1. Manuals
  2. Brands
  3. BW Machinery Manuals
  4. Log Splitter
  5. LS30 Series
  6. User manual

BW Machinery LS30 Series User Manual

30 ton log splitter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
BWM 30 Ton Log Splitter
User's Manual
BWM LS30 Series
Please read through this owner's manual carefully before using the product, to ensure the
safety of yourself and others.
*Due to continuing improvements, actual product may differ slightly from the product described
herein.
Version 202201 Updated 09/2022

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LS30 Series and is the answer not in the manual?

Questions and answers

Related Manuals for BW Machinery LS30 Series

Summary of Contents for BW Machinery LS30 Series

  • Page 1 BWM 30 Ton Log Splitter User’s Manual BWM LS30 Series Please read through this owner’s manual carefully before using the product, to ensure the safety of yourself and others. *Due to continuing improvements, actual product may differ slightly from the product described herein.

  • Page 2: Table Of Contents

    Index 1. General Warnings and Rules ..............3 2. Hazard Signal Definitions ................ 4 3. Controls and Features Identification ............5 4. Assembly Instructions ................7 5. Operating Instructions ................13 6. Maintenance and Storage ..............17 7. Troubleshooting ..................18 8.

  • Page 3: General Warnings And Rules

    GENERAL WARNINGS READ and UNDERSTAND this manual completely before using 30 Ton Log Splitter. Operator must read and understand all safety and warning information, operating instructions, maintenance and storage instructions before operating this equipment. Failure to properly operate and maintain the log splitter could result in serious injury to the operator or bystanders. Operation Warnings ...

  • Page 4: Hazard Signal Definitions

    Hazard Signal Word Definitions This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER indicates an imminently hazardous DANGER situation which, if not avoided, will result in death or serious injury.

  • Page 5: Controls And Features Identification

    Controls and Features Identification Read this owner’s manual before operating the equipment. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. 1. 2” Coupler – Attaches the log splitter to the 2” ball 2.
  • Page 6 WARNING Read and follow all instructions for assembly and operation. Failure to properly assemble this equipment could result in serious injury to the user or bystanders, or cause equipment damage . Engine Shipped Without Oil. Before starting engine, fill with SAE 10W-30 motor oil or Honda 10W30 engine oil, depending on your model.

  • Page 7: Assembly Instructions

    Assembly Instructions 30 TON LOG SPLITTER ASSEMBLY Set the shipping crate on a solid flat surface and carefully remove the lid. Use two people and take all parts out of the shipping crate and inspect the components to ensure there are no missing pieces before starting to assemble the log splitter follow steps 1 through 8.
  • Page 8 STEP 2: Attach Tow Bar to the Oil Tank 1. Attach the tow bar (#59) to the oil tank and secure using two sets of hex bolts M12x100 (#24), flat washers Ø12 (#62) and nylon lock nuts M12 (#13). STEP 3: Attach the Beam Assembly 1.
  • Page 9 STEP 4: Attach the Engine （Assembled in Australia Factory） 1. Place four sets of polyurethane blocks (#71) and large flat washers Ø10 (#72) on the mounting plate. 2. Position the engine (#33) over the blocks and washers, secure it to the mounting plate, put the hex bolts M8x65 (#46) through the bottom of the plate (bolts should go through blocks, flat washers and engine base).
  • Page 10 STEP 5: Attach Hydraulic Hoses, Manual Canister, Log Cradle and Fenders 1. Put O ring Ø11x2.5 (#19) on the gear pump outlet connector (#23), attach the hydraulic hose (#16) to the gear pump outlet connector (#23). 2. Put O ring Ø17x2.5 (#68) on the spin-on filter connector (#50), attach the hydraulic hose (#7) to the connector (#50).
  • Page 11 STEP 6: Add Engine Oil 1. Make sure the log splitter is on a level surface. 2. Unscrew the oil fill cap/dipstick to add oil. 3. Refer to owner’s engine manual for the amount needed for engine oil (SAE30 or 10W30, depending on your model);...
  • Page 12 6. With the wedge retracted, check hydraulic oil level again and fill if necessary. WARNING DO NOT remove the hydraulic oil fill cap when the engine is running or hot. Hot oil can escape causing severe burns. Always allow the log splitter to cool completely before removing the hydraulic oil cap.

  • Page 13: Operating Instructions

    Operating Instructions WARNING Before operating or using the log splitter, review the instructions below and all safety information. Failure to follow these instructions may result in property damage or injury to the operator or bystanders WARNING ALWAYS use the log splitter for its intended use. ONLY use the log splitter to split wood logs, length wise with the grain.
  • Page 14 NOTE: Serious accidents can happen when other people are allowed inside the work zone. Keep everyone else outside the work zone while operating the control lever. 7. Always wear safety gear, eye protection, gloves and work boots when operating the log splitter.
  • Page 15 12. Make sure hands are clear from the wedge and crush hazard areas. CRUSH WARNING Wedge can cut through skin and break bones. Keep both hands away from wedge and beam slide. Serious accidents can happen when other people are allowed inside the work zone. Keep everyone else out of the work zone while operating control lever.
  • Page 16 Operating Instructions - 16 - Version 202201 Updated 09/2022...

  • Page 17: Maintenance And Storage

    Maintenance and Storage CAUTION Improper maintenance and storage of the log splitter may void your warranty. MAINTENANCE • Before performing any maintenance, the log splitter must be placed in maintenance mode. Turn off the engine and move the control lever forward and backwards to relieve the hydraulic pressure.

  • Page 18: Troubleshooting

    Troubleshooting Problem Cylinder rod will not move SOLUTION: A,D,E,H,J Slow cylinder rod speed when extending or SOLUTION: A,B,C,H,I,K,L retracting Wood will not split or splits extremely slowly SOLUTION: A,B,C,F,I,K Engine bogs down during splitting SOLUTION: G,L Engine stalls under low load condition SOLUTION: D,E,L,M Engine starts problem SOLUTION: N...

  • Page 19: Specifications

    Specifications Ram Force ....................30 Ton Cycle Time ....................12 Sec Wedge Size ................8” Hardened Steel Max. Log Length ....................26” Gear Pump....................2-Stage Hydraulic Oil ................AW46 Hydraulic Oil Hydraulic Cylinder ................4.5” x 24.5” Max. Pressure ..................3500 PSI Max.

  • Page 20: Warranty

    Warranty Limited Warranty The warranty period for the log splitter is 2 years (Domestic use) and 1 year (commercial use) from the purchase date. The engine has a 3 year warranty. The warranty will not apply to any unit which was not assembled correctly, misused, overloaded or which has been used or operated contrary to our instructions, or which has been repaired or altered by anyone other than an authorized representative.

  • Page 21: Illustrated Parts List

    Parts Illustration List 69 31 32 56 32 36 36 32 31 36 32 31 45 47 67 68 50 13 62 24 87 88 89 - 21 - Version 202201 Updated 09/2022...
  • Page 22 Parts Illustration List Ref # Part No. Description BWMLS300001 Hex Bolt M5x10 BWMLS300002 Inner Hex Cone Point Set Screw M6x10 BWMLS300003 Cylinder BWMLS300004 Metal Hydraulic Hose BWMLS300005 R Pin Ø4.5 BWMLS300006 Cylinder Pin BWMLS300007 Hydraulic Hose (Valve - Spin-on Filter) BWMLS300008 Cutting Sleeve Connector BWMLS300009...
  • Page 23 Ref # Part No. Description BWMLS300037 Thin Hex Slotted Nut M20 BWMLS300038 Angle Connector BWMLS300039 Oil Filter BWMLS300040 Cotter Pin Ø3x30 BWMLS300041 Axle Cap BWMLS300042 Rubber Washer BWMLS300043 Wire Snap rings for shaft BWMLS300044 Oil Tank BWMLS300045 Flat Washer Ø6 BWMLS300046 Hex Bolt M8x65 BWMLS300047...
  • Page 24 Ref # Part No. Description BWMLS300076 Large Flat Washer Ø6 BWMLS300077 Nylon Lock Nut M6 BWMLS300078 Nylon Lock Nut M14 BWMLS300079 Spin-on Filter BWMLS300080 Oil Seal BWMLS300081 Conical Roller Bearing BWMLS300082 Hex Bolt M12x35 BWMLS300083 Hex Bolt M8x25 BWMLS300084 Rubber Washer BWMLS300085 Left Fender BWMLS300086...

Table of Contents