Subscribe to Our Youtube Channel
Related Manuals for zapco ADSP-IV Series
Summary of Contents for zapco ADSP-IV Series
- Page 1 ADSP-IV SERIES Owner’s Manual Before operating the unit, please read this manual throughly and retain it for future reference. Any updates are available on zapco.com/download...
-
Page 2: Table Of Contents
Table of Contents General instructions IT Istruzioni Generali DE Allgemeine Anweisungen FR Instructions Générales ES Instrucciones Generales CH 常规安装指引 The new Zapco ADSP-IV Series DSP/Amp Panels Remote Control The Microphone The Graphical User Interface The Main Screen The Advanced Menu... -
Page 3: General Instructions
• La borne entre l'alimentation principale (+12V B) et la Zündeingang +12 (REM) und kann an die accessorio (ACC) masse (GND) est l'entrée de mise sous tension +12 (REM) Mounting your Zapco amplifier is easy. Just keep in mind a Zündausgangsleitung des Hauptgeräts angeschlossen few guidelines: Installare l’amplificatore werden. -
Page 4: Instrucciones Generales
DSP for the car and included a full line of amplifiers with full function digital processing • Utilice siempre pasacables cuando pase el cable a través 油门和离合 踏板等, 以避免电线被夹 build right in. In 2016 we brought out our fourth generation of processing in the Zapco del cortafuegos o cualquier otro panel metálico 电源连接的准备工作... - Page 5 DSP-Z8 IV AT Panels ADSP-Z8 IV-6AT Panels DSP-Z8IV AT 1. Comm Port for HD-BT module 8. Microphone Input for Auto-Tuning 1. Power-On LED 8. Coaxial digital input 2. Coaxial digital input 9. Dash remote port 2. Auto-on switch for OEM integration 9.
- Page 6 ADSP-Z12 IV-10A Panels ADSP-Z16 IV-12A Panels 1. Coaxial digital input 9. Power LED 1. Coaxial digital input 9. Power-On LED 2. Speaker level input plug for OEM 10. USB connector for PC control 2. Speaker level input plug for OEM 10.
-
Page 7: Remote Control
Remote Control The Microphone (optional for DSP-Z8 IV AT and ADSP-Z8 IV-6AT) The M-AT1 is a special microphone for setting up the sound automatically, based on the response characteristics of the speakers and auto detail detection of the car. After detecting all the necessary information, the audio information screen will be transmitted to the computer. -
Page 8: The Graphical User Interface
3. This section is the quick setup area and will be the go-to setup for most systems. Across Just download the file from the Zapco website an put it on your desktop (the number the bottom you find 2CH, 4CH, 6CH, 8CH, and SUM. All digital inputs are 2CH inputs and following “rc”... -
Page 9: The Advanced Menu
c. The Phase column lets you adjust the polarity of each channel, so you have all The Advanced Menu speakers moving the same direction at the same time. See Pag. 22 for more information on Phase. If you have the M-AT1 calibration mic, the autotuning system The Advanced menu of the DSP-IV AT processor GUI, can take you to the Mixing Set where will check the phase of all the speakers for you. - Page 10 Auto Calibration. When used with the optional M-AT1 microphone, the GUI can 5. The Tips area will display messages or reminders i.e. To make sure your crossovers are automatically calibrate the major tuning functions of equalization, signal delay, and phase. set before the calibration run (to protect the tweeters).
-
Page 11: The File Menu
The File Menu Read from Device works the same way. You will get the Read from Device menu and at the bottom you can Select Read Place, choosing any of the saved memory positions, and then click Read to load the settings of that memory preset into the DSP. Delete from Saving your work is critical. -
Page 12: Manual Tuning
B. Midrange and Woofer/Mid-Bass: Now mute all but the midrange. These are easier Now you have set the R-to-L phase of each pair of speakers and you have blended each because phase is more obvious at lower frequencies and because you can use more volume. pair into the system in the correct phase for the best sound stage. - Page 13 The Tuning Tools of the GUI 5. EQ: This is the EQ band box. You can which of the 31 EQ bands you will adjust by clicking on any of the green band buttons and using drag-n-drop, but you can also click You will use the EQ graph and the Function bar above for making the EQ adjustments.
- Page 14 What We Want to Achieve Best Response Curve You will use the EQ graph and the Function bar above for making the EQ adjustments. Below we lay out the EQ tuning functions. Of course, there is no way to know what the response in any particular car will be.
-
Page 15: Technical Specifications
A Bad Response Curve Technical Specifications At the bottom line the sound you want from your car will be subject to your tastes. DSP-Z8 IV AT DSP-Z16 IV Everyone will like the “Best Response Curve” and everyone will like the “Good Response Curve”. - Page 16 Max 515 cm, Step 0.68 cm Max 515 cm, Step 0.68 cm may cause permanent hearing loss. Polarity 0-180° Polarity 0-180° Polarity 0-180° ZAPCO strongly advises that you use common sense when setting Mute/Solo Yes, each channel Yes, each channel Mute/Solo Yes, each channel volume levels.
- Page 17 Modesto, California USA Since 1974 zapco.com...
Need help?
Do you have a question about the ADSP-IV Series and is the answer not in the manual?
Questions and answers