Advertisement
Quick Links
Battery Installation:
1. To open cover: With keypad facing you, first slide dark lens cover away from you (photo A, step 1)
and then lift lid upward from the back (photo A, step 2)
2. When placing
two AAA batteries
should make contact with the corresponding + and - end of each battery (photo B).
3. Closing cover: With keypad facing away from you gently close cover by pressing downward
(photo C, step 1) and sliding it toward the front (keypad) until it is aligned. (photo C, step 2)
4. Test remote by pressing the power button; the LED should light, indicating that the batteries are in
correctly. If the LED doesn't light, then the batteries are either in wrong or the batteries are bad.
Photo A
Open with keypad facing you
No Setup required for ANY Samsung or LG TV. Also works RCA (commercial TVs) with no setup.
FOR ALL OTHER TV BRANDS SEE EASY TV SETUP INSTRUCTIONS BELOW
1.
Turn ON the TV and then stand back about 5 feet from TV and point the remote at the CENTER
of the front panel of the TV
remote is set-up.
2.
Press and firmly Hold down the SETUP button, do not release. The LED will blink once and then
after 7 seconds it will start code search. The LED will continue to blink every 2 seconds. Once your
TV shuts OFF immediately remove your finger from the SETUP button; the code automatically
locks in.
3.
Testing the remote:
For TV Only: Test Power, Volume and Channel Functions, if all work correctly setup is
complete. If not, you may not have an exact code match. Start again at step #1. The code
search will continue where it left off.
For TV Plus Cable Box: Only test Power and Volume function, DO NOT CHANGE
CHANNELS. If these functions operate correctly please turn page over and see Page 2.
Important Note: If you think you missed the TV code or you intend to use the remote on a different
R
eset the remote back to the beginning of the code search: Press and hold the SETUP button
brand TV:
down, then press and hold the CC button down at the same time until the red LED light blinks quickly 3
times, then release both buttons. You have now reset the code list back to the beginning. Now repeat step
1-3 from the Easy TV Setup above.
Copyright© 2020, Starlight Electronics LLC, Command In Hand Inc.
INSTRUCTIONS FOR CR3BCB-H
in the compartment note the + and - symbols on the metal hinge
Photo B
Close with keypad facing away from you
.
It will not be necessary to point the remote at that exact area once the
Photo C
PAGE 1
Optional screw for
the battery
compartment is in
bag with remote
Important
Multi-Bed Setup See Page 3
rev. 03-25-20
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Clean Remote CR3BCB-H
Summary of Contents for Clean Remote CR3BCB-H
- Page 1 INSTRUCTIONS FOR CR3BCB-H Battery Installation: 1. To open cover: With keypad facing you, first slide dark lens cover away from you (photo A, step 1) and then lift lid upward from the back (photo A, step 2) 2. When placing...
- Page 2 Hint: If your Cable Provider is not listed, please search by the manufacturer of your cable box. Note: If your cable box has a power button, use the CBL button on Clean Remote to power it on or off. TV and Cable Box Trouble Shooting...
- Page 3 MULTI-BED TV INSTRUCTIONS FOR HEALTHCARE TVs WITH THIS FUNCTION ONLY Before proceeding, please ensure that your TV has the Multi (bed)-Code feature and the TV has been set to the appropriate Multi-bed setting. You will need to refer to your TV’s manual for the TV’s Multi-bed setup instructions.
- Page 4 PLEASE TURN INSTRUCTIONS OVER AND BEGIN AT PAGE 1 PAGE 4 Copyright© 2020, Starlight Electronics LLC, Command In Hand Inc. rev. 03-25-20...
Need help?
Do you have a question about the CR3BCB-H and is the answer not in the manual?
Questions and answers