Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Biostar K8NBD-S9
Summary of Contents for Biostar K8NBD-S9
- Page 2 Important Safety Information...
-
Page 3: Table Of Contents
Table of the Contents Section 1 Introduction 1.1 Begin Your Tour In The DIY World ........ 1.2 Checking the Equipments ........... Section 2 Motherboard Set Up 2.1 Motherboard Features ..........2.2 Layout & Components ..........2.3 Central Processing Unit (CPU) ........ -
Page 4: Begin Your Tour In The Diy World
Begin Your Tour In The DIY World Checking the Equipments Software CD Mini PC System Driver CD Installation Guide Thermal Grease User’s Manual A Power Cord Screws Pack SATA/PATA power cable... -
Page 6: Motherboard Features
Supports AMD Athlon 64 FX processor. Caution: Supports AMD Athlon 64 processor. Please always install the DDR Module into DIMM1, or the sytem will not boot up. Supports AMD Sempron processor. AMD 64 architecture enables simultaneous 32 and 64 bit computing. - Page 7 Internal On-board Connectors and Headers 1 S/PDIF in connector 1 CD-in connector supports CD-ROM audio-in function. 1 MIC-in port. 1 floppy connector supports 2 FDD devices with 360K, 720K, 1.2M, 1.44M and 1 Line-out port 2.88Mbytes (optional). 2 USB 2.0 ports 2 IDE connectors support 4 IDE disk drives.
-
Page 8: Layout & Components
Layout & Components Central Processing Unit (CPU) Step 1 : Remove the socket protection cap. Step 2: Pull the lever sideways away from the socket and then raise the lever up to a 90-degree angle. Note: represents the 1st pin. -
Page 9: Fan Headers
DIMM matches the break on the Slot. Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU FAN power cable to the 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place JCFAN1. -
Page 10: Connectors, & Slots
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~5, Bus Master, and Ultra DMA 33/66/100/133 functionality. It has two HDD connectors IDE1 (primary) and IDE2 (secondary). The IDE connectors can connect a master and a slave drive, so you can connect up to four hard Pin opened Pin closed Pin1-2 closed disk drives. - Page 11 +5V(fused) +5V(fused) CD-ROM Audio-in Connector: JCDIN1 This connector allows user to connect the audio source from the variety devices, like CD-ROM, Caution: DVD-ROM, PCI sound card, PCI TV turner card etc.. To function FIO1,3,4 headers, they should be connected onto FIO1S1.
- Page 12 Pin 2-3 individually. Close CMOS Header: JCMOS1 By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and the CMOS data, please carefully follow the procedures to avoid damaging the motherboard.
-
Page 13: Overview
Overview Connecting Peripheral Devices RJ-45... - Page 14 To connect a monitor, plug the monitor cable into the VGA port located on the rear panel of your computer, or on the VGA card bracket.
-
Page 17: Installing Drives And Utilities
Installing Drives and Utilities... -
Page 18: Nvidia Raid
Windows XP home Edition Windows XP Professional Edition The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks up a large Windows 2000 Professiona file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the strip size parameter, which you set during the creation of the RAID set based on the system environment. - Page 19 Spanning (JBOD): Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1 array JBOD stands for “Just a Bunch of Disks”. Each drive is accessed as if it were on a standard system.
-
Page 21: System Does Not Start
5 . 1 5 . 3 System Does Not Start USB Device Problems 5 . 4 Software Problem 5 . 2 Keyboard and Mouse Problems... -
Page 23: General Maintenance
6 . 1 6 . 2 General Maintenance Safe Use of the System...
Need help?
Do you have a question about the K8NBD-S9 and is the answer not in the manual?
Questions and answers