Champion Power Equipment 200946 Operator's Manual
  1. Manuals
  2. Brands
  3. Champion Power Equipment Manuals
  4. Paper Shredder
  5. 200946
  6. Operator's manual
Champion Power Equipment 200946 Operator's Manual

Champion Power Equipment 200946 Operator's Manual

3 in. (7.6 cm) chipper shredder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATOR'S MANUAL
MODEL #200946
3 IN. (7.6 CM) CHIPPER SHREDDER
ACTIVATE YOUR WARRANTY
SERIAL NO.
by registering your product:
championpowerequipment.com
or visit championpowerequipment.com
READ AND SAVE THIS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product. Failure to
do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
REV 20240116
Champion Power Equipment, Inc.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 200946 and is the answer not in the manual?

Questions and answers

Related Manuals for Champion Power Equipment 200946

Summary of Contents for Champion Power Equipment 200946

  • Page 1 This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice. REV 20240116 Champion Power Equipment, Inc.

  • Page 2: Table Of Contents

    200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER TABLE OF CONTENTS TABLE OF CONTENTS Maintenance ..........Engine Maintenance ..........Introduction ...........

  • Page 3: Introduction

    INTRODUCTION 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER INTRODUCTION SAFETY DEFINITIONS Congratulations on your purchase of a Champion Power Equipment The purpose of safety symbols is to attract your attention to (CPE) product. CPE designs, builds, and supports all of our possible dangers.

  • Page 4: Important Safety Instructions

    200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS  WARNING Operation of this equipment may create sparks that can start  DANGER fires around dry vegetation. Engine exhaust contains carbon monoxide, a colorless, A spark arrestor may be required. The operator should contact odorless, poison gas.

  • Page 5: Fuel Safety

    IMPORTANT SAFETY INSTRUCTIONS 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER Fuel Safety  WARNING Operator Work Zone Area  DANGER Keep work zone clear of debris while working to ensure safe GASOLINE AND GASOLINE VAPORS ARE HIGHLY footing. FLAMMABLE AND EXPLOSIVE.

  • Page 6: Training

    IMPORTANT SAFETY INSTRUCTIONS 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER When operating the chipper-shredder:  WARNING – DO NOT move or tip the chipper-shredder during operation. Although the chipper shredder contains a spark arrester, – DO NOT tip the chipper-shredder or allow fuel or oil to spill.

  • Page 7: Operation

    200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER IMPORTANT SAFETY INSTRUCTIONS 5. Check to make sure the chipper-shredder is on a level – If a major clog occurs; turn the fuel valve off and let the surface that is not asphalt, concrete or harden ground. Block...

  • Page 8: Safety And Dataplate Labels

    IMPORTANT SAFETY INSTRUCTIONS 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER Safety and Dataplate Labels These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement.
  • Page 9 IMPORTANT SAFETY INSTRUCTIONS 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER LABEL DESCRIPTION DANGER PELIGRO DANGER Danger icon - discharge WARNING CLEAN-OUT ACCESS PANEL - Do not operate without panel in place. ADVERTENCIA Warning - Clean-out access PANEL DE ACCESO DE LIMPIEZA - No opere sin el panel en su lugar.

  • Page 10: Safety Symbols

    IMPORTANT SAFETY INSTRUCTIONS 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product.
  • Page 11 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER IMPORTANT SAFETY INSTRUCTIONS SYMBOL MEANING Amputation Hazard. Contact with rotating blades will cause serious injury. Keep hands out of openings while machine is running. Toxic Fumes. The engine exhaust from this product contains chemicals known to the state of California to cause cancer and birth defects and other reproductive harm.

  • Page 12: Operation Symbols

    200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER IMPORTANT SAFETY INSTRUCTIONS Operation Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product.

  • Page 13: Controls And Features

    CONTROLS AND FEATURES 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER CONTROLS AND FEATURES Read this operator’s manual before operating your chipper-shredder. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference.

  • Page 14: Parts Included

    200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER CONTROLS AND FEATURES Parts Included Hardware Part Part Qty. Hardware Needed Tool Needed Qty. Chipper Chute Lock Nut M10, Flange 1× 15mm wrench or socket Flange Bolt M8 × 20 1× 12mm wrench or socket...

  • Page 15: Assembly

    ASSEMBLY 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER ASSEMBLY Your chipper-shredder requires some assembly. This unit ships from our factory without oil. It must be properly serviced with fuel and oil before operation. If you have any questions regarding the assembly of your chipper- shredder, call our Technical Support Team at 1-877-338-0999.

  • Page 16: Collection Bag

    ASSEMBLY 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER Add Engine Oil 3. Thread the M6 lock nut onto the threaded stud to secure the chute deflector to the discharge chute.  WARNING 4. From both sides, insert a knob bolt through the slotted hole on the chute deflector and into the threaded hole on the...

  • Page 17: Add Fuel

    200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER ASSEMBLY 4. Check engine oil level before every use and add as needed. Add Fuel  DANGER Gasoline vapors are highly flammable and extremely explosive. OIL DIP STICK DO NOT light or smoke cigarettes. Fire or explosion can cause severe burns or death.

  • Page 18: Operation

    OPERATION 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER OPERATION  CAUTION Use regular unleaded gasoline with a minimum octane rating Chipper-Shredder Location of 87 and an ethanol content of less than 10% by volume. Never operate the chipper-shredder indoors or inside any confined DO NOT light cigarettes or smoke when filling the tank.

  • Page 19: Before Each Use Inspect The Chipper-Shredder

    OPERATION 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER  WARNING DO NOT operate a damaged chipper-shredder, or one with damaged or loose parts. Operating a damaged unit or one with Up to Up to loose parts may cause damage to the product or injury to the 75 ft.

  • Page 20: Chipper-Shredder Operation

    OPERATION 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER Chipper-Shredder Operation 5. Pull the starter cord slowly until resistance is felt and then pull rapidly.  DANGER This machine has rotating blades and parts capable of amputating body parts. This machine can also throw objects at high velocity and long distances.

  • Page 21: Chipping And Shredding Tips

    200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER OPERATION   WARNING WARNING ALWAYS use the chipper-shredder for its intended uses only. Never insert pieces larger than 3 in. (7.6 cm) in diameter as The chipper-shredder should only be used to chip branches 3 this may cause damage or injury.

  • Page 22: Stopping The Engine

    200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER OPERATION 4. Using your hands, remove the material that is still atop the 3. Push the engine switch to the “OFF” position. shredding chute. DO NOT stick your hands in the shredder hopper, only remove the material on top.

  • Page 23: Maintenance

    MAINTENANCE 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER The owner/operator is responsible for all periodic maintenance. Engine Model: R224P Complete all scheduled maintenance in a timely manner. Carb. Code High Alt. Jet Part Number Min. Altitude Correct any issue before operating the chipper shredder.

  • Page 24: Chipper-Shredder Maintenance

    200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER MAINTENANCE Cleaning and Adjusting the Spark Plug(s) Cleaning the Chipper-shredder 1. Remove the spark plug cable from the spark plug.  CAUTION 2. Use a spark plug socket (not included) to remove the plug.

  • Page 25: Repair

    MAINTENANCE 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER Repair Shredder Blade and Flail Blade Inspection and Replacement  WARNING To avoid serious injury, perform maintenance on the unit only when the engine is stopped. Always disconnect the spark plug wire and fasten it away from the plug before beginning the maintenance, to prevent accidental starting of the engine.

  • Page 26: Maintenance Schedule

    MAINTENANCE 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER 5. Using a 3/16 in. hex wrench and a 12mm wrench, loosen CHIPPER KNIFE CUTTING EDGE the four (two on each blade) M8 × 25 countersink hex head screws (A) and M8 lock nuts (B) and remove the chipper...

  • Page 27: Storage

    200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER STORAGE Engine Stored for Less than 30 Days EVERY 50 HOURS OR PER 6 MONTHS 1. Add a properly formulated fuel stabilizer to the tank. — Clean and adjust spark plug —...

  • Page 28: Specifications

    SPECIFICATIONS 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER SPECIFICATIONS Spark Plug Specifications OEM Type ............ . F6RTC Chipper-shredder Specifications Replacement Type ...... NGK BPR6ES or equivalent Gap (R224P) ..

  • Page 29: Troubleshooting

    TROUBLESHOOTING 200946 - 3 IN. (7.6 CM) CHIPPER SHREDDER TROUBLESHOOTING Problem Cause Solution No fuel. Add fuel. Engine will not start. Faulty spark plug. Replace spark plug. Unit loaded during start up. Remove load from unit. Fill crankcase to the proper level.

  • Page 30: Warranty

    Limits of Implied Warranty and Consequential Damage Repair/Replacement Warranty Champion Power Equipment disclaims any obligation to cover CPE warrants to the original purchaser that the mechanical and any loss of time, use of this product, freight, or any incidental electrical components will be free of defects in material and or consequential claim by anyone from using this product.

  • Page 31: Your Warranty Rights And Obligations

    AND THE UNITED STATES ENVIRONMENTAL PROTECTION AGENCY (U.S. EPA) EMISSION CONTROL SYSTEM WARRANTY Your Champion Power Equipment (CPE) engine complies with U.S. EPA emissions regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The US EPA and CPE are pleased to explain the Federal Emission Control Systems Warranty on your 2024 small off-road engine (SORE) and engine powered equipment.

  • Page 32: Emission Control System Warranty

    EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1997 and later model year small off-road engines (SORE). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.

  • Page 33: To Obtain Warranty Service

    You must take your CPE engine or the product on which it is installed, along with your warranty registration card or other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours.

Table of Contents