1 Supply cable 5 Control panel 2 High pressure intake hoses 6 Drum door 3 Flexible drain hose, with detachable 7 Access panel for lint filter and drain swivel elbow pump 4 Detergent dispenser drawer 8 Four height adjustable legs...
Pushbuttons for additional functions. Time display “hours, mins”. SPIN SPEED SELECTOR switch. “Door” button; PROGRAM SEQUENCE indicators opens the drum door. (LED indicator lamps). “ON/OFF” button; PROGRAM SELECTOR switch. Turns the machine on and off or interrupts a program. The “On” lamp illuminates.
Rather than throwing these materials before you use your new machine for away, please take them to your commu- the first time, or if it has been in storage nity recycling center. for more than a few weeks between uses.
Optimal usage Optimal usage Economy The key to good wash results is finding the correct combination of detergent To conserve energy, remember the fol- and temperature, and then allowing the lowing tips: washing machine to optimize their us- – The automatic load control feature age through its programming.
^ Sort the laundry Only wash items that are labeled ma- chine washable by the manufacturer. Some garments will have a Fabric care label in the collar or side seam. If so, sort the laundry by care label and color.
The program selector can be turned to COTTONS... . 11 lbs (5.0 kg) the left or the right. PERMANENT PRESS. . . 4.5 lbs (2.0 kg) FINE/DELICATES ..2.0 lbs (1.0 kg) WOOLENS.
You may seriously injure yourself. If the drum turns with the door open, contact the Miele Service Department. Check the folds in the door seal for any small articles such as buttons or nails which may be lodged there.
“Finish/Start” To continue the program, turn the ma- As soon as the program sequence indi- chine back on. cator lamp for the stage you wish to en- ter starts flashing: To change an incorrectly selected program: ^ Turn the program selector switch to ^ Turn the program selector switch to the desired program.
Adding fabric softener or starch Adding fabric softener or starch If fabric softener is desired, it will work At the end of the program a small more effectively and be gentler on the amount of water will normally remain in...
140 - 190°F Exclusively white items. PERMANENT PRESS 85° For dark fabrics which are a blend or 100% For cotton blends, polyester synthetic fabrics. blends and synthetics such 105 - 120°F For light colored cotton or synthetic items.
Program selection max. load Additional options Normal wash cycle Rapid wash available cycle 11 lbs Pre-wash Available Available Water plus Gentle wash 4.5 lbs Pre-wash Available Available Water plus Gentle wash 2 lbs Pre-wash Available Available Gentle wash 2 lbs Available –...
The suds are cooled at the end of the wash cycle by incoming water, and drained in intervals. This minimizes the danger of creasing by avoiding sudden temperature changes. (1) Increased water level: The water level can be increased from the normal level to a higher level by pressing the „ Water plus” button.
„Without final spin”: At the end of the final rinse the wash remains suspended in water if the SPIN SPEED SETTING is set to „ Without final spin”. This helps to reduce creasing if the laundry will not be removed immediately upon...
Textile care symbols Textile care symbols Some clothing manufacture’s place tex- Hand wash tile care symbols on their products. The do not wash following is an explanation of some of these symbols. dry clean only do not dry clean Washing (°C)
By using the pushbuttons to select one The “Water plus” option is available in or more additional options, basic pro- the following programs: grams can be tailored to the type of – The wash and rinse cycle in COT- laundry being washed. TONS.
Cleaning and care Cleaning and care To clean the washing machine: ^ Clean the casing using a mild non- abrasive detergent or soap and water, and wipe dry with a soft cloth. ^ Clean the control panel with a damp cloth.
^ Turn the lint trap lid counterclockwise 2 - 3 times. Do not remove it. Approx. 2 quarts (2 l) of water will drain out of the hose. If the main drain hose is clogged, more water will be retained in the machine (max.
Cleaning and care ^ Once the flow of water stops, remove the lint trap and clean it. ^ Clean the inside of the lint trap hous- ing. ^ Remove any foreign objects (e.g. Remove any detergent deposits or for- buttons, coins, etc.) or lint.
Inspect the inlet hose regularly. The hose should be replaced if there are The washing machine has two water in- small cracks in the surface, or if it has let filters to protect each inlet valve. been otherwise damaged or cut.
Problem solving guide Any work done on the electrical components of this appliance should only be performed by a qualified technician in accordance with all local and na- tional codes and regulations. Unauthorized repairs may result in personal injury and machine damage.
The spin speed selected Select a higher spin . . . The wash is too wet was too low. speed next time. after the final spin? The load was not evenly...
Problem solving guide What to do if, . . . Cause . . . Remedy . . . A water inlet filter is Clean the water inlet fil- . . . In spite of adequate blocked. ters. water supply, the water...
Problem solving guide What to do if, . . . Cause . . . Remedy . . . Insufficient detergent was – Add more detergent..Grey greasy parti- used to break down the – Before washing the...
^ Turn on the valve. the floor, make certain the machine is drained before opening the door. If 1 gallon (3.8 l) of water flows into the bucket in 15 seconds the water pres- ^ Turn off the washing machine.
After sales service After sales service If problems occur that cannot be easily fixed, or if the appliance is under war- ranty, please contact: – The nearest Miele Technical Service Department (see back cover). When contacting the Technical Service Department, please have the model...
Please note: during the spin cycle than wooden ^ Do not lift the machine by the drum floors. door. Please note the following points: ^ Ensure that the machine feet and the...
INSTALLATION INSTRUCTIONS ^ Turn the right shipping strut 90° ^ Plug the two holes with the plastic clockwise. caps provided. Movement of the machine without the shipping struts in place should be kept to a minimum. The shipping struts should be stored in a safe place for future use.
Leveling the machine much as necessary by turning both To ensure smooth operation, it is es- the foot 1 as well as the locking ring 2 sential that the machine is level. to the left using a screwdriver (see il- lustration).
This Miele washing machine can be in- washer, at least a gap must be stalled as part of a washer dryer stack left between the top of the machine in combination with a Miele tumble and bottom of the countertop; and dryer.
You can set the water hard- ^ Do not put any laundry in the ma- ness dial in the detergent dispenser as chine. a reminder.
Drain connection Connect the cold water intake hose (blue mark) to the cold water valve and The 5 ft. (1.5 m) drain hose may be the hot water intake hose (red mark) to connected as follows: the hot water valve.
The washing machine is supplied with a electric shock by providing a path of 5 ft long, 4 wire cord, ending in a NEMA least resistance for the electric current. 14-30 P plug, ready for connection to a...
Extra water intake through cession. A new program can be se- compartment i lected as soon as the “On” lamp is the only one remaining lit. A 10 second water intake through com- partment during the main wash can be added.
Programmable functions Step 1: Turn off the machine, close the door, and release all pushbuttons. Set the Progam Selector Switch to “Finish/Start”. Step 2: 4 seconds. ^ Press the “ON/OFF” button Step 3: ^ Press the “Water plus” button 4 times (i.e.
Programmable functions Step 4: ^ Set the Program Se- lector to “Fine rinse”. Desired function: Continue with Step 5 High water level to activate. ^ Set the Program Se- lector to “Drain”. Con- 5th rinse cycle tinue with Step 5 to activate.
Programmable functions ^ Set the Program Selec- tor to “WOOLENS 85°”. Additional rinse in Continue with Step 5 Rapid wash to activate. Step 5: ^ Press the “Water plus” button twice (i.e. in and out once) to tog- gle the function “ON/OFF”.
^ Perform Steps 1 to 4. Follow the same instructions given un- der “To activate the additional func- If the “Rinse 1-2" lamp lights, the pro- tions”, steps 1 to 5. grammable function is active. When the “Rinse 1-2" lamp goes out;...
Technical data Technical data 1.1 Dimensions Height “ - 34" Height without lid " - 33" Width “ Depth (including distance from wall) 24" Weight 220 lbs. Capacity 11 lbs. dry laundry Rated load 2.8 kW Circuit breaker 15 Amp Water pressure 14.5-145 p.s.i...
Drainage is via a 5 ft. long, 1 “ OD hose. This washing machine is supplied with a 5 foot long cable with plug for con- nection to a 120/240 V (208 V) 60 Hz (3-pole-4 wire grounding) power sup- ply.
Alteration rights reserved/004 3200 These instructions are printed on 100% unbleached, recycled paper are completely Biodegradable.