SAFETY INSTRUCTIONS • Read the manual before use and keep it for future reference. • Do not use the device if any sharp edges appear. • In the event of a fault, stop the use immediately and contact service. Do not repair the scooter by yourself.
• Before reversing, make sure that there is no obstacle behind you. Reverse to the lowest speed. • Avoid sudden movements and sudden changes in direction. • Keep your hands and feet on the armrests. • If you are driving up a hill, do not reverse. •...
FRONT - CONTROL PANEL The control panel contains the following parts. Lock Speed setting Battery indicator Horn Front lights Control levers REAR PART Battery contacts Control cables Hooks Manual wheel control Seat holder...
BATTERY 3-pin charging port Overvoltage protection SEAT Seat Seat post Armrests Lever ASSEMBLY 1. Remove the packing material and pull all parts out of the box. 2. The handlebars must be raised and secured before use. a. Loosen the hand knob...
Page 7
b. Raise the handlebars to the desired angle so that you can reach them while driving. c. Tighten the hand knob. d. The required angle of the handlebars can be changed, just loosen the hand knob, adjust the angle and then tighten the knob again. WARNING: Always make sure the handlebars are properly tightened before use.
Page 8
4. Make sure that the seat is properly attached to the seat post 5. Insert the seat into the seat post at the rear of the scooter. 6. Adjust the height and place in the pin. Insert the pin through the holes in the seat post, it must be inserted along the entire length.
Page 9
8. Use the lever to release the seat and turn it so that it faces the front of the handlebars. Then use the lever to lock the seat in position. 9. Attach the right and left armrests to the sides of the seat. The armrests are secured with a hand knobs.
FRONT AND REAR CONNECTIONS The scooter is delivered connected; however, the front and rear can be detached for easier transportation or storage. 1. Switch the scooter to manual mode using the lever on the rear wheels. 2. Tilt the rear of the truck back until it rests on the anti-slip bars and handles on the back. Note: Make sure the seat post is parallel to the ground and the handles are in the up position.
Recharge the battery for 10 to 12 hours and then continue to use the scooter. After 4 to 5 charging cycles, the battery reaches its maximum capacity. If you do not use the scooter regularly, you need to charge the battery to the maximum once every two weeks.
Page 12
IGNITION AND KEY A key and ignition are required to operate the truck. Insert the key to turn it on. The power light turns on. If the scooter is not used, remove the key. WARNING: Do not remove the key as a way of stopping unless it is an emergency. Suddenly pulling out the key can damage the product.
Page 13
CONTROL LEVERS You can use the levers on the sides to change the direction of travel forwards - backwards. The harder you press the lever, the faster the movement will be up to the set maximum. As soon as you release the lever, the truck starts to decelerate until it stops.
WARNING: Never switch the scooter to manual mode unless you have the assistance of another person. Do not switch the scooter to manual mode on hills or inclines. Failure to follow these instructions may result in personal injury or property damage. DISASSEMBLY 1.
7. Lift the part where the two parts are connected and release them from the hooks. 8. To connect, follow the steps above in reverse order MAINTENANCE Avoid bumps or blows to the control panel and handlebars. Avoid exposure to extreme temperature conditions such as cold, heat or humidity. If the scooter is exposed to moisture, it must first be dried before use.
Page 16
Signal Cause Fault Solution Low battery Discharged battery Recharge the battery Tighten battery Poor battery contacts Loosen battery cables connection nut Cables were connected to opposite Replace control Wrong battery contacts 1x sound signal poles, short circuit unit control unit The black power cord Short circuit between is touching the motor...
The scooter is not in The charger has been manual mode and the Replace the brakes connected brake does not work Brake coil short Resistance is less than Replace the brakes 40 Ω circuited battery The voltage is higher connected in parallel Check the cables than 48 V and not in series...
Don’t put the batteries among house waste but hand them in to the recycling place. TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS General Conditions of Warranty and Definition of Terms All Warranty Conditions stated here under determine Warranty Coverage and Warranty Claim Procedure.
Page 20
Praha 5-Hlubočepy 150 00 IČ: 268 47 264 Czech Republic Declares on its own responsibility that product: IN 24911 Elektrický čtyřkolový vozík Baichen Omis Model W3431C is in agreement with the technical requirements for the product set by a government regulation...
Need help?
Do you have a question about the Baichen Omis and is the answer not in the manual?
Questions and answers