Table of Contents
Advertisement
Quick Links
Operation Manual
BWM LSV30H Vertical Log Splitter
Instruction & Assembly
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
SAVE THIS INSTRUCTION FOR FUTURE REFERENCE
Warning:
Failure to follow this important safety information may result in serious injury to the user or
bystanders, or cause equipment damage.
Version 202401 Updated 05/2024
Advertisement
Table of Contents
Related Manuals for BW Machinery LSV30H
Summary of Contents for BW Machinery LSV30H
- Page 1 Operation Manual BWM LSV30H Vertical Log Splitter Instruction & Assembly IMPORTANT READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION SAVE THIS INSTRUCTION FOR FUTURE REFERENCE Warning: Failure to follow this important safety information may result in serious injury to the user or bystanders, or cause equipment damage.
-
Page 2: Table Of Contents
Table of Contents Important Safety Information ...................1 Operation Warnings ............................. 1 Crush and Cut Hazards ..........................1 Hazard Signal Word Definitions ........................1 Assembly Overview ....................2 Step 1: Wheel Assembly ........................... 2 Step 2: Attach Tow Bar to Oil Tank ......................... 2 Step 3: Attach the Engine and Cylinder Mounting Bracket ................ -
Page 3: Important Safety Information
Important Safety Information Read and understand the complete Operation Manual before assembling or using this product! Failure to comprehend and comply with warnings, cautions and/or instructions for assembly and operation could result in serious injuries or death. Save these instructions for further reference. The actual product is slightly different from the manual, please refer to the actual product as the standard. -
Page 4: Assembly Overview
Assembly Overview Set the shipping crate on a solid flat surface and carefully remove the lid. Use two people and take all parts out of the shipping crate and inspect the components to ensure there are no missing pieces before starting to assemble the log splitter. -
Page 5: Step 3: Attach The Engine And Cylinder Mounting Bracket
2. Fix the tow bar to the fuel tank (# 1) using four sets of hex bolts M8 × 90 (# 29), flat washers 8 (# 28), and hex lock nuts M8 (# 27). Step 3: Attach the Engine and Cylinder Mounting Bracket 1. -
Page 6: Step 4: Attach The Lifting Table
3. Connect the gear pump to the engine (# 82) and tighten it with 4 5/16-2 bolts (# 69), 4 spring washers (# 79), and 4 flat washers (# 28). Step 4: Attach the Lifting table Secure the lifting table (# 54) to the mounting bracket (# 78) using the shaft (# 64), flat washer M12 (# 25), and hex lock nut M12 (# 23). -
Page 7: Step 6: Attach The Oil Pipe Correctly Complete
Step 6: Attach the oil pipe correctly complete. Version 202401 Updated 05/2024... -
Page 8: Step 7: Add Engine Oil
Step 7: Add Engine Oil 1. Make sure the log splitter is on a level surface. 2. Remove oil fill cap / dipstick to add oil. 3. Refer to the separate owner's engine manual for the amount needed for engine oil; replace oil fill cap/dipstick 4. -
Page 9: Step 9: Add Hydraulic Oil
CAUTION 1. Fuel and fuel vapors are highly flammable and extremely explosive. 2. Fire or explosion can cause severe burns or death. 3. Unintentional startup can result in entanglement traumatic amputation or laceration. 4. Only use regular unleaded 91 fuel. 5. -
Page 10: Operation Instructions
Operation Instructions WARNING Before operating or using the log splitter, review the instructions below and all safety information. Failure to follow these instructions may result in property damage or injury to the operator or bystanders. WARNING Always use the log splitter for its intended use. Only use the log splitter to split wood logs, lengthwise with the grain. - Page 11 6. The log splitter must have at least two metres of clearance from combustible materials. It needs to be on a dry and level surface with good footing. Do not work on mud, ice, brush or snow. When using the log splitter the work zone must be maintained at all times. NOTE: Serious accidents can happen when other people are allowed inside the work zone.
- Page 12 11. Load a log onto the beam against the end plate (Max. log length is 60cm). 12. Make sure hands are clear from the wedge and crush hazard areas. 13. Push control lever FORWARD by one hand to split the log. 14.
- Page 13 Horizontal Using Only For Vertical Towing Turn up the lifting table and tighten with hinge pin Hook safety chain to towing vehicle Version 202401 Updated 05/2024...
-
Page 14: Maintenance And Storage
Maintenance and Storage WARNING Improper maintenance and storage of the log splitter may void your warranty. MAINTENANCE ♦ Before performing maintenance, the log splitter must be placed in maintenance mode. Turn off the engine and move the control lever forward and backwards to relieve the hydraulic pressure. ♦... -
Page 15: Troubleshooting
Troubleshooting Problem Cylinder rod will not move Solution: A, D, E, H, J Slow cylinder rod speed when extending or Solution: A, B, C, H, I, K, L retracting Wood will not split or splits extremely slowly Solution: A, B, C, F, I, K Engine bogs down during splitting Solution: G L Engine stalls under low load condition... -
Page 16: Specifications
Specifications Ram Force ........................ 30T Cycle Time ....................... 15S Hydraulic Tank Capacity ..................14L Max. Log Length ..................58cm (22.8") Hydraulic Cylinder ..................4½" ×22¾" Max. Pressure....................3000 PSI Gear Pump ................... 12GPM 2- Stage Wheel Size ......................17.7" Hitch Type ..................50mm Ball Coupler Max. -
Page 17: Illustrated Parts List
Illustrated Parts List Version 202401 Updated 05/2024... - Page 18 Part No. Description BWMLSV30H-001 Oil Tank BWMLSV30H-002 Right and Left Protection Fender Flat Washer Ф10 BWMLSV30H-003 BWMLSV30H-004 Hex Lock Nut M10 BWMLSV30H-005 Hex Bolt M10×25 Spring Washer Ф10 BWMLSV30H-006 BWMLSV30H-007 Tyre/Wheel BWMLSV30H-008 Axle Cap BWMLSV30H-009 Cotter Pin d4*40 BWMLSV30H-010 Slotted Nut M20×1.5 Flat Washer Ф20 BWMLSV30H-011 BWMLSV30H-012...
- Page 19 BWMLSV30H-050 Axe fixing plate BWMLSV30H-051 Cylinder BWMLSV30H-052 Wedge Pin BWMLSV30H-053 U-shaped bolt BWMLSV30H-054 Lifting Table BWMLSV30H-055 Pipe sleeve BWMLSV30H-056 Suspension ear BWMLSV30H-057 Hex Bolt M8×16 BWMLSV30H-058 Pipe sleeve BWMLSV30H-059 optical axis BWMLSV30H-060 Bearing Steel Wire Snap Ring for Shaft Ф40 BWMLSV30H-061 BWMLSV30H-062 Pallet...
- Page 20 BWMLSV30H-100 Hex Bolt M12×55 BWMLSV30H-101 Plate BWMLSV30H-102 Hex Bolt M8×70 BWMLSV30H-103 Cotter Pin d5*50 BWMLSV30H-104 Hex Nut M8 BWMLSV30H-105 Tie rod BWMLSV30H-106 Torsion spring BWMLSV30H-107 O Ring D80*2.4 Spring Washer Ф12 BWMLSV30H-108 BWMLSV30H-109 Gear pump joint BWMLSV30H-110 Return oil pipe BWMLSV30H-111 Oil inlet joint BWMLSV30H-112...
Need help?
Do you have a question about the LSV30H and is the answer not in the manual?
Questions and answers