1. Manuals
  2. Brands
  3. CSC Manuals
  4. Motorcycle
  5. RX6
  6. Owner's manual

CSC RX6 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
RX6
Owner's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RX6 and is the answer not in the manual?

Questions and answers

Related Manuals for CSC RX6

Summary of Contents for CSC RX6

  • Page 1 Owner’s Manual...
  • Page 2 Preface The motorcycle can be used on road only and by one driver with only one passenger. The user should read the user’s manual carefully before using the product. The user shall have a proper command of basic operation functions, usage methods and other common sense for the model. The data descriptions, technical specifications, and performance parameters labeled in the manual are compiled based on the latest status.

  • Page 3: Security Information

    Caution any misoperation. The most efficient service information is available for faster warranty service and more Suggestion understandable instructions. CSC Motorcycles: 1331 W Foothill Blvd, Azusa, CA 91702 Customer service hotline: 4007003088 For more information, please visit our website: www.cscmotorcycles.com...

  • Page 4: Table Of Contents

    Table of contents Preface Operation of new motorcycle Security information Safe driving guidance Content Periodic maintenance schedule Caution Inspection and replacement of engine oil Vehicle identification code (VIN) and engine Cleaning of air filter number Inspection and adjustment of spark plug Introduction of the whole motorcycle Adjustment of accelerator cable Ignition lock...

  • Page 5: Instruction To Users

    Instruction to users Caution Please read this manual carefully before using the motorcycle! Caution Danger 1. After unpacking, please check the attached accessories and various 1. Strictly abide by traffic regulations. data according to the packing list. 2. . It is prohibited to drive a motorcycle without a motor vehicle license 2.

  • Page 6: Vehicle Identification Code (Vin) And Engine Number

    Instruction to users Vehicle identification code (VIN) and engine number Vehicle identification number (VIN), engine number and vehicle certificate are used to apply for driving license and motorcycle account. 1. The vehicle identification number 2. The vehicle nameplate is riveted on 3.

  • Page 7: Introduction Of The Whole Motorcycle

    Instruction to users Introduction of the whole motorcycle 1. Rearview mirror 2. Left steering handle 3. Left switch combination 4. Instrument assembly 6. Right switch 5. Ignition lock 7. Refueling handle 8. Fuel tank lock combination...
  • Page 8 Instruction to users Introduction of the whole motorcycle 6. Left rear pedal 7. Rear armrest 1. Headlamps 2. Front shock absorber 3. Seat cushion 4. Shift arm 5. Left front pedal...
  • Page 9 Instruction to users Introduction of the whole motorcycle 1. Tail light 2. Fuel tank 3. Rear wheel 4. Exhaust muffler 5. Right rear pedal 6. Right front pedal 7.Rear brake pedal 8. Front wheel...
  • Page 10 Instruction to users Ignition lock The ignition switch mainly controls the ignition circuit and lighting circuit, and its operation is as follows: Name Function description Unlock the key within one meter from the vehicle, press the start switch down once, the whole vehicle will be powered Keyless start on, press and hold the start switch down, and the engine will be ignited.

  • Page 11: Instrument Indicator

    Instruction to users Instrument indicator Name Function description The main indication functions of the Display the current fuel volume, vehicle instrument panel are as follows: speed, water temperature, gear, time, 1. TFT display temperature, battery, voltage, average fuel consumption speed and mileage, etc.

  • Page 12: Left Handle Switch

    Instruction to users Left handle switch Name Use instruction Short press to switch the main interface of The main functions of the left handle different styles. Long press (2s) in the sub switch are as follows: 1. MODE: key interface to return to the superior menu When the lighting switch button is pressed to the “...

  • Page 13: Right Handle Switch

    Instruction to users Right handle switch The main functions of the right handle switch are as follows: Name Use instruction When the switch is set to the " " position, the motorcycle will quickly turn 1. Flameout off. When the switch is set to the" "...

  • Page 14: Fuel Tank

    Instruction to users Fuel tank The fuel tank has a capacity of 5.5 gallons and uses unleaded gasoline ≥95. Name Use instruction Hold the key and turn it clockwise to open 1. Fuel tank (ON) the fuel tank cap Align the fuel tank cap with the filler and 2.

  • Page 15: Control Part

    Instruction to users Control part The brakes of this model are equipped with front and rear disc brakes, and the braking performance is reliable. Braking is related to personal and property safety and must be regularly and correctly adjusted and maintained to achieve the goal of safe driving.
  • Page 16 Instruction to users Control part Name Use instruction This motorcycle adopts a six-speed transmission mode with constant engagement two-stage 4. Speed change transmission. Please reduce the pedal accelerator when shifting gears. The shifting way is shown in the left figure. Suggestion 1.
  • Page 17 Instruction to users Control part Name Use instruction It controls the amount of mixed gas flow, 5. Refueling and its free stroke is: 2 mm~6 mm. handlebar The accompanying tools are under the front and rear seat cushions, which are suitable for some simple adjustment and maintenance during use.

  • Page 18: Load Limit

    Instruction to users Load Limit This model is designed to carry only one driver and one passenger. Please strictly follow the following requirements, otherwise the safety and stability of the motorcycle will be affected. Factory-determined maximum payload of the finished vehicle : 330 lbs.

  • Page 19: Efi System

    Instruction to users EFI System if there is no fault, please check according to the following The main function of the EFI system is to atomize the fuel contents: supplied from the fuel tank, mix it with air to form a uniform 1.
  • Page 20 Instruction to users EFI System Structural schematic diagram of EFI system Idle control valve 24X crankshaft Throttle position position target Crankshaft position sensor Optional sensor wheel Burglar alarm Throttle valve body Heated oxygen Optional sensor L Ignition coil Heated oxygen sensor R Engine Engine control...
  • Page 21 Instruction to users EFI System Function introduction and installation location diagram of EFI parts 3. Nozzle: atomize the fuel and inject it into the 1. Engine electronic control unit (ECU): collect, process combustion chamber of the engine information and issue instructions 2.
  • Page 22 Instruction to users EFI System Function introduction and installation location diagram of EFI parts 5. Intake pressure temperature sensor: test Intake 7. Oxygen sensor: measure oxygen content in exhaust pressure, intake temperature and atmospheric pressure 8. Crankshaft position sensor: measure the crankshaft position, which is ECU 6.
  • Page 23 Instruction to users EFI System Function introduction and installation location diagram of EFI parts 9. Thermostat: senses the temperature of engine cooling water Caution 1. It is strictly forbidden to disassemble the ECU and other EFI components while the whole vehicle is charged. 2.

  • Page 24: Inspection Before Driving

    Operation guide Inspection before driving Before driving, check in accordance with the following requirements to ensure users' safe driving and successful driving. Items Check Remark Fuel system Inspect the fuel capacity and fuel valve for oil leakage Check whether the lubricating oil is deteriorated and whether the capacity Lubricating oil is lower than the lower scale line Check whether the power supply and energization of the electrical parts of...

  • Page 25: Starting And Preheating

    Operation guide Starting and preheating During electric starting, the starting time shall not exceed 5s each time, and the interval shall not be less than 10s each time. If the starting cannot be successful for 3 consecutive times, check it. Cold car startup and preheating steps are as follows: 1.
  • Page 26 Operation guide Starting and preheating 3. Press the electric start button with the thumb of your right hand. 4. Do not refuel when starting the motorcycle; After startup, warm up for 3~5 minutes at 1500 (1 ± 10%) rpm at idle speed. Only after the motorcycle is warmed up can it run normally.

  • Page 27: Driving Operation

    Operation guide Driving operation 1. After starting preheating, retract the side support, hold the clutch handle and disengage the clutch. Press the shift arm with the left toe (Note: the brake is in braking state before starting and engaging gear), and shift the gear to the first gear.

  • Page 28: Operation Of New Motorcycle

    Change the company's special oil every 200 miles. In case of any engine failure during the running- in period and trial operation, please contact CSC Motorcycles special maintenance service center. 1. 0 miles～100 miles： During driving, the speed shall be controlled at about 4,000 RPM, and the refueling hand shall control the stroke at about 1/4.

  • Page 29: Safe Driving Guidance

    Operation guide Safe driving guidance 1. Precautions for driving up and down ramps When driving on mountain roads with twists and turns and undulating slopes, the driving speed shall be adjusted according to the actual situation to avoid overloading the engine. ①...
  • Page 30 Operation guide Safe driving guidance 4. Precautions for driving braking The higher the speed of the motorcycle, the longer the braking distance. Therefore, during braking, the brake shall be controlled according to the vehicle speed and the required braking distance. ①.

  • Page 31: Periodic Maintenance Schedule

    Maintenance Periodic maintenance schedule Odometer km Maintenance times Running-in period Initial stage Every Maintenance items Remark 500 miles or 1 month 1,500 miles or 3 months 3,000 Miles Valve clearance ※ No inspection without fault Spark plug ※ No inspection without fault Air filter ※...

  • Page 32: Inspection And Replacement Of Engine Oil

    Maintenance Inspection and replacement of engine oil Change the oil regularly; please do so after a few minutes of preheating and change the oil strictly according to the standards specified by the company. 1. Place the engine horizontally, idle for 60 seconds and then stop for 3 minutes to check the oil level.
  • Page 33 Maintenance 3. Remove the oil plug on the right cover, add lubricating oil of corresponding brand from the oil plug of the right cover, pay attention to the height of the oil scale while adding oil, and stop refueling until the oil level reaches the upper line of the oil scale.

  • Page 34: Cleaning Of Air Filter

    Maintenance Cleaning of air filter After the filter element of the air filter is blocked by dust, the resistance of the intake system will increase, the mixture is too rich, the power will decrease and the fuel consumption will increase. Therefore, the filter element should be checked, cleaned and replaced regularly.

  • Page 35: Inspection And Adjustment Of Spark Plug

    Maintenance Inspection and adjustment of spark plug Remove the spark plug. When the skirt of the spark plug insulator is gray white, it indicates that the engine is overheated. It is because the calorific value of the spark plug is small or the spark plug is screwed in too long. Replace the spark plug with the same type.

  • Page 36: Adjustment Of Accelerator Cable

    Maintenance Adjustment of accelerator cable Adjust the throttle wire pull rope by turning the adjusting nut to achieve the correct free stroke of the throttle handle. 1. When the free stroke of the throttle handle is greater than or less than the standard value, it needs to be readjusted. 2.

  • Page 37: Inspection And Adjustment Of Front Brakes

    Maintenance Inspection and adjustment of front brakes The front brakes of this model are equipped with disc configuration, which has the advantages of stable braking performance, safety, reliability, labor saving, good heat dissipation, etc. 1. When the free travel of the current brake handle is greater than or less than the standard value, it needs to be adjusted again.

  • Page 38: Adjustemnt Of Rear Brakes

    Maintenance Inspection and adjustment of rear brakes 1. The free stroke of the rear brake pedal can be adjusted through the limit screw of the brake arm so that the free travel of the rear brake pedal is a standard value. Pedal the rear brake pedal several times, then release and rotate the rear wheel assembly to check whether the rear wheel can rotate freely.

  • Page 39: Inspection Of Wheels

    Maintenance Inspection of Outer tire wear limit value wheels Front wheel 2.0mm Outer tire wear limit value Rear wheel 3.0mm Wheel deflection limit value Axial direction 2.0mm Wheel deflection limit value Radial direction 2.0mm Danger 1. If the tire pressure is too high, the riding comfort will be reduced and the wear of various parts will be accelerated.

  • Page 40: Battery

    Maintenance Battery This motorcycle adopts wet charged colloidal battery with DC power supply, and its ready-to-use specification is YTZ12S-BS（ 12V11Ah). Battery (wet charge type) The valve controlled wet charge maintenance free lead-acid battery does not need to inject liquid into the battery.

  • Page 41: Replacement Of Fuse Tube

    Maintenance Replacement of fuse tube Adjustment of electric horn The battery is charged and discharged with a fuse in series. After the motorcycle has been running for a period of When the current exceeds the specified value, the fuse will time, the fixing nut and adjusting screw of the electric automatically break to protect the battery and electrical horn may become loose, resulting in hoarseness or...

  • Page 42: Common Faults Of Efi System

    Maintenance Common faults of EFI system No. Failure phenomenon Cause of failure The whole vehicle without 1. The fuse is broken or loose; 2. Loose connection of positive and negative electrodes electricity or the EFI system of battery; 3. The key lock and flame-out switch loose; 4. The ground wire is loose; 5. without electricity.

  • Page 43: Cleaning And Storage

    Maintenance Cleaning and storage 1. Cleaning of the motorcycle (1). Before cleaning the vehicle, block the tail of the exhaust pipe, and then clean the dust and dirt with a high-pressure water gun. Note that the pressure of the high-pressure water gun cannot be too high, otherwise the lubricating grease will be washed clean (such as wheel bearing, steering column bearing, oil seal, etc.).

  • Page 44: Electrical Schematic Diagram

    Electrical schematic diagram...

  • Page 45: Technical Specifications And Performance Parameters

    Technical specifications and performance parameters Items Specifications/parameters Outer contour dimension (length × width × height) 7.2 ft × 2.7 ft × 4.6 ft Wheelbase 4.75 ft Minimum ground clearance 0.55 ft Minimum turning circle diameter 17 ft Complete vehicle curb mass 540 lbs Maximum capacity 330 lbs...
  • Page 46 Technical specifications and performance parameters Items Specifications/parameters Tyre size/air pressure Rear tire 160/60-17M/C/36 psi or 160/60ZR17M/C/36 psi...
  • Page 47 Memorandum...
  • Page 48 All Rights Reserved Format 140mm×102mm First Edition January 2022 First printing in January 2022...

Table of Contents