Champion Power Equipment 100472 Operator's Manual
  1. Manuals
  2. Brands
  3. Champion Power Equipment Manuals
  4. Paper Shredder
  5. 100472
  6. Operator's manual

Champion Power Equipment 100472 Operator's Manual

3 in. 7.6 cm chipper shredder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATOR'S MANUAL
MODEL #100472
3 iN. (7.6 cM) chiPPER ShREDDER
REGISTER YOUR PRODUCT ONLINE
at championpowerequipment.com
or visit championpowerequipment.com
READ AND SAVE ThiS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product. Failure to
do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
Made in China - REV 20200507
Champion Power Equipment, Inc., Santa Fe Springs, CA USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 100472 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Champion Power Equipment 100472

Summary of Contents for Champion Power Equipment 100472

  • Page 1 This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice. Made in China - REV 20200507 Champion Power Equipment, Inc., Santa Fe Springs, CA USA...

  • Page 2: Table Of Contents

    TAbLE Of cONTENTS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER TAbLE Of cONTENTS Maintenance ..........Engine Maintenance ..........introduction ........... Chipper-Shredder Maintenance .........

  • Page 3: Introduction

    100472 - 3 iN. (7.6 cM) chiPPER ShREDDER iNTRODUcTiON SAfETY DEfiNiTiONS Congratulations on your purchase of a Champion Power Equipment The purpose of safety symbols is to attract your attention to (CPE) product. CPE designs, builds, and supports all of our possible dangers.

  • Page 4: Important Safety Instructions

    SAfETY iNSTRUcTiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS WARNiNG  Operation of this equipment may create sparks that can start DANGER  fires around dry vegetation. Engine exhaust contains carbon monoxide, a colorless, A spark arrestor may be required. The operator should contact odorless, poison gas.

  • Page 5: Fuel Safety

    SAfETY iNSTRUcTiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER fuel Safety WARNiNG  Keep Operator Work Zone Clear DANGER  Keep work zone clear of debris while working to ensure safe GaSOLINE aND GaSOLINE VaPORS aRE hIGhLY footing.

  • Page 6: Training

    SAfETY iNSTRUcTiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER When operating the chipper-shredder: WARNiNG  – DO NOT move or tip the chipper-shredder during operation. Although the chipper shredder contains a spark arrester, – DO NOT tip the chipper-shredder or allow fuel or oil to spill.

  • Page 7: Operation

    SAfETY iNSTRUcTiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER 5. Check to make sure the chipper-shredder is on a level – If a major clog occurs; turn the fuel valve off and let the surface that is not asphalt, concrete or harden ground. Block...

  • Page 8: Safety And Dataplate Labels

    Indice d’octane minimal de 87. Maximum 10 % d'éthanol. This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for outside parties without the explicit consent of Champion Power Equipment.
  • Page 9 AVERTISSEMENT on white substrate. This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for NETTOYER PANNEAU D'ACCÈS - ne pas outside parties without the explicit consent of Champion Power Equipment.

  • Page 10: Safety Symbols

    SAfETY iNSTRUcTiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product.
  • Page 11 SAfETY iNSTRUcTiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER SYmBOL mEaNING amputation hazard. Contact with rotating blades will cause serious injury. Keep hands out of openings while machine is running. Toxic Fumes. The engine exhaust from this product contains chemicals known to the state of California to cause cancer and birth defects and other reproductive harm.

  • Page 12: Operation Symbols

    1. Check oil level. Recommended oil is 10W-30. This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for outside parties without the explicit consent of Champion Power Equipment.

  • Page 13: Controls And Features

    AND fEATURES 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER cONTROLS AND fEATURES Read this operator’s manual before operating your chipper-shredder. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference.

  • Page 14: Parts Included

    AND fEATURES 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER Parts included hardware Part Part Qty. hardware Needed Tool Needed Qty. Wheel Cap Wheels Flange Bolt M8 × 12 1× 12mm wrench or socket Flat Washer Ø15 Chipper Chute Lock Nut M8, Flange 1×...

  • Page 15: Assembly

    ASSEMbLY 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER ASSEMbLY Your chipper-shredder requires some assembly. This unit ships from our factory without oil. It must be properly serviced with fuel and oil before operation. If you have any questions regarding the assembly of your chipper- shredder, call our Technical Support Team at 1-877-338-0999.

  • Page 16: Install The Handle

    ASSEMbLY 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER 3. Insert four M6 x 15mm flange bolts through the four holes of after operation, or before storage. The collection bag will collect the impeller housing and into the weld nuts in the shredder up to 2 bushels (70 L) of material.

  • Page 17: Add Fuel

    ASSEMbLY 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER Add fuel NOTicE  1. Use clean, fresh, regular unleaded gasoline with a minimum Once oil has been added, a visual check should show oil about octane rating of 87 and an ethanol content of less than 10% 1-2 threads from running out of the fill hole.

  • Page 18: Operation

    OPERATiON 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER NOTicE WARNiNG   Our engines work well with 10% or less ethanol blend During operation the muffler and exhaust fumes produced will gasoline. When using ethanol-gasoline blends there are some become hot.

  • Page 19: Before Each Use Inspect The Chipper-Shredder

    OPERATiON 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER before Each Use inspect the chipper- 3. Move the choke lever to the “CHOKE” position. Shredder 1. Always make sure the spark plug wire has been disconnected and engine has been grounded.

  • Page 20: Chipper-Shredder Operation

    OPERATiON 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER 6. Make sure the materials that are going to be chipped or NOTicE  shredded are free of any rocks, trash, metals and other foreign objects. Keep choke lever in “CHOKE” position for only 1 pull of the recoil starter.

  • Page 21: Chipping And Shredding Tips

    OPERATiON 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER chipping and Shredding Tips NOTicE  Chipping After all material has been processed it is recommended that 1. Make sure wood is less than 3 in. (7.6 cm) in diameter. the unit run for short period of time to clear out any left over material that may still be in the chutes or flail housing.

  • Page 22: Operation At High Altitude

    MAiNTENANcE 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER 1. Move the fuel valve to the “OFF” position. To alleviate high altitude issues other than the natural power loss, CPE can provide a high altitude carburetor main jet. The alternative main jet and installation instructions can be obtained by contacting our Technical Support Team.

  • Page 23: Engine Maintenance

    MAiNTENANcE 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER The owner/operator is responsible for all periodic maintenance. Cleaning and adjusting the Spark Plug(s) Complete all scheduled maintenance in a timely manner. 1. Remove the spark plug cable from the spark plug.

  • Page 24: Cleaning The Chipper-Shredder

    MAiNTENANcE 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER cleaning the chipper-shredder Repair Shredder Blade and Flail Blade Inspection and Replacement cAUTiON  WARNiNG  DO NOT spray engine with water. To avoid serious injury, perform maintenance on the unit only Water can contaminate the fuel system and can enter the when the engine is stopped.
  • Page 25 MAiNTENANcE 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER CHIPPER KNIFE CUTTING EDGE Top View Side View 1/16" MIN. 30° To inspect, sharpen, or replace the chipping knives: 1. Turn the engine off and wait for all moving parts to stop.

  • Page 26: Maintenance Schedule

    STORAGE 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER 5. Using a 3/16 in. hex wrench and a 12mm wrench, loosen EVERY 50 hOURS OR PER 6 mONThS the four (two on each blade) M8 x 25 countersink hex head —...

  • Page 27: Engines Stored For Over 30 Days

    STORAGE 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER 4. Let the engine run until fuel starvation has stopped the engine. 5. Let the engine completely cool before cleaning and storage. 6. Clean the engine according to the maintenance section.

  • Page 28: Specifications

    SPEcificATiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER SPEcificATiONS Spark Plug Specifications OEM Type ..........NHSP F6RTC chipper-shredder Specifications Replacement Type ...... NGK BPR6ES or equivalent Max Diameter Chipper Material .

  • Page 29: Parts Diagram

    SPEcificATiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER Parts Diagram...

  • Page 30: Parts List

    SPEcificATiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER Parts List Part Number Description Qty. Part Number Description Qty. 31 1.93.08 Lock Washer, Ø8 27.304 Engine, 224cc Impeller Assembly, 602.300601.01 Engine Plate Assembly 32 602.303100.00.2 Black 2.14.002 Flat Key, 6.3 x 6.3 x 50 33 602.303004.00...

  • Page 31: Engine Parts Diagram

    SPEcificATiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER Engine Parts Diagram...

  • Page 32: Engine Parts List

    SPEcificATiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER Engine Parts List Part Number Description Qty. Part Number Description Qty. 37 27.050100.03 Crankshaft 1.16674.0608 Flange Bolt M6 x 8 38 1.276.6205 Bearing 6205 Cover,Recoil Starter, 27.061100.02.2 Black Gasket, Crankcase 39 24.030008.00 Cover 21.061005.00...
  • Page 33 SPEcificATiONS 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER Part Number Description Qty. Part Number Description Qty. 117 27.210003.00 Retainer, Exhaust Valve Wire Sheath 76 21.040007.00 Spring 118 24.070100.04 Cap, Fuel Tank Retainer, Intake Valve 119 46.070300.00 Fuel Filter, Fuel Tank 77 21.040001.00...

  • Page 34: Troubleshooting

    TROUbLEShOOTiNG 100472 - 3 iN. (7.6 cM) chiPPER ShREDDER TROUbLEShOOTiNG Problem Cause Solution No fuel. Add fuel. Engine will not start. Faulty spark plug. Replace spark plug. Unit loaded during start up. Remove load from unit. Fill crankcase to the proper level.
  • Page 35 Limits of Implied Warranty and Consequential Damage Repair/Replacement Warranty Champion Power Equipment disclaims any obligation to cover CPE warrants to the original purchaser that the mechanical and any loss of time, use of this product, freight, or any incidental electrical components will be free of defects in material and or consequential claim by anyone from using this product.
  • Page 36 AND THE UNITED STATES ENVIRONMENT PROTECTION AGENCY (U.S. EPA) EMISSION CONTROL SYSTEM WARRANTY Your Champion Power Equipment (CPE) engine complies with U.S. EPA emission regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The US EPA AND CPE are pleased to explain the Federal Emission Control Systems Warranty on your 2020 small off-road engine (SORE) and engine powered equipment.
  • Page 37 EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1997 and later model year small off-road engines (SORE). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.
  • Page 38 You must take your CPE engine or the product on which it is installed, along with your warranty registration card or other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours.

Table of Contents