elsner elektronik Suntracer KNX-GPS Technical Specifications And Installation Instructions
Hide thumbs
Also See for Suntracer KNX-GPS:
- Installation and adjustment (40 pages) ,
- Technical specifications and installation instructions (2 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for elsner elektronik Suntracer KNX-GPS
Summary of Contents for elsner elektronik Suntracer KNX-GPS
- Page 1 Suntracer KNX-GPS Weather Station Technical specifications and installation instructions Elsner Elektronik GmbH Control and Automation Engineering Herdweg 7 D – 75391 Gechingen Phone +49 (0) 70 56 / 93 97-0 info@elsner-elektronik.de Germany +49 (0) 70 56 / 93 97-20 www.elsner-elektronik.de...
-
Page 2: Technical Data
Elsner Elektronik home- page on www.elsner-elektronik.de in the “Service” menu. 1.1. Technical data Housing Plastic Colour White / Translucent Mounting Surface-mounted Protection rating IP 44 Weather Station Suntracer KNX-GPS • Date of issue: 30.03.2011 • Errors excepted. Subject to technical changes. - Page 3 EN 60730-1:2000 Section EMV (23, 26, H23, H26) (threshold category: B) • EN 50090-2-2:1996-11 + A1:2002-01 (threshold category: B) • EN 61000-6-3:2001 (threshold category: B) Weather Station Suntracer KNX-GPS • Date of issue: 30.03.2011 • Errors excepted. Subject to technical changes.
-
Page 4: Installation And Commissioning
Please take note that an extended awning does not shade the device from sun and wind. Weather Station Suntracer KNX-GPS • Date of issue: 30.03.2011 • Errors excepted. Subject to technical changes. - Page 5 The weather station comes with a combination wall/pole mount. The mount comes ad- hered by adhesive strips to the rear side of the housing. Fasten the holder vertically to the wall or pole. Weather Station Suntracer KNX-GPS • Date of issue: 30.03.2011 • Errors excepted. Subject to technical changes.
- Page 6 With the hinge arm mounting, the weather stati- on projects from beneath the roof overhang. Sun, wind and precipitation can act upon the sensors without hindrance. Weather Station Suntracer KNX-GPS • Date of issue: 30.03.2011 • Errors excepted. Subject to technical changes.
-
Page 7: Rear View And Drill Sketch
Dimensions of the rear side of the housing with holder, dimensions in mm. Diver- gences are possible for technical reasons. Oblong hole 7,5 x 5 mm Weather Station Suntracer KNX-GPS • Date of issue: 30.03.2011 • Errors excepted. Subject to technical changes. -
Page 8: Preparing The Weather Station
Lead the cable for the voltage supply and bus connection through the rubber seals on the bottom of the weather station and connect Voltage L/N and Bus +/- to the terminals provided. Weather Station Suntracer KNX-GPS • Date of issue: 30.03.2011 • Errors excepted. Subject to technical changes. -
Page 9: Layout Of The Circuit Board
Close the housing by putting the cover back over the bottom part. The cover must snap in on the left and right with a definite “click”. Weather Station Suntracer KNX-GPS • Date of issue: 30.03.2011 • Errors excepted. Subject to technical changes. -
Page 10: Notes On Mounting And Commissioning
The sensor must regularly be checked for dirt twice a year and cleaned if necessary. In case of severe dirt, the sensor may not work properly anymore. Weather Station Suntracer KNX-GPS • Date of issue: 30.03.2011 • Errors excepted. Subject to technical changes. - Page 11 Maintenance As a precaution, the device should always be separated from power supply for maintenance works (e.g. deactivate or remove fuse). Weather Station Suntracer KNX-GPS • Date of issue: 30.03.2011 • Errors excepted. Subject to technical changes.
Need help?
Do you have a question about the Suntracer KNX-GPS and is the answer not in the manual?
Questions and answers