Page 1
IN240500276V01_US 820-422V83_820-422V82_820-422V81 820-422V80 ELECTRIC HEATER INSTRUCTION MANUAL Models: W914-36F, W914-40F, W914-50F and W914-60F ATTENTION: 1. Keep this electric heater away from direct sunlight. 2. Before plugging in the electric heater, read all instructions. US_CA...
IMPORTANT SAFETY INSTRUCTIONS Keep this manual for future reference. WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING THE FOLLOWING: Read all instructions before using this heater. Failure to follow these important safety instructions may cause fire, electric shock or damage.
To avoid extreme room temperatures, do not leave the product running unattended, especially around small children or individuals with reduced physical, sensory or mental capabilities. CAUTION: Procedures and techniques, if not carefully followed, can result in damage to the equipment, property or personal injury. WARNING: Procedures and techniques, if not carefully followed, can expose the user to the risk of serious injury, illness or death.
INSTALLATION Caution: Before installation, remove the fixing screws on the top plate. (W914-36F/ W914-40F/W914-50F) (W914-60F) NOTE: This heater offers two installation options, which can be selected based on your preference. Installation 1: Built-in wall Clearance: Maintain a minimum spacing of 0.5 inches between the rear of the unit and the wall.
Page 5
Step 1: (1) Locate and remove the two mounting screws. (2) Pull the front cover upwards to remove it (see figures below). Fig. A (1) Fig. A (2) Step 2: Using four screws, secure the unit to the wall (see figure below). Fig.
Page 6
Step 3:Replace the front cover and secure it with two mounting screws (see figure below). Fig. C Installation 2: Wall hanging Step 1: Choose the wall location for hanging your electric heater. Use a level to draw a horizontal line and mark four drill holes for the anchor screws. Note: The drill holes are for mounting the heater –...
Page 7
Step 3: Using four anchor screws and four washers, attach the mounting bracket to the wall (see figure below). Fig. C Step 4: (1) Locate and remove the two mounting screws. (2) Pull the front cover upwards to remove it (see figures below). Fig.
Page 8
Step 6: Using two mounting screws, secure the mounting bracket to the heater (see figure below). Fig. F Step 7:Attach the front cover and secure it with two mounting screws (see figure below). Fig. G...
Page 9
REPLACING DECORATIVE ROCK Step 1: (1) Locate and remove the two mounting screws. (2) Pull the front cover upwards and remove it (see figure below). Fig. A (1) Fig. A (2) Step 2: Place the rock or branch into the heater (see figure below). Fig.
Step 3: Attach the front cover and secure it with two mounting screws (see figure below). Fig. C CAUTION: Before operating the unit, ensure all screws are tightened. OPERATION After reading all the instructions, ensure the fireplace controls are in the OFF position.
The controls are on the right side of the unit. : Press this button to turn the fireplace on. Press it again to turn it off. Once the fireplace is turned off, the fan will continue to operate for 60 seconds without heat.
Page 12
1 CR2025 batteries required (NOT INCLUDED) : Press this button to turn the fireplace on. Press it again to turn it off. Once the fireplace is turned off, the fan will continue to operate for 60 seconds without heat. : P r e s s t h i s b u t t o n t o t o g g l e b e t w e e n t h e t w o temperature scales.
1.) Battery type:CR2025 2.)Nominal Vlotage 3V Battery a) Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate. b) Even used batteries may cause severe injury or death. c) Call a local poison control center for treatment information.
Need help?
Do you have a question about the 820-422V83 and is the answer not in the manual?
Questions and answers