Related Manuals for Knuth V-Turn 410 PRO
Summary of Contents for Knuth V-Turn 410 PRO
- Page 1 Machine Tools OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS V-Turn 410 - 2.0 Part No 300822 For the important safety of your body, please read this manual book and understand its contents before operation.
-
Page 2: Safety Instruction
Machine Tools OPERATING INSTRUCTIONS 1 Safety instruction Operation manual For your own security read the operation manual before starting the machine. The operation manual should be kept in a secure place. You should know about how to handle the machine, it’s limits and it’s specific dangers. Keep your working place clean Disorder on your working place will result in danger. - Page 3 Machine Tools OPERATING INSTRUCTIONS Unplug the machine If you don’t use and while servicing the machine pull off the power supply plug. This is necessary because the machine should not run unintentionally and to protect you from electric shock. Beware of unintentional run Confirm that the main power switch is off while you plug in the power supply plug.
-
Page 4: Table Of Contents
Machine Tools OPERATING INSTRUCTIONS CONTENTS 1. General Safety Rules for Power Tools 2. Specification 3. Lifting 4. Cleaning 5. Installing 6. Lathe Alignment Part.1 7. Lathe Alignment Part.2 8. Slide Ways Attention 9. Cross-Slide Nut 10. Electrical Controls 11. Apron Auto-feed 12. -
Page 5: General Safety Rules For Power Tools
Machine Tools OPERATING INSTRUCTIONS 1. General Safety Rules for Power Tools Warning: Do not attempt to operate until you have read thoroughly and understand completely all instructions, rules etc. Contained in this manual failure to comply can result in accidents involving fire, electric shock, or serious personal injury. Maintain owners’... -
Page 6: Specification
Machine Tools OPERATING INSTRUCTIONS 2. Specification Capacity Swing Over Bed φ410mm(16") Swing Over Cross Slide φ255mm(10") Swing In Gap Diameter×Width ") φ580(22")×190(7 Height of Center 205mm(8") Distance Between Centers 1000mm(40") 1500mm(60") Width of Bed 250mm(10") Cutting Tool Max Section 20×20mm(3/4"×3/4") Total Travel of Cross Slide 210mm(8 ") -
Page 7: Lifting
Machine Tools OPERATING INSTRUCTIONS 3. Lifting Use a sling-chain to sling the lathe as in fig position the saddle and tailstock along the bed to obtain balance. Important: The sling-chain should not touch the leadscrew or Feed-shaft to avoid damage. Unloading of the machine. - Page 8 Machine Tools OPERATING INSTRUCTIONS ensure continued lathe accuracy. Fixed installation: Position lathe over six bolts (1/2 in. or 12mm.dia.) set into the foundation to correspond with holes in the mounting feet; Accurately level the machine, then tighten hold-down bolts, Re-check bed level.
- Page 9 Machine Tools OPERATING INSTRUCTIONS...
-
Page 10: Lathe Alignment Part.1
Machine Tools OPERATING INSTRUCTIONS Construction of the Ground Due to the recent tendency of utilizing Ultra-Hard Alloy Steel tools, it surely increases the speed of heavy cutting comparing to the previous steel tool. But, in the mean time, it easily happens to the vibration of the machine. For assuring better cutting result, it requires a very strong and steady construction of ground. -
Page 11: Lathe Alignment Part.2
Machine Tools OPERATING INSTRUCTIONS The Importance and Methods of Spindle Leveling Adjustment 1. Switch on to make the Spindle turn while the Spindle is set up at 1170r.p.m. By putting the palm of the left hand on the Headstock cover to fell its chatter. An unrevealing Spindle will lead to lathe chatter. -
Page 12: Slide Ways Attention
Machine Tools OPERATING INSTRUCTIONS 8. Slide Ways Attention Tapered gib strips are fitted to slideways of saddle cross-slide and top (compound) slides so that any slackness, which may develop can be rectified. Ensure that slideways are thoroughly cleaned and lubricated before attempting adjustment. -
Page 13: Electrical Controls
Machine Tools OPERATING INSTRUCTIONS 10. Electrical Controls The power switch is fitted on the side of electrical box in back of the bed and below the headstock. Except the main switch, all electrical controls are fitted in the front of the headstock. 1. - Page 14 Machine Tools OPERATING INSTRUCTIONS...
-
Page 15: Speed Controls
Machine Tools OPERATING INSTRUCTIONS 11. A Speed Controls Spindle speeds: While the electrical switch set at "l” position, the lever on the headstock rotated left-hand side, it provides speeds from 30~550r.p.m, and rotated to right-hand side, to provides speeds from 550~3000r.p.m. Then rotate the selecting switch to arrow aligned “H”... -
Page 16: Chucks And Chucks Mounting
Machine Tools OPERATING INSTRUCTIONS 13. Chucks and Chucks Mounting When fitting chucks or faceplates, first ensure that spindle and chuck tapers are scrupulously clean and that all cams lock in the correct positions; see Fig.12. it may be necessary to re-set the cam lock studs (A) when mounting a new chuck. To do this, remove the cap-head locking screws (B) and set each stud so that the scribed ring (C) is flush with the rear face of the chuck-with the slot lining up with the locking screw hole. - Page 17 Machine Tools OPERATING INSTRUCTIONS ubrication diagram Pos. 1 Pos. 3 Pos.4 Pos.5 Pos. 2 Fig. 1: Lubrication schedule with operating hours Please check the oil level of the main gears daily! Check the oil level at the inspection glasses. Pos. Machine filling operation...
- Page 18 OPERATING INSTRUCTIONS Recommended lubrications The lubricants recommended here have been tested at the Knuth facilities and proven suitable. Please use only lubricants which are listed in this operating manual. Nevertheless, it is possible to use other brands with the same characteristics.
- Page 19 Machine Tools OPERATING INSTRUCTIONS...
Need help?
Do you have a question about the V-Turn 410 PRO and is the answer not in the manual?
Questions and answers