Clavia Nord Lead 3 Owner's Manual page 69

NORD LEAD 3 V1.2x
F F F F
I I I I N N N N E E E E T T T T U U U U N N N N E E E E
The F knob is for fine tuning Oscillator 2. The Fine parameter operates within one semitone, +/- 0.5
INE
semitones. If you set Oscillator1 and 2 to equal volume (see Osc Mix below) and Oscillator 2 to '0' Coarse
tune value, and raise or lower the Fine parameter slightly, the slight difference in pitch will make the
sound "richer".
Range: +/- 0.5 semitones in 128 steps.
C C C C
O O O O A A A A R R R R S S S S E E E E T T T T U U U U N N N N E E E E
The C knob is used to adjust the coarse tuning of Oscillator 2, relative to Oscillator 1. The range
OARSE
is from 5 octaves below Oscillator 1 to 5 octaves above Oscillator 1, i.e. 10 octaves. If you press the P
N button, you can set the Oscillator 2 coarse tune in partials rather than in semitones. To aid you
TIAL O
in setting the value, the LED
Range: +/- 5 octaves in steps of 1 semitone or in steps of partials.
Note: Depending on the Oct Shift setting (see
dible.
T T T T P P P P LED D LED D LED D LED D
H H H H E E E E I I I I T T T T C C C C H H H H
The LED D
ISPLAY
frequencies of Oscillator 2. This can be displayed in a number of different ways:
D D D D
I I I I S S S S P P P P L L L L A A A A Y Y Y Y O O O O F F F F S S S S E E E E M M M M I I I I T T T T O O O O N N N N E E E E S S S S F F F F O O O O R R R R W W W W A A A A V V V V E E E E F F F F O O O O R R R R M M M M S S S S
This is the default way of displaying the Oscillator 2 pitch when the P
functions are not activated. The semitone value is displayed the same way for every waveform except for
Dual Sine and Dual Sine FM. The semitone figure is relative to the pitch of Oscillator 1. In the pictures
below, the middle C (C4) note is our reference note. If you turn the C
D will increment or decrement in steps of 1 semitone. The range is -63 to 63 semitones in steps
ISPLAY
of 1 semitone.
D D D D
I I I I S S S S P P P P L L L L A A A A Y Y Y Y O O O O F F F F P P P P A A A A R R R R T T T T I I I I A A A A L L L L S S S S F F F F O O O O R R R R W W W W A A A A V V V V E E E E F F F F O O O O R R R R M M M M S S S S
When the P
ARTIAL
semitones. The partial value is displayed the same way for every waveform except in Dual Sine mode. The
partial figure is relative to the pitch of Oscillator 1. In the picture below, the middle C (C4) note is our
shows the semitone/partial value relative to the Oscillator 1 pitch.
DISPLAY
I I I I S S S S P P P P L L L L A A A A Y Y Y Y
in the Oscillator section is used to display information pertaining to the frequency/
N . function is activated the LED D
O
7. Panel reference: Oscillator 2
page 111), you might reach frequencies that aren't au-
1-5 1-5 1-5 1-5
ARTIAL
OARSE
1-5 1-5
1-5 1-5
switches to show partials instead of
ISPLAY
-
AR
N . and KBT H
O OFF Z
knob the pitch and LED
Page 67