Do you have a question about the Elite AllergenSeal LITENING and is the answer not in the manual?
Questions and answers
Austin
March 15, 2025
Belt looks fine and hand mode works but floor mode is not working. Not spinning seems like it’s kind of sucking not really tho. I feel like it could be the connection in the back when I put the unit back in after using the handheld
1 comments:
Mr. Anderson
March 15, 2025
The floor mode on the Kenmore Elite AllergenSeal LITENING vacuum may not be working due to incorrect suction power settings, a low battery level, or an improper operation mode. Ensure the vacuum is set to BARE FLOOR mode and check if the suction power indicator (ECO, NORMAL, or BOOST) is illuminated. Also, verify that the battery is charged, as a low battery (below 10%) with a flashing red ring suggests recharging is needed. If the issue persists, refer to the troubleshooting section of the manual.
This answer is automatically generated
Related Manuals for Kenmore Elite AllergenSeal LITENING
Summary of Contents for Kenmore Elite AllergenSeal LITENING
Page 1
Use & Care Guide Manual de Uso y Cuidado Manuel d'entretien et d'utilisation Elite Cordless Upright Vacuum with ® Hair Eliminator Brushroll Aspiradora vertical inalámbrico con ® cepillo giratorio Hair Eliminator Aspirateur-balai sans fil avec ® rouleau brosse Hair Eliminator Model/Modelo/Modèle: CU7001 Vacuum Cleaner Help Line: 1-877-531-7321 (US) / 1-844-608-3081 (CA)
BEFORE USING YOUR NEW VACUUM CLEANER Read this Use & Care Guide. It will help you assemble and operate your new Kenmore vacuum cleaner in the safest and most effective way. For more information about vacuum cleaner care and operation, call the Vacuum Cleaner Help Line at 1-877-531-7321 (US) / 1-844-608-3081 (CA).
WITH PROOF OF SALE a defective product will be replaced free of charge. The Kenmore brand is used under license. Direct all claims for warranty service to: 1-877-531-7321 (US) / 1-844-608-3081 (CA). This warranty does not cover filters or belts, which are expendable parts that can wear out from normal use within the warranty period.
PARTS AND FEATURES Upper Hose Connection Handle Hose Release Button Handle Main Body Release Release Button Button Carrying Display Handle Screen Battery Battery Pack Compartment Dust Cup Dust Cup Release Lid Release Button Button Dust Cup Connection Hose Motorized Nozzle Headlight - 9 -...
Page 5
PARTS AND FEATURES Battery Pack Main Body Charging Base Handle Flexible Hose 3-in-1 Charging (Stored inside Combination Adapter the Main Tool (Stored Body) inside the Main Body) DISPLAY SCREEN Outer Ring Hose Status Indicator Suction Power Button Brushroll Status Suction Power Indicator Status Indicator Carpet / Bare...
Page 6
PARTS AND FEATURES CHARGING BASE Charging Pins Battery Compartment Accessory Storage - 11 -...
Before assembling the vacuum cleaner, check the PACKING LIST (Page 2). Use this list to verify that you have received all the components of your new Kenmore Cordless Upright Vacuum Cleaner. 1. Insert the handle into the main Battery body until you hear a ‘click’.
CHARGING NOTE: Please fully charge before first use. The battery pack can be charged through the charging base or charging adapter. The vacuum cleaner can be charged directly, with the battery 2. Optional: battery pack can pack installed, through the be charged directly through charging base.
Page 9
CHARGING 1. Insert the charging adapter 6. When the vacuum is fully into the charging port on the charged, the battery status will side of the charging base. indicate 100%. The outer ring will show a continuous blue 2. Ensure that the battery pack light.
OPERATING INSTRUCTIONS CAUTION Moving parts! To reduce the risk of personal injury, DO NOT touch the brushroll when vacuum is on. Contacting the brushroll while it is rotating can cut, bruise or cause other injuries. Disconnect electrical supply before servicing or cleaning the vacuum cleaner. Use caution when operating near children or pets.
Page 11
USING YOUR CORDLESS UPRIGHT VACUUM 4. Operate the vacuum cleaner by until the vacuum body is tilting the handle back towards locked in place. Disconnect the you and with the nozzle flush battery pack from the vacuum with the floor surface. cleaner.
Page 12
USING YOUR CORDLESS UPRIGHT VACUUM BRUSHROLL STATUS INDICATOR LIFT-UP MODE & HOSE STATUS INDICATOR 1. Place the vacuum cleaner in When there is a jam in the the upright locked position. brushroll, the brushroll status 2. Press the main body release indicator will flash red.
Page 13
USING YOUR CORDLESS UPRIGHT VACUUM 5. Press the handle release button and lift up the handle. Handle Release Button 4. Pull off the open end of the flexible hose from its storage slot to release the open end from the main body. To re-install, make sure the open end of the flexible hose is properly hooked onto the...
Page 14
USING YOUR CORDLESS UPRIGHT VACUUM 3-in-1 Combination Tool NOTE: The attachment also can insert directly into the hose if needed. 8. Press the On/Off button to turn on the vacuum cleaner. CAUTION When using attachments, be 9. Once you have completed careful not to over extend the vacuuming, press the On/Off flexible hose when reaching.
Page 15
ATTACHMENTS All included attachment tools Press the release button to can be inserted into either the remove the brush tool. Set the handle or the flexible hose. combination tool in dusting brush mode as shown. Use in 3-IN-1 COMBINATION TOOL dusting brush mode for cleaning loose surfaces such as drapes.
ATTACHMENT USE TABLE CLEANING AREA = Applicable Between ATTACHMENT Stairs Furniture* Cushions* Drapes* Baseboards Carpet Bare CREVICE TOOL DUSTING BRUSH UPHOLSTERY BRUSH *Always clean attachments before using on fabrics. PERFORMANCE/SAFETY FEATURES THERMAL PROTECTOR CAUTION This vacuum cleaner has Always return the vacuum a thermal protector which cleaner to the upright position automatically trips to protect the...
PERFORMANCE/SAFETY FEATURES ® Hair Eliminator Brushroll BRUSHROLL RESET For best performance, the To prevent motor damage from motorized nozzle is equipped jams, the brushroll features built- ® with a hair eliminator brushroll, in overload protection. If the which prevents build-up of hair, brushroll encounters a blockage, string and other debris on the it will slow down or stop...
VACUUM MAINTENANCE AND CARE Always follow all safety precautions when performing maintenance to the vacuum cleaner. WARNING WARNING The motorized nozzle is Electrical Shock and Personal equipped with sharp comb Injury Hazard teeth inside. DO NOT touch comb teeth when servicing or Disconnect the battery pack cleaning the vacuum, which before servicing or cleaning the...
Page 19
EMPTYING DUST CUP 3. Position dust cup over a waste WARNING receptacle. Press down on the dust release button to open Disconnect the battery pack dust cup lid and allow contents before performing any service on vacuum cleaner. to drop into waste receptacle. NOTE: For best performance, empty dust cup after every use.
PRE-FILTER CLEANING The pre-filter is located inside 3. Lift up the pre-filter from the the dust cup. Clean the pre-filter dust cup. Clean pre-filter by as needed to optimize suction gently tapping over a waste receptacle. Tap on several sides power.
Page 21
FOAM AND FELT FILTERS CLEANING IMPORTANT: 3. Wash with cold water only, DO Clean filters NOT use detergent or soap. every month. Foam filters may Squeeze by hand and allow to appear dirty after use - this is air dry. Allow all filters to dry 24 normal.
Page 22
HEPA MEDIA EXHAUST FILTER CLEANING IMPORTANT: 4. Press the release tab and Clean the filter remove the HEPA media every month. Do not operate exhaust filter from vacuum without the filter! main body. It is recommended to clean the HEPA media exhaust filter with cold water every month.
Need help?
Do you have a question about the Elite AllergenSeal LITENING and is the answer not in the manual?
Questions and answers
Belt looks fine and hand mode works but floor mode is not working. Not spinning seems like it’s kind of sucking not really tho. I feel like it could be the connection in the back when I put the unit back in after using the handheld
The floor mode on the Kenmore Elite AllergenSeal LITENING vacuum may not be working due to incorrect suction power settings, a low battery level, or an improper operation mode. Ensure the vacuum is set to BARE FLOOR mode and check if the suction power indicator (ECO, NORMAL, or BOOST) is illuminated. Also, verify that the battery is charged, as a low battery (below 10%) with a flashing red ring suggests recharging is needed. If the issue persists, refer to the troubleshooting section of the manual.
This answer is automatically generated