moving parts, causing injury.
- Page 5 BEAVER 10 -Keep proper footing and balance at all times. You may tumble and get hurt. -Do not operate the machine when you cannot concentrate on your work, e.g. when you are tired or while under the influence of alcohol, medication or drugs.
-
Page 6: Table Of Contents
BEAVER 10 -Do not let visitors touch the machine and Power Cord or operate the machine. -When not in use, machines should be stored in dry and high or locked up place - out of reach of children. CONTENTS 1. COMPONENTS OF THE MACHINE... -
Page 7: Components Of The Machine
BEAVER 10 1. COMPONENTS OF THE MACHINE 1) Main Parts Warning sticker is pasted on this machine. This sticker show how to keep safety, so keep it clean. If it peeled off or it’s printing disappeared, please petition our company to send new warning sticker. And affix new one on the same place. -
Page 8: Specifications
BEAVER 10 2) Specifications Item Band Saw Beaver 10 φ270 Cutting Round Pipe □200 capability Square Pipe Blade speed 0.72/0.90 m/s（50/60Hz） Motor Condenser motor, Voltage made to order, 50/60Hz,200W Machine dimension 1025×445×490 mm Weight (Net) 55 kg dimension / weight (Gross) 1200x580x690mm / 64kg 70446 Saw blade（14T.P.I Bimetal）... -
Page 9: 3-1) Saw Blade And Cutting Load Selecting Chart By Material
BEAVER 10 3-1) Saw Blade and Cutting Load Selecting Chart by material ●：H (Heavy) ◎：M (Medium) ○：H (Light) Bimetal Under 3/4” ○ ○ ○ ○ 1”-2 ” ○ ○ ○ ○ Galvanized 3”-4” ◎ ◎ ◎ ◎ Iron pipe 5”-6”... -
Page 10: Installation
BEAVER 10 2. INSTALLATION 1) Carrying the Machine -When lifting the machine, bend your knees to avoid a load on your waist. -The machine with chip is slippery. Do not drop the machine on your feet while lifting it. 2) Transport -Fix the machine in position so that it is stable and dose not move about while being transported. - Page 11 BEAVER 10 (1)Put the machine in a place free from moisture. (2)Put the machine on a flat surface without play or on a flat work bench. (3)Secure a sufficient space around the machine. A wide space is necessary particularly when working long and heavy pipe.
-
Page 12: Proper Working Environment
BEAVER 10 4) Proper working environment The working area should be put in order following the clauses in "OPERATING INSTRUCTIONS". Noise Prevention Control Noise is controlled as set forth in relevant regulations. The machine must be operated at less than the control value to avoid discomfort to the neighborhood. -
Page 13: Operation
Cut a workpiece once or twice at the cutting load position “ L”. -Install the saw blade after completely wiping oil and dirt off. -Use the genuine ASADA Band Saw Blade. -Band Saw Blade is sharp, so don’t hand with bare hands. -
Page 14: Adjustment Of Blade Guide F
BEAVER 10 2) Adjustment of Blade Guide F -Adjustment of the blade guide F will affect the cutting precision and life of the Saw blade. Blade Guide F (1) Loosen the Guide F adjustment Knob. (2) Set Blade Guide F as close as possible to the workpiece. -
Page 15: Adjustment Of Cutting Speed
BEAVER 10 4) Adjustment of cutting speed -Choose the T.P.I Blade, considering also shape of the materials. Refer to the Instruction manual p8 Saw Blade and Cutting Load Selecting Chart. -Operate the cutting speed which matches the workpiece. If you use wrong T.P.I Blade or wrong cutting speed, blade won’t work well and it will be broken. -
Page 16: Removing The Workpiece
BEAVER 10 6) Removing the Workpiece After cutting ends, removing the workpiece. *Loosen the Clamp Handle and unclasp chain. Next, remove the workpiece on the unit. -Immediately after cutting, fragment are hot. Do not touch them directly with hands. Wait for a while or hold the pipe with a cloth. Otherwise you may get burned. -
Page 17: Adjustment Of Up-Down Oblique Cutting
BEAVER 10 2) Adjustment of Up-down Oblique Cutting -Before correction for oblique cutting, always disconnect the power cord. The machine may start suddenly, leading to injury. *If the saw blade cuts obliquely, check for worn bearings in the blade guide heads. -
Page 18: Daily Inspection And Maintenance
BEAVER 10 (6)Loosen the two Bolts of Blade Guide and the Lock Nut of Blade Guide Head, and turn the adjustment bolt clockwise or counterclockwise to adjust the angle of the blade guide head. *When the top length is larger: Turn the adjustment bolt counterclockwise. - Page 19 BEAVER 10 *Check the blade stopper ball bearings and back stopper ball bearings. If they are not set correctly, cutting accuracy will decline. When the ball bearings are worn, replace them as soon as possible. (Replace all the bearings on both sides.) *Check for loose fitting screws of parts.
-
Page 20: Before Asking For Repairs
BEAVER 10 5. BEFORE ASKING FOR REPAIRS Trouble Possible Cause Solution When a new saw blade is used, it is liable to cut obliquely and test cuts must be made. If cut obliquely occurred, this saw blade will probably Test cuts not enough. - Page 21 BEAVER 10 Trouble Possible Cause Solution Tension handle not set in tightning Set the tension handle in the tightening position. direction. Installation of Back-Plate is bad. Move mounting position of Back-Plate Stopper. If blade guide F is really close to a workpiece, it may Vibration Adjustment of blade guide F.
-
Page 22: Electrical Wiring Diagram
BEAVER 10 6. ELECTRICAL WIRING DIAGRAM Switch Switch cord Overload protector Motor cord Motor Male Female Male Female Female Male Male Female Vise Power cord Earth... - Page 23 BEAVER 10...
- Page 24 CUSTOMER NOTE Please enter the following for future use. This note will be useful in making inquiries and placing purchase orders for part SERIAL NO, : DATE OF PURCHASE : SALES REPRESENTATIVE : Ver .05 Code No. IM0524 Ａ...
Need help?
Do you have a question about the BEAVER 10 and is the answer not in the manual?
Questions and answers