Related Manuals for klover GE2606
Summary of Contents for klover GE2606
- Page 1 Assembly Instruction MODEL: GE2606 PRODUCT SIZE(LxWxH):436x295x270cm PLEASE READ CAREFULLY BEFORE ASSEMBLY...
- Page 2 CONTENTS 1. Assembly Advice ..............Page 1 2. Product Features ..............Page 2 - 3 3. Parts List ................Page 4 - 6 4. Roof Vent Assembly ............Page 7 - 8 5. Door Assembly ..............Page 9 - 11 6. Base Assembly ..............Page 12 - 13 7.
- Page 3 Assembly and Maintenance Advice 1. For safety purposes, we strongly recommend that this product is assembled by at least two people. 2. Some components have sharp metal edges. Please be careful when handling metal components. Please wear gloves, shoes and safety goggles during assembly. 3.
-
Page 4: Functions And Features
Functions and Features: 1. Compared with traditional greenhouses this new product features many significant improvements. The hollow box profile aluminium framing is much stronger than other greenhouses and it can withstand much greater pressure. 2. Base anchor brackets are included as standard with expanding bolts to ensure a secure fixing into concrete or paving. - Page 5 5. Manual window handles are included as standard with the roof vents. If required, automatic roof vent openers are available as an inexpensive optional extra. Automatic opener Manual opener GM80002 is sold separately 6. Remove approximately 2 inches of film from all sheet edges before installing and remove all film immediately after the construction is completed.
- Page 6 GE2606(ALU.BoxNo.1) PART NO L07B L07B L08B L08B L09B L09B PART L01A L03F L04A L04B L05B L23A...
- Page 7 GE2606(ALU.BoxNo.2) PART DOOR L03A PART L03A L03A L16A L03A L16B L03A L18A L03D L18B L03E L18C L18D L05G PART PART PART L02F L02E Ø4X16D M4.2X16 L03B M4.8X16 L03C M6X12 L05A L05C L05E M5X12 L05E M5X12 L05E Ø3.2X10 L05F D115 L15A...
- Page 8 GE2606(PC/Glass BOX NO.1) PART Rubber for walls only (Provided for glass only) PART PC/Glass 222M J107 N0.1...
- Page 9 GE2606 (PC+Glass) PART Rubber for walls only (Provided for glass only) PART 148M J107 Glass N0.1 PART Glass N0.2...
- Page 10 PART Window L19A L19B M4.2X16 L19A L19A L19B Fix A01 in the middle of L19B, 322.2mm from the ends. Insert H43 into the Slot Slot of L19A,L19B & L20 Insert Part B into the tube L19B Tube of L19A,L19B & L20 After connector D46 &...
- Page 11 PART PART 2.65M J107 L15A L15A M4.2X16 Ø4X16D J107 If glass is chosen, please seal it with rubber (J107) provided. If polycarbonate sheet is chosen, rubber is not provided. Please seal it with silicone sealant (not provided).
- Page 12 PART Left Door L18A L16A L16B L18A L05G L18B L16B L18C L18D L18D L05G M5X12 L05G M4.2X16 M6X12 L18B Insert Connector D45 into each end of frame profiles L16B & L18A & L18B & L18D, and then fix them with screws Z08. Before fixing with screws, please mark them with a pencil at distance about 20/30mm from each end, and make sure there is no gaps...
-
Page 13: Right Door
Right Door L18B L05G L18C L16A L05G L18A Insert Connector D45into each end of frame profiles L16A & L18A & L18B & L18C, and then fix them with screws Z08. Before fixing with screws, please mark them with a pencil at distance about 20/30mm from each end, and make sure there is no gaps between each profile. - Page 14 PART 12.2M J107 J107 J107 If glass is chosen, please seal it with rubber(J107) provided. Noted: Rubber is not provided if you choose polycarbonate sheet as glazing panel.
- Page 15 Expansion screw/Concrete ground It is essential the dimensions a & b are the same to ensure the base is square. Steel pegs in soil Support at the corners only is inadequate.
- Page 16 PART M8X60 Expansion bolts assembly * This shows a layout for D22's positions where it is placedin the middle of the glazing panel for each section.
- Page 17 PART L08B L01A L08B L08B M5X12 L08B L08B Insert J41 into each L08B L08B L01A L01A L01A L01A L01A Fix L01A to L08B through J41, using S26.
- Page 18 PART L07B M5X12 L07B L07B L07B L07B Insert J39 into L01A, and then fix L07B to L01A using S26. Make sure the angle is Right Angle before tighting them up. L07B L07B...
- Page 19 PART L01A L03A L01A M5X12 L01A L01A Insert Panel Y5 into the channel of L01A, and then fix a L03A to L08B & 07 B using S26. Make sure the other side of Y5 is completely the channel of L03A. Insert anoth Y5 into the channel of L03A, then fix another L03A using S26.
- Page 20 PART L04A L04B L03A M5X12 Y6 is the last panel to slide in, for assembling window later. L03A L04B L04A L03A Fix L04A/L04B Y5 same as the back wall assembly using S26. L07B L03A L03A L08B...
- Page 21 PART L05B L05B L05B L05C M5X12 M4.2X16 L05B L05C Install L05B (3PCS) L05C Fix two ends of L05B onto L01A using S26, fix L05B to L03A with the self-tapping screws (Z08) using a powered screwdriver. Install L05C (2PCS) Fix two ends of L05C onto L01A & L04A/L04B using S26, fix L05C to L03A with the self-tapping screws (Z08) using a powered screwdriver.
- Page 22 PART L02E M5X12 M4.2X16 L03A L02F L03A L02E L02E Insert the other end of Y6 into the channel of L02E. Fix plate D49 onto L02E and L03A, using S26 and Z08 as shown above.
- Page 23 PART WINDOW M5X12 M4.2X16 1. Fix D49 onto the window profile L11 using S26; 2. Make a mark on L03A at distance 593MM from L02E (as shown on the left). Do the same on the other end. 3. Fix the window to L03A, using Z08. 4.
- Page 24 PART D115 M4.2X16 Auto-opener Assembly (optional) L02E D115 L19B L02E D115 Fix D115 onto L02E, using Z08; and fix the auto opener onto D115 and L19B (window profile), using Z08.
- Page 25 PART J107 If glass is chosen, please seal it with rubber(J107) provided. J107 J107 J107...
-
Page 26: Roof Assembly
PART Roof Assembly L23A L23A L23A M5X12 L23A L23A L23A Fix 4 X L23A to D54 as shown above, using S26. L23A L23A Fix the roof profiles L23A to L07B with D52, using S26. Note: Extra hands are needed to hold the profiles when you do this assembly. - Page 27 PART L03D L03E L05A L03F L05A L05A L03D L03F L03E M5X12 M4.2X16 L03F L03F Fix L03F (4 PCS) to D54 & L07B as shown, using S26. Twist M06 into the bolt on D55, and then insert the bolt of D55 through D54. Adjust the position of the above M06 to allow L03D&L03E enough space for another M06 below to...
- Page 28 PART 77.3M L02F J107 L03B L03C L09B L03B L03C L03B&L03C M5X12 M4.2X16 L03B&L03C Fix L03B & L03C to L07B & L23A as shown Insert Y1/Y2 into the right position before fixing L03B /L03C. J107 J107 If glass is chosen, please seal it with rubber(J107) provided.
- Page 29 Y12 Y13 Insert Y3, Y4, Y12 & Y13 into positions. L02E Aligned overlap Y12&Y13 L02F L05A Insert the other end of Y12/Y13 into the channel of L02F, and then fix it to L05A, using Z08. Make sure L02F and L05A must be aligned.
- Page 30 If glass is chosen, please seal it with rubber(J107) provided. J107 J107 Insert Y14 into positions.
- Page 31 Gutter Assembly When the panel s are completely inserted, fix gutter L09B to profile L07B. Tap it gently into position with a rubber mallet. L07B L09B Do the same on the other sides...
- Page 32 PART L05E L05F M4.2X16 L05F L05E L05E L05E L05E L05E 5F to two L03F using Z08. 5E(1 pc) to two L03F using Z08. e other L05E(17 pcs) to L03B/L03C/L03D/L03E/L03F & L03A using Z08 ow above.
- Page 33 PART M4.2X16 M4.8X16 M5X12 Right Door Left Door Fix L24 to L07B, using Z08. Left Door Right Door Fix L25(4 PCS) one side on the door profile and the other side to L04A/L04B using S27. Then secure with Z17.
- Page 34 PART Ø3.2X10 M4.2X16 Z06&Z08 Drill the holes on each L03A as shown, Dia.3.2mm, and secure the hooks H74 with Z06 & Z08,then ensure H74 works with Door properly when the doors are open. Drill a hole in L01A, approximately 3mm diameter and 700mm If you wish to eliminate leaks up from the bottom.
Need help?
Do you have a question about the GE2606 and is the answer not in the manual?
Questions and answers