1. Manuals
  2. Brands
  3. elsner elektronik Manuals
  4. Weather Station
  5. Suntracer KNX sl basic
  6. Technical specifications and installation instructions

elsner elektronik Suntracer KNX sl Technical Specifications And Installation Instructions

Hide thumbs Also See for Suntracer KNX sl:
Table of Contents

Advertisement

Quick Links

Download this manual
Suntracer KNX sl
Weather Station
Technical specifications and installation instructions
Item number 70154
EN
Elsner Elektronik GmbH Control and Automation Engineering
Sohlengrund 16
75395 Ostelsheim
Germany
Phone +49 (0) 70 33 / 30 945-0 info@elsner-elektronik.de
Fax
+49 (0) 70 33 / 30 945-20 www.elsner-elektronik.de
Technical support: +49 (0) 70 33 / 30 945-250

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Suntracer KNX sl and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for elsner elektronik Suntracer KNX sl

Summary of Contents for elsner elektronik Suntracer KNX sl

  • Page 1 Suntracer KNX sl Weather Station Technical specifications and installation instructions Item number 70154 Elsner Elektronik GmbH Control and Automation Engineering Sohlengrund 16 75395 Ostelsheim Phone +49 (0) 70 33 / 30 945-0 info@elsner-elektronik.de Germany +49 (0) 70 33 / 30 945-20 www.elsner-elektronik.de...
  • Page 2 1-bit or 2 x 8-bit • 8 multi-function modules (computers) for changing the input data by calculations, by querying a condition or by converting the data point type Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.

  • Page 3: Technical Specification

    Resolution 0.1°C Accuracy ±0.5°C at -30°C … +25°C ±1.5°C at -30°C … +45°C Wind sensor: Measurement range 0 m/s … 35 m/s Resolution 0.1 m/s Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.

  • Page 4: Installation And Start-Up

    After unpacking the device, check it immediately for possible mechanical damage. If it has been damaged in transport, inform the supplier immediately. Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.

  • Page 5: Installation Location

    There must be at least 60 cm clearance to oth- er elements (structures, construction parts, etc.) below, to the sides and in front of the de- vice. 60 cm Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.
  • Page 6 For installation in the northern hemisphere, the device must be aligned to face south. North For installation in the southern hemisphere, the device must be aligned to face north. South Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.

  • Page 7: Device Design

    Even a few drops of water can damage the device electronics. • Do not open the device if water (e.g. rain) can get into it. Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.

  • Page 8: Preparation For Installation

    Use fixing materials (dowels, screws) that are suitable for the base. Fig. 8 The device is installed with two screws. Break off the two longitudinal holes in the lower part of the housing. Longitudinal holes Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.
  • Page 9 ATTENTION! The printout of the data sheet does not have original size! A separate, di- mensionally correct drilling plan is included ex works and this can be used as a tem- plate. Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.
  • Page 10 Feed the power lead through the rubber gas- ket. Rubber gasket Cable guide 2.4.3. Connection The connector is in the lower part of the housing. Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.

  • Page 11: Closing The Installation

    Remove all transport protection stickers present after installation. The wind measurement value and thus also all wind switching outputs cannot be out- put until 35 seconds after the power is turned on. Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.

  • Page 12: Addressing The Equipment

    (e.g. moving windows/awnings if a rain/wind alarm has been triggered while cleaning). • Always isolate the device from the mains for servicing and cleaning. Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.
  • Page 13 ATTENTION The device can be damaged if water penetrates the housing. • Do not clean with high pressure cleaners or steam jets. Weather Station Suntracer KNX sl • Status: 14.07.2016 • Errors excepted. Subject to technical changes.

This manual is also suitable for:

70154

Table of Contents