Related Manuals for FESTA S1M-HJ2118-230
Summary of Contents for FESTA S1M-HJ2118-230
- Page 1 Angle grinder 230mm Item No.: 28215 Model No.: S1M-HJ2118-230 Manual for use Please read this manual carefully before using.
-
Page 2: Technical Specifications
1. Technical specifications Item No. 28215 Model No. S1M-HJ2118-230 Rated voltage 230 V, 50 Hz Power 2400 W No load speed 6600 min −1 Protection class Disc diameter Max 230 mm Bore diameter ø 22.2 mm Length of electric cord... -
Page 3: Work Area Safety
3. Safety Warning: Using any tool can be dangerous. Always select the right tool for the job. Caution: The tool can get hot after use. Should be used by a competent person. If in doubt consult an electrician. Cutting/Grinding: Before attempting to cut/grind any object, first familiarize yourself with the correct procedures and techniques of cutting/grinding as well as the different cutting discs,... -
Page 4: Personal Safety
3.3 Personal Safety • Always wear protective equipment when operating a power tool. Proper protective equipment such as a dust mask, ear protection, and gloves will reduce personal injuries. • Proper workwear. Do not wear loose clothing or jewellery. Keep your hair, and clothing away from all moving parts. - Page 5 5. Tool & accessory use and care • Avoid forcing the power tool into the material. Allow the power tool to do the job for which it was designed for. Disconnect the plug from the power source before making any adjustments, changing •...
-
Page 6: Getting Started
6. Getting Started 6.1 Fitting the accessories 6.1.1 Auxiliary handle Figure 1 • Figure 1 1. Screw the auxiliary handle on to the slot. 2. Make sure the auxiliary handle is tightly screwed in, avoid over screwing, this will damage the thread. - Page 7 2. Be sure to tighten the screw securely, use the provided hex wrench to fasten the hex screw. 6.1.3 Cutting/ grinding blade. Figure 3 Figure 4 • Figure 3 1. Insert the blade and make sure its laying on top of the bottom flange nut securely, it must not move.
- Page 8 • Figure 4 1. Press the spindle lock button. 2. Twist the blade while pressing the spindle lock till it's locked in place and cannot turn. 3. Screw top flange nut flush with the blade. 6.1.4 Wrench Figure 5 • Figure 5 1.
-
Page 9: Operation
6.1.5 Inserting Wire Brush Figure 6 • Figure 6 1. Remove the top and bottom flange nuts, as they are not required for this accessory. 2. Insert the wire brush into the M14 threaded spindle. 3. Press the spindle lock button as you turn the wire brush. 4. -
Page 10: Maintenance
6.2.2 Abrasive cutting discs/diamond blades • Abrasive cutting discs/diamond blades cuts at 90° angle to the workpiece. • Note that diamond blades usually require less feeding pressure than abrasive discs. 6.2.3 Wire cup and wheel brushes • Don’t apply excessive pressure when using wire brushes, as this may prevent the tips from hitting the surface but rather cause the side of the wire to whip the surface. -
Page 11: Troubleshooting
power source before making any adjustments or maintenance procedures. 8. Troubleshooting Trouble Problem Suggested Action 1. Angle grinder 1.1 Power cord not plugged in 1.1 Ensure that the cord is connected to will not start 1.2 Power fault, fuse or circuit the power supply breaker tripped 1.2 Check the power supply... -
Page 12: Disposal Of Waste
9. Meaning of symbols on labels Meets relevant EU requirements. Electrical waste, see below Second class protection equipment. Double insulation Use certified eye and ear protection with a sufficient level of protection. Use certified respiratory protection with adequate level of protection Read the instructions before use. -
Page 13: Ec Declaration Of Conformity
Subjects of declaration-product identification: Product: Angle Grinder Model No.: S1M-HJ2118-230 Item No.: 28215 comply with the following harmonized standards, including their amending annexes, if any, by which conformity with the following harmonization provisions is declared:...
Need help?
Do you have a question about the S1M-HJ2118-230 and is the answer not in the manual?
Questions and answers