Cookology GH606SS User Manual
  1. Manuals
  2. Brands
  3. Cookology Manuals
  4. Hob
  5. GH606SS
  6. User manual

Cookology GH606SS User Manual

Hide thumbs

Advertisement

Table of Contents

NOTE
:
This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep
it in a safe place so that it is easily available for future
reference; for you or any person not familiar with the operation
of the appliance.
THIS APPLIANCE MUST BE INSTALLED BY A GAS SAFE ENGINEER.
Address: The Wright Buy Ltd Unit 2 Piperell Way, Haverhill, Suffolk, CB9 8QW,
United Kingdom
Please register the warranty for this product on www.cookology.com
User manual for you
Built-in Gas Hob
Model
GH306SS
GH309SS
GH601SS
GH700SS
GGH700BK
GGH705BK
GH705SS
GGH301BK
GGH306BK
GH606SS
GGH606BK
GGH906BK
GH906SS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GH606SS and is the answer not in the manual?

Questions and answers

Related Manuals for Cookology GH606SS

Summary of Contents for Cookology GH606SS

  • Page 1 THIS APPLIANCE MUST BE INSTALLED BY A GAS SAFE ENGINEER. Address: The Wright Buy Ltd Unit 2 Piperell Way, Haverhill, Suffolk, CB9 8QW, United Kingdom Please register the warranty for this product on www.cookology.com...

  • Page 2: Environmental Note

    Environmental note o The packaging materials that uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.

  • Page 3: Important Safety Information

    Important safety information General Information o IMPORTANT: The adjacent furniture and all materials used in the installation must be able to withstand a minimum temperature of 85°C above the ambient temperature of the room it is located in, whilst in use. o Certain types of vinyl or laminate kitchen furniture are particularly prone to heat damage or discolouration at temperatures below the guidelines given above.
  • Page 4 o Make sure that all of the cooking zones are switched off after use. Cleaning o Cleaning of the hob should be carried out on a regular basis. o IMPORTANT: Before attempting to clean the appliance, it should be disconnected from the mains and cool. o Great care should be taken whilst using this appliance and when following the cleaning procedure.

  • Page 5: Specifications

    Specifications GH306SS / GH309SS / GGH306BK Product specifications: A = 1 x 3.00 KW rapid burner B = 1 x 1.00 kW auxiliary burner C = Control panel o Front control operation o Automatic ignition o Heavy duty cast iron pan stands o Flame failure safety device on each burner Standard accessories: o LPG conversion jets...
  • Page 6 GH601SS/GH606SS Product specifications: A = 1 x 3.00 kW rapid burner B = 2 x 1.75 KW semi-rapid burners C = 1 x 1.00 kW auxiliary burner D = Control panel o Front control operation o Automatic ignition o Heavy duty cast iron pan stands...
  • Page 7 GH700SS Product specifications: A = 1 x 3.50 kW Wok burner B = 1 x 3.00 KW rapid burner C = 2 x 1.75 KW semi-rapid burners D = 1 x 1.00 kW auxiliary burner E = Control panel o Front control operation o Automatic ignition o Heavy duty cast iron pan stands o Flame failure safety device on each burner...
  • Page 8 GGH700BK / GGH705BK / GH705SS Product specifications: A = 1 x 3.50 kW Wok burner B = 1 x 3.00 KW rapid burner C = 2 x 1.75 KW semi-rapid burners D = 1 x 1.00 kW auxiliary burner E = Control panel o Front control operation o Automatic ignition o Heavy duty cast iron pan stands...
  • Page 9 GGH301BK Product specifications: A = 1 x 3.50 kW WOK burner B = Control panel o Front control operation o Automatic ignition o cast iron pan stands o Flame failure safety device on each burner Standard accessories: o LPG conversion jets...
  • Page 10 GGH606BK Product specifications: A = 1 x 3.50 kW rapid burner B = 2 x 1.75 KW semi-rapid burners C = 1 x 1.00 kW auxiliary burner D = Control panel o Front control operation o Automatic ignition o Heavy duty cast iron pan stands o Flame failure safety device on each burner Standard accessories: o LPG conversion jets...
  • Page 11 GGH906BK/GH906SS Product specifications: A = 1 x 3.50 kW Wok burner B = 1 x 3.00 KW rapid burner C = 2 x 1.75 KW semi-rapid burners D = 1 x 1.00 kW auxiliary burner E = Control panel o Front control operation o Automatic ignition o Heavy duty cast iron pan stands o Flame failure safety device on each burner...
  • Page 12 Electrical details Rated Voltage: 220 - 240 Vac 50 / 60 Hz Supply Connection: 3A (double pole switched fused outlet with 3mm contact gap) Max Rated Inputs: 0.0008 kW Mains Supply Lead: 3 core x 0.75mm (Type VV-F <HAR> marked) Gas details Rp ½...
  • Page 13 Automatic ignition with flame failure safety device The appliance is fitted with a flame failure safety device on each burner, which is designed to stop the flow of gas to the burner head in the event of the flame going out. To ignite a burner: o Press in the control knob of the burner that you wish to light and turn it anti-clockwise to the maximum position.
  • Page 14 Cleaning Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains supply before commencing cleaning process. Cleaning the hob top Any residues that are left on the hob top surface from cleaning agents will damage it.

  • Page 15: Installation

    o Remove the hob burners by pulling them upwards and away from the hob top. o Soak them for about ten minutes in hot water and a little detergent. o After cleaning and washing them, wipe and dry them carefully. o Before placing the burners back on the hob top, make sure that the gas jet is not blocked.
  • Page 16 o Building Standards (Issued by the Scottish Development Department) o IEE Wiring Regulations o Electricity at Work Regulations BS 6172 o Installation of Domestic Gas Cooking Appliances (if necessary, BS 5482 Installation of Domestic LPG Appliances) o BS 5440 Installation of Flues and Ventilation for Gas Appliances Positioning The adjacent furniture must be able to withstand a...
  • Page 17 This appliance is classified as Class 3 and therefore is to be built into a kitchen unit (depending on size) or 600mm worktop, providing the following minimum distances are allowed: o The edges of the hob must be a minimum distance of 55 mm from a side or rear wall.
  • Page 18 o The protective covering must be removed from both sides. o Do not leave a gap in the sealing agent or overlap the thickness. o IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture. This will make it difficult to remove the hob from the aperture in future if it needs to be serviced.
  • Page 19 Important information o This hob is supplied to run on natural gas only and cannot be used on any other type of gas without modification. o Conversion for use on LPG and other gases must only be undertaken by a qualified person. For information on the use of other gases, please contact the Advice Line.

  • Page 20: Gas Safety (Installation And Use) Regulations

    o Prolonged intensive use of the appliance may call for additional ventilation, either by the opening of a window, or by increasing the level of the mechanical ventilation device (where present). o This hob is not fitted with a device for discharging the products of combustion.
  • Page 21 Gas supply replacement and installation guidelines: Applicable to NG gas source and LPG gas Applicable to LPG gas source scenarios source scenarios that require pipeline that require hose connection connection seal seal The gas inlet The gas inlet pipe assembly pipe assembly Ø11.5 Female coupler R1/2"Female coupler...
  • Page 22 Gas connection The gas connection must be located in position where the stop tap is accessible. The end of the inlet connection point of the gas hob has a 1/2" thread that allows for: A fixed connection ■ Connection using a flexible pipe (L min. 1 m - max. 3 m) ■...
  • Page 23 GENERAL INJECTORS TABLE Power (in watts) Kind of gas Burners Nozzle Max. Min. mm/100 Natural 3500 1700 Rapid 3000 1500 1750 Semi-rapid 1000 Auxiliary L.P.G. 3500 1300 Butane Rapid 3000 1750 Propane Semi-rapid 1000 Auxiliary o Reassemble all the burners carefully; in particular you should make sure that the flame spreader is correctly placed on the burner.
  • Page 24 o Place a small bladed screwdriver on the screw to adjust the minimum flow (as shown in the image on the left). o Unscrew the adjusting screw, in order to increase the gas flow or tighten the adjusting screw to decrease the gas flow.
  • Page 25 If a gas tap becomes stiff to operate, then you should proceed as follows: o Remove the control knobs, pan supports, burners, hob fixing screws and clamps. o Remove the hob from the worktop and remove any underside protective covers. o Disconnect the fixings holding the tap to the fascia panel and separate the assembly.
  • Page 26 Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations Before connecting the appliance, make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. o Cable type: H05 VVF 3 core x 0.75 mm (Type VV-F <HAR>...

This manual is also suitable for:

Gh309ssGh601ssGh700ssGgh700bkGgh705bkGh705ss ... Show all

Table of Contents